Hello, my partner! Let's explore the mining machine together!

[email protected]

coal mill reject system

coal mill - an overview | sciencedirect topics

coal mill - an overview | sciencedirect topics

To control the quality of coal being sent to the burners located on the furnace walls. The word quality here means the temperature and fineness of the PF. The set temperature values are dependent on the percentage of volatile matter that exists in the main fuel. The controlled temperature is important for many reasons such as stability of ignition, better grindability of solid fuels, better floating ability of suspended PF particles, etc. However, a temperature more than 65 to 70 is not recommended for various reasons.

Operating data from a coal mill is used to compare the fault detection observer-based method and PCA/PLS models based approach. There are 13 process measurements available representing different temperature, mass flows, pressures, speed etc in the coal mill.

The measurement is not updated, if the variation is less than 1%. The variations of T(t) is in the major part of the operational time inside this interval. Therefore, it is not suitable to be chosen as the predictor variable. However, the variations can be extracted from the TPA(t), which is used to control the temperature of the mill. Therefore, the PLS model is developed with the temperature of the mill as the dependent variable. In addition 6 of the other variables are chosen as regressors since there is barely information in the remainder.

A static PCA model is first developed, which captures around 99% of variations with 5 PCs (see Fig.5), which indicates strong collinearity among regressors. As shown in Fig.6, both Q and T2 statistics (with 95% confidence level) of the static PCA model are noisy, which potentially lead to false alarms. A static PLS model with 2 LVs achieves the minimal PRESS (see Fig.7), which is applied to the test dataset. Fig.8 shows the comparison between process measurement and the static PLS model prediction, together with the 95% confidence level. The process gradually drifts away form the NOC model, which eventually moves beyond the threshold around the sample 150. Due to the noise involved in the prediction signal, the estimation moves in and out the threshold from 110 till 200, when it is clearly out of the confidence level. Both Figs.6 and 8 reveal that static PCA and PLS models may lead to false alarms due to the noisy estimation. In addition, process measurements are commonly auto-correlated, this behavior is expected since the coal mill runs dynamical. Thus, dynamic models are developed by including time lagged process measurements, to address the issue of auto-correlations and reduce the possibility of false alarms due the none modeled dynamics.

Including time lagged terms enhance the NOC model by including historical data. However, time lagged terms also introduce additional noise into the modeling data block. For example, including n+1 time lagged terms might lead to poorer validation performance than the model with n terms due to measurement noise. Therefore, PRESS is used to choose an appropriate number of time lagged terms for a dynamic PLS model.

The predictive ability of the PLS model is improved with the inclusion of time lagged terms. The PRESS decreases from 1.645 to the minimal value of 1.142, which is obtained with a dynamic PLS of 3 LVs using 8 time lagged terms. The application of the dynamic PLS model to the test data reveals that the fault occurs in the process around sample 160. Fig.9 also shows a much smoother prediction such that the possibility of false alarms is significantly reduced. A dynamic PCA model is developed by the inclusion of 8 time lagged terms. The number of PCs is chosen as 2 through cross-validation, which explains 70.6% of process variations. The Q statistic of the dynamic PCA model is shown in Fig.10, the fault is detected around 160 samples, which is consistent with the dynamic PLS model.

The control loop for mill outlet temperature discussed here is mainly for TT boilers based on a CE design with bowl mill (refer to FigureVIII/5.1-2). A similar loop is valid for a ball-and-tube mill, which is discussed separately in the next section. In order to understand the loop in the figure, it is advisable to look at FigureVIII/5.0-1 and the associated PID figure (refer to FigureIII/9.2-4).

The outlet temperature of the coal mill is maintained at desired point so that the coal delivered from the mill is completely dry and achieves the desired temperature. Also, in case of high temperature at the mill outlet, cold air is blown in to reduce the risk of fire.

