Hello, my partner! Let's explore the mining machine together!

[email protected]

flotation cell 5d

flotation cells

flotation cells

More ores are treated using froth flotation cells than by any other single machines or process. Non-metallics as well as metallics now being commercially recovered include gold, silver, copper, lead, zinc, iron, manganese, nickel, cobalt, molybdenum, graphite, phosphate, fluorspar, barite, feldspar and coal. Recent flotation research indicates that any two substances physically different, but associated, can be separated by flotation under proper conditions and with the correct machine and reagents. The DRflotation machine competes with Wemco and Outotec (post-outokumpu) flotation cells but are all similar is design. How do flotation cells and machinework for themineral processing industry will be better understood after you read on.

While many types of agitators and aerators will make a flotation froth and cause some separation, it is necessary to have flotation cells with the correct fundamental principles to attain high recoveries and produce a high grade concentrate. The Sub-A (Fahrenwald) Flotation Machines have continuously demonstrated their superiority through successful performance. The reliability and adaptations to all types of flotation problems account for the thousands of Sub-A Cells in plants treating many different materials in all parts of the world.

The design of Denver Sub-A flotation cells incorporates all of the basic principles and requirements of the art, in addition to those of the ideal flotation cell. Its design and construction are proved by universal acceptance and its supremacy is acknowledged by world-wide recognition and use.

1) Mixing and Aeration Zone:The pulp flows into the cell by gravity through the feed pipe, dropping directly on top of the rotating impeller below the stationary hood. As the pulp cascades over the impeller blades it is thrown outward and upward by the centrifugal force of the impeller. The space between the rotating blades of the impeller and the stationary hood permits part of the pulp to cascade over the impeller blades. This creates a positive suction through the ejector principle, drawing large and controlled quantities of air down the standpipe into the heart of the cell. This action thoroughly mixes the pulp and air, producing a live pulp thoroughly aerated with very small air bubbles. These exceedingly small, intimately diffused air bubbles support the largest number of mineral particles.

This thorough mixing of air, pulp and reagents accounts for the high metallurgical efficiency of the Sub-A (Fahrenwald) Flotation Machine, and its correct design, with precision manufacture, brings low horsepower and high capacity. Blowers are not needed, for sufficient air is introduced and controlled by the rotating impeller of the Denver Sub-A. In locating impeller below the stationary hood at the bottom of the cell, agitating and mixing is confined to this zone.

2) Separation Zone:In the central or separation zone the action is quite and cross currents are eliminated, thus preventing the dropping or knocking of the mineral load from the supporting air bubble, which is very important. In this zone, the mineral-laden air bubbles separate from the worthless gangue, and the middling product finds its way back into the agitation zone through the recirculation holes in the top of the stationary hood.

3) Concentrate Zone:In the concentrate or top zone, the material being enriched is partially separated by a baffle from the spitz or concentrate discharge side of the machine. The cell action at this point is very quiet and the mineral-laden concentrate moves forward and is quickly removed by the paddle shaft (note direct path of mineral). The final result is an unusually high grade concentrate, distinctive of the Sub-A Cell.

A flotation machine must not only float out the mineral value in a mixture of ground ore and water, but also must keep the pulp in circulation continuously from the feed end to the discharge end for the removal of the froth, and must give the maximum treatment positively to each particle.

It is an established fact that the mechanical method of circulating material is the most positive and economical, particularly where the impeller is below the pulp. A flotation machine must not only be able to circulate coarse material (encountered in every mill circuit), but also must recirculate and retreat the difficult middling products.

In the Denver Sub-A due to the distinctive gravity flow method of circulation, the rotating impeller thoroughly agitates and aerates the pulp and at the same time circulates this pulp upward in a straight line, removing the mineral froth and sending the remaining portion to the next cell in series. No short circuiting through the machine can thus occur, and this is most important, for the more treatments a particle gets, the greater the chances of its recovery. The gravity flow principle of circulation of Denver Sub-A Flotation Cell is clearly shown in the illustration below.