Normally, the entire requirement of PA flow necessary for a particular load at the mill is initially attempted through HAD so as to ensure complete drying of the coal (especially during rainy seasons) and to raise the mill temperature at a desired point. However, there may be times during hot dry summers when the mill outlet temperature shoots up. This is also never a desired situation because of fire hazard. In fact, to combat this fire hazard, arrangements for mill-inerting systems with inert gases (e.g.,N2 and CO2) need to be made (another purpose is to reduce air supply).

This is more important for ball-and-tube mills, especially when these are operated with one side only. Therefore, CAD comes into operation whenever there is need to bring down the mill temperature. Naturally when this damper operates (i.e., starts opening through process feedback), the hot air damper closes. Here also is a cross-operation of the two dampers but through process and not directly via the loop, so control loop disturbances are fewer than in the old days when cross-operations were implemented in the loop.

Mill outlet temperatures measured by redundant temperature elements and transmitters are put in an error generator. (Temperature element specialties were discussed earlier and so not repeated here.) The output of the error generator drives a PID controller. In general, since temperature is a sluggish parameter it is always advisable to use PID controllers for better results. To prevent controller saturation, controllers are put into service only when both the loops are in auto. The output of the controller through I/P converters normally drives pneumatic actuators meant for CAD.

As stated earlier, only when both HAD and CAD are in auto is the controller put into operation. Since FSSS operations depend on mill temperature conditions, with the help of the limit value monitor (LVM) necessary contacts statuses are shared with FSSS. The loop can be released to auto by an FSSS command. As a protection, both the full opening command and the >x% command for the mill CAD are issued from FSSS so sufficient cold air is circulated. If the auto release command from FSSS is missing or if HAD is in manual, it is necessary to inhibit auto operation so that the operator pay complete attention to the mill outlet temperature. That is the check back signal for FSSS from the loop for damper position.

How breakage energy and force are applied in the mill in order to achieve size reduction in an efficient and effective manner. This is a matter of design and performance of mills and the main subject of this section;

How the material being reduced in size behaves in terms of breakage characteristics such as strength and resulting broken size and shape. This relates to how the material responds to the application of breakage energy and force in terms of rate and orientation of application.

The analysis of individual mill design and operation is complex; so, for simplicity we will consider a typical mill layout for one mill type only. As VSMs have come to represent the bulk of the power station mill fleet, the explanation of mill operations will be based on this mill type. Figure13.2 illustrates the typical key components of a VSM.

In coal milling for power stations, a closed-loop process is used in which the rejects from the classifier are returned to the mill for regrinding. In VSMs, the re-circulation loop is within the mill, but some mill types would have an external loop. In fact, there are a number of re-circulation loops within a mill system. The situation is further complicated by the mill reject streams that reject undesirable material (tramp metal and non-coal bearing rock) from the mill. Generally, the following steps illustrate the path through a VSM:

Air entering through the Port Ring creates a fluidising zone in which heavy material (Mill Rejects) such as rock falls through the Port Ring into the Air Plenum below the Grinding Table and is ejected from the Mill through the Mill Reject System;

From the fluidising zone the ground coal is lifted up inside the Mill Body. Larger particles of coal reach a terminal velocity at which gravity will pull them back on to the Grinding Table for regrinding (Elutriation);

The fineness of the milling product and the capacity of the pulverizer are strictly connected. With increased fineness grows the overall circulation rate of coal in the mill, coal retention time and the flow resistance. As a result, the maximum mill capacity decreases and the rate of change of operational parameters of the furnace system deteriorates. In extreme cases, the performance of the boiler may be limited, and therefore improving the fineness of milling product must often include the modernization of the grinding system. The increase of the throughput of a pulverizer, which compensates the loss of capacity resulting from the increased fineness of coal dust, may be achieved through:

The analysis [45] proves that the maximum capacity of the ball-ring mill is obtained using 5 or 6 balls. Because earlier, as a rule, a greater number of balls was used, there is a possibility to increase the capacity by replacing the existing balls through a lower number of bigger balls. For example, in the EM-70 of FPM SA 9 balls of the diameter 530mm were replaced with 7 of 650mm. Such a modernized milling system can usually be set up on the existing gearbox. It should be noted that the costs associated with replacement of the classifier and the grinding elements are only slightly greater than the costs of the major repair of the mill. In the case where an existing mill has a grinding unit of the number of balls close to 6, the only way to increase performance is to increase the diameter of the balls, but this requires replacement of the mill body.

It has to be mentioned that the number of balls is increased during the mill operation. For example, the initial ten balls, after lowering the diameter below some value (due to wear), is complemented with the 11th additional ball.

If the existing pulverizer is equipped with 6 or 7 balls, increasing of its capacity is also possible by means of replacing the ball-ring system with the bowl and roller milling device. The milling costs per Mg of fuel in both systems are similar. However, with the same dimensions of the milling systems, the capacity of the roller system is about 15%20% higher. Another advantage is the shorter renovation time, which is about 714days for the ring-ball system, while for the roller mill, only 37days. In addition, hardfacing and re-profiling of grinding components are much easier for roller milling systems.

During the modernization of milling plant with compression mills, detailed analysis requires the selection of cross sections of nozzle-rings at the inlet of the drying agent to the mill, in order to minimize the amount of coal removed from the grinding chamber. The preferred solution is a rotating nozzle ring integrated with the bowl. This ring equalizes air distribution pattern at the periphery of the grinding chamber, which allows increasing the capacity of the grinding system without fear of excessive loss of fuel from the mill.

The rotational speed of the vertical spindle mill affects the operating conditions of the grinding unit. At high rotational speeds, the grinding unit operates at high flow of the material in the radial direction and low layers of the material under the grinding elements (balls, rollers). This causes the particles to be discharged without comminution and increases circulation in the mill. At the same time, the flow resistance and milling energy consumption (including erosive and abrasive wear) of the mill will increase.

If the rotational speed is too low, the material flow will decrease significantly. The thickness of the material layer under grinding elements will exceed the maximal height for which the particles are drawn under the grinding elements, causing excessive buildup of the material in front of the grinding elements. The material outflow from the bowl (or the bottom ring) is not supported by grinding elements movement, which results in higher flow resistance and uneven loading of the nozzle ring. These factors cause a significant decrease in mill efficiency.

Tests carried out for some industrial mills have proven that the change of grinding unit rotational speed strongly influences mill capacity. Therefore, by changing the gear ratio of the mill, both milling capacity and dynamic properties of the mill can be improved.

The fuel injector is designed to introduce the dispersed coal particles in a medium of air into the furnace. The mass ratio of air to coal is dependent on the coal mill manufacturer and usually ranges from 1.75 to 2.2 with a typical value of 2.0. An air to fuel mass ratio of 1.8 produces a primary stoichiometric ratio of approximately 0.16, or 16% of the air necessary for complete combustion of the coal. According to the previous discussion of NOx formation chemistry it is expected that lower NOx concentrations are achievable with lower primary gas/fuel ratios. The diameter of the coal transport line is constrained by the minimum velocity at which coal particles remain entrained in the carrier gas, or the coal layout velocity. This velocity is generally accepted to be 50 ft/s (Wall, 1987). The dimension of the fuel injector itself is selected by the burner manufacturer to provide the desired gas and particle velocity at the exit of the burner. The velocity here is anywhere from 50 to 115 ft/s and is chosen to provide the desired near flame aerodynamics impacting the mixing between the primary and secondary air. In many applications, there is an elbow, scroll or turning head in the coal pipe at the burner inlet. Such inlet devices result in roping, or an uneven distribution of coal within the fuel injector. Many manufacturers use components to redistribute the coal particles with an even density around the circumference of the fuel injector at its exit. A uniform distribution is typically desired to minimize NOx while maximizing combustion efficiency. The material of the fuel injector is chosen to be reliable under high temperatures and erosive conditions and is often a high grade of stainless steel. Another component of the fuel injector that is found on many commercial low NOx burners is a flame stabilizer. The function of this feature is to provide a stagnation zone at the fuel injector exit on the boundary between the primary and secondary air where small-scale mixing of coal and air occurs, providing ideal conditions for ignition and flame attachment.

Sulfur in coal can affect power plant performance in several ways. Sulfur in the form of pyrite (FeS2) can lead to spontaneous combustion and contributes to the abrasion in coal mills; therefore, if a lower quality coal containing pyrite is used in place of the design coal it can lead to problems. As the overall sulfur concentration increases, so do the emissions of sulfur dioxide (SO2) and sulfur trioxide (SO3). While the majority of the sulfur is converted to SO2 (about 12% of the sulfur converts to SO3), the increase in SO3 emissions increases the flue gas dew point temperature, which in turn can lead to corrosion issues. Most countries have legislation restricting SO2 emissions and utilizing higher sulfur coals will require additional SO2 controls (Miller, 2010). In some cases, the use of low quality fuels may impair the desulfurization equipment because of a greater quantity of flue gas to be treated (Carpenter, 1998).

All power stations require at least one CW pump and one 50% electric boiler feed pump available and running to start up a unit. In addition, fossil plant requires either coal mills or oil pumps and draught plant, e.g., FD and ID fans, PA fans, etc. Gas-cooled nuclear plant requires gas circulators running on main motors or pony motors at approximately 15% speed, whereas water reactors require reactor coolant pumps. Both nuclear types require various supporting auxiliaries to be available during the run-up stages, the poor quality steam being dumped until the correct quality is achieved.

When steam of correct quality is being produced, the turbine-generator will be run up to speed with all the unit supporting auxiliaries being powered from the station transformers via the unit/station interconnectors.

The Amer 9 plant utilizes both direct and indirect co-firing configurations. The plant co-fires biomass pellets up to a maximum of 1200ktyr1, generating 27% by heat through two modified coal mills. Only wood-based fuel has been used since 2006, due to reduced subsidies for agricultural by-products.

For the indirect co-firing option, low-quality demolition wood is gasified in a CFB gasifier at atmospheric pressure and a temperature of approximately 850C. The raw fuel gas is cleaned extensively and combusted in a coal boiler via specially designed low-CV gas burners. An advantage of this concept is that there is no contamination of the fuel gas as it enters the coal-fired boiler. This allows a wide range of fuels to be co-fired within existing emission constraints while avoiding problems with ash quality. The challenge, as always, is working within the relatively stringent fuel constraints while avoiding the inevitable high investment costs [22]. Amer 8 also co-fires at high biomass feed levels but uses a standard hammer mill configuration.

Coastal power stations, due to their proximity to major urban areas, tend to be better managed in terms of production consistency and environmental standards. In China and India in particular, coastal power stations tend to mill coal more finely, use superior emissions to control technologies, and have a tendency to use higher-quality coal blends. The result is higher quality and greater consistency in fly ash chemical and physical properties, to the extent that the material is more desirable to local cement manufacturers and those in other domestic markets along the coast. This material is typically allocated in multiyear contracts.

Adding to this, coastal urban areas usually have high volume demand for construction materials. Coastal power stations are often fully contracted to supply cement-grade fly ash, as well as the run of station ash and bottom ash to serve this demand. This is particularly clear in China, where coastal cities such as Shanghai and Shenzhen have seen dramatic urban development over the last 20years. During this period, both cities have been net importers of fly ash, drawing from both inland and domestic coastal sources.

The cost of loading material onto vessels, whether in containers or bulk, is much lower at coastal power stations due to lower local land transport costs. As a result, coastal power stations have been logical first choices for exporters/importers, and many have already developed either domestic coastal markets for their ash or export markets.

mrhs - mill reject handling system in thermal power plant

mrhs - mill reject handling system in thermal power plant

The function of Mill Rejects Handling system (MRHS) is to automatically discharge the iron pyrite and other nongrindable material from coal mill through an outlet connection to the reject conveying system.

Mill rejects will be led to respective pyrite hopper through mill rejects outlet spout and thereafter, it is further discharged to the transport vessel. Pneumatic conveying system has been envisaged for conveying of rejects from the transport vessel to mill reject silo.

For actuation and process air requirement in the system, instrument air will be provided at each stream through plant distribution instrument air pipe network from the specified tapping point to the pneumatic cylinder operated plate vales, bag filters, transport vessel and panels.

Necessary cooling water pipelines will be provided for cooling water requirements in dome valves and for quenching of mill rejects in pyrite hopper, whenever the temperature of the pyrite hopper exceeds desired levels. Service Water will be used for Quenching & Dome Cooling purpose. However cooling water requirement for conveying air compressor will be cater by DMCW water.

The pyrite hopper will be provided with one pneumatic cylinder operated plate valve on upstream which will be normally kept in open position. Grid will be provided in the hopper to prevent passage of oversize material to mill reject vessel.

One chain/manual operated plate valve will be provided to remove rejects collected on the grid manually. Pyrite hopper will be provided with bypass chute with cylinder operated plate type valve to unload the pyrite hoppers on the ground in case of emergency.

Pyrite hopper will be provided with manual operated plate valve on downstream side which is normally kept in open position, as it is a maintenance valve. Pyrite hopper will be provided with level probes and RTD. RF type level probe in the Pyrite hopper will pick up the signal when the hopper is full to a preset level. Arrangement of nozzles to spray water by operating the solenoid valve in the spray water line will be provided when temperature goes beyond the preset value.

Level probe in Pyrite hopper is set to pick up the signal when mill rejects reach a preset level in the hopper. Whenever such a signal is picked up by the probe, the inlet/ material handling valve is actuated to open and allow gravity feed of rejects into the Reject/transport vessel.

After lapse of predetermined time, the material handling/inlet valve closes and compressed air is injected through air inlet valve and the vessel gets pressurized. At predetermined pressure, the outlet valve of reject/transport vessel opens and rejects are conveyed to reject silo/storage bunker through pipeline.

As evacuation proceeds, vessel pressure drops and at a predetermined pressure, air inlet valve and outlet valve closes and the system gets ready for the next batch evacuation, commencement of which is signaled by level probe in the pyrite hopper.

The reject silo/storage bunker will be provided with adequately sized bag filter to vent the transport air to atmosphere, terminal boxes, level probe, Level Transmitter and pressure relief valve on the top of storage bunker. Manual operated discharge gate will be provided at outlet of storage bunker to unload the rejects into trucks. Clear height for truck shall be approx. 4.5 meter is provided.

The pneumatic cylinder operated plate valve at mill outlet (Pyrite Hopper inlet) is normally keptopen. Mill Rejects from coal mill will drop into the Pyrite Hopper through the grid. Oversize material will be retained on the grid. A pneumatic cylinder operated Plate Valve on oversize material discharge chute will be provided, which will be operated automatically in case of accumulation of oversized rejects.

Mill outlet valve will be closed when oversized rejects discharge outlet is opened. The High Level probe with switch in Pyrite Hopper will pick up when Pyrite Hopper is full or grid is choked. The emergency bypass chute will be fitted with a pneumatically operated plate valve and will be opened in case of emergency only.

Whenever the bypass valve is opened, it will be ensured that the Pyrite Hopper inlet valve is closed. The manually operated plate valve at Pyrite Hopper outlet will normally be kept in open position and will be closed for maintenance purpose only.

Each pneumatic cylinder operated Plate valve/gate valve of Pyrite Hopper shall be provided with open & close limit switch for indication in local and in OWS of DDCMIS. RTD with Temperature Transmitter in Pyrite Hopper will be provided, which will be set to generate annunciation in case the temperature goes beyond the set value and to open the Solenoid Valve in Spray Water line to spray water into the hopper.

In addition to probe mode, the quenching operation will also be provided with timer control.During normal operation, the Solenoid Valve on spray water line (normally closed) will be opened whenever dome valve is opened and water will be sprayed for quenching mill rejects in Pyrite Hopper for a short duration (adjustable between 5 to 10 Seconds).

Dome valve top plate will be provided with continuous cooling water supply to protect the insert seal through cooling water system sourced from service water system. Level probe with switch in Pyrite Hopper will be provided, which will be set to pick up when the mill rejects reach a preset level (high level or permissive level) generally kept equal to Vessel volume.

Whenever the level probe with switches pick up, the dome valve of the Conveying System Vessel will be actuated to open to allow gravity feed of mill rejects into the conveyor vessel. After a preset timelapse the dome valve will be closed, insert seal will be inflated through instrument air supply.

Compressed air from dense phase conveying airline will then be injected to convey the accumulated mill reject to the storage silo via pipe work. On completion, the vessel pressure will drop down to a preset value, which will be sense by Pressure switch and the system will be reset for next cycle commencement signaled by the Level probe with switch in Pyrite Hopper.

As a back up to this, a timer provision will also be made in the control system (including the water spraying online solenoid valve). The batch cycling operation and conveying of mill rejects goes on till high level in storage silo is sensed on which further conveying to bunker is stopped till bunker is evacuated. The mode of operation is same for all mills. Operation of all the pyrite hopper pneumatic conveying system is independent of each other.The Vessels will be in operation sequentially.

mill reject handling system. magaldi. | magaldi group

mill reject handling system. magaldi. | magaldi group

The MRS (Magaldi Mill Rejects System) is a new process concept designed to mechanically handle rejects from coal mills, in a dry way. Rejects are a mixture of different materials (pyrites, stones, tramp iron, etc.) with pulverized coal, requiring a reliable and safe removal system. Discharged from coal mills, the rejects are collected in pyrite boxes for temporary storage. The material is extracted from the pyrite boxes by MRS extracting conveyors or vibrating feeders and then dosed onto the main MRS conveyor, which collects the rejects produced by all the coal mills. Downstream the main MRS conveyor, the rejects can be discharged onto a movable container or into a storage silo. The MRS easily accommodates an increase in rejects and coal rate (for example during mill trip) without creating any fire or explosion hazard. In addition to the Superbelt technology, the MRS reliability is also guaranteed by the open execution design that allows:

Our website uses cookies to function correctly including third-party cookies. If you are interested in getting some more detailed information about the processing of personal data or about the use of cookies and how to block all or part of them, visit the following link: cookies. Accept / Close

mill rejects | jetpulsion pumps | united conveyor corporation | ucc

mill rejects | jetpulsion pumps | united conveyor corporation | ucc

With a comprehensive understanding of how the rejects vary from site to site and the specific needs of the plant for collection and disposal, UCC applies its extensive experience and laboratory testing to design and supply the proper system solution.

Sluice systems have been supplied for the majority of systems, especially when water is used for mill inerting, but pneumatic and mechanical systems have been used at a number of installations to minimize or eliminate water from the process.

United Conveyor Corporation (UCC) is a global leader in ash handling solutions for the power generation industry and a preferred supplier for dry sorbent injection, activated carbon injection and reagent handling.

Related News
  1. cylinder block grinding milling machine
  2. red mill flaxseed meal ground
  3. coal beneficiation equipment manufacturer in india
  4. dill grinding machine manufacher in gujarat
  5. coal mill in operation and maintenance manuals
  6. rp bowl mill parts suppliers in usa
  7. floor grinder rent lowes
  8. race powder with grinding machine
  9. powder grinding mill ave
  10. rubber powder mills and machines
  11. mobile cone mill operating principle
  12. high quality iron ore jaw crusher manufacturer in ukraine
  13. hot selling jaw crusher for iron ore
  14. vibrating screen manufacturer fine powder assam equipment
  15. feedercone crusher
  16. stone crusher at kanpur
  17. briquette fuel plant
  18. importance of gyratory ne mining mill
  19. power cost for beneficiation plant sand mining
  20. rubber grinder spiral