There are three distinctive advantages of theSub-A Fahrenwald Flotation Machines are found in no other machines. All of these advantages are needed to obtain successful flotation results, and these are:

Coarse Material Handled:Positive circulation from cell to cell is assured by the distinctive gravity flow principle of the Denver Sub-A. No short circuiting can occur. Even though the ore is ground fine to free the minerals, coarse materials occasionally gets into the circuit, and if the flotation machine does not have a positive gravity flow, choke-ups will occur.

In instances where successful metallurgy demands the handling of a dense pulp containing an unusually large amount of coarse material, a sand relief opening aids in the operation by removing from the lower part of the cell the coarser functions, directing these into the feed pipe and through the impeller of the flowing cell. The finer fraction pass over the weir overflow and thus receive a greater treatment time. In this manner short-circuiting is eliminated as the material which is bled through the sand relief opening again receives the positive action of the impeller and is subjected to the intense aeration and optimum flotation condition of each successive cell, floating out both fine and coarse mineral.

No Choke-Ups or Lost Time:A Sub-A flotation cell will not choke-up, even when material as coarse as is circulated, due to the feed and pulp always being on top of the impeller. After the shutdown it is not necessary to drain the machine. The stationary hood and the air standpipe during a shutdown protects the impeller from sanding-up and this keeps the feed and air pipes always open. Denver Sub-A flotation operators value its 24-hour per day service and its freedom from shutdowns.

This gravity flow principle of circulation has made possible the widespread phenomenal success of a flotation cell between the ball mill and classifier. The recovery of the mineral as coarse and as soon as possible in a high grade concentrate is now highly proclaimed and considered essential by all flotation operators.

Middlings Returned Without Pumps:Middling products can be returned by gravity from any cell to any other cell. This flexibility is possible without the aid of pumps or elevators. The pulp flows through a return feed pipe into any cell and falls directly on top of the impeller, assuring positive treatment and aeration of the middling product without impairing the action of the cell. The initial feed can also enter into the front or back of any cell through the return feed pipe.

Results : It is a positive fact that the application of these three exclusive Denver Sub-A advantages has increased profits from milling plants for many years by increasing recoveries, reducing reagent costs, making a higher grade concentrate, lowering tailings, increasing filter capacities, lowering moisture of filtered concentrate and giving the smelter a better product to handle.

Changes in mineralized ore bodies and in types of minerals quickly demonstrate the need of these distinctive and flexible Denver Sub-A advantages. They enable the treatment of either a fine or a coarse feed. The flowsheet can be changed so that any cell can be used as a rougher, cleaner, or recleaner cell, making a simplified flowsheet with the best extraction of mineral values.

The world-wide use of the Denver Sub-A (Fahrenwald) Flotation Machine and the constant repeat orders are the best testimonial of Denver Sub-A acceptance. There are now over 20,000 Denver Sub-A Cells in operation throughout the world.

There is no unit so rugged, nor so well built to meet the demands of the process, as the Denver Sub-A (Fahrenwald) Flotation Machine. The ruggedness of each cell is necessary to give long life and to meet the requirements of the process. Numerous competitive tests all over the world have conclusively proved the real worth of these cells to many mining operators who demand maximum result at the lower cost.

The location of the feed pipe and the stationary hood over the rotating impeller account for the simplicity of the Denver Sub-A cell construction. These parts eliminates swirling around the shaft and top of the impeller, reduce power load, and improve metallurgical results.

TheSub-A Operates in three zones: in bottom zone, impeller thoroughly mixes and aerates the pulp, the central zone separates the mineral laden particles from the worthless gangue, and in top zone the mineral laden concentrate high in grade, is quickly removed by the paddle of a Denver Sub-A Cell.

A Positive Cell Circulation is always present in theSub-A (Fahrenwald) Flotation Machine, the gravity flour method of circulating pulp is distinctive. There is no short circulating through the machine. Every Cell must give maximum treatment, as pulp falls on top of impeller and is aerated in each cell repeatedly. Note gravity flow from cell to cell.

Choke-Ups Are Eliminated in theSub-A Cell, even when material as coarse as is handled, due to the gravity flow principle of circulation. After shutdown it is not necessary to drain the machine, as the stationary hood protects impeller from sanding up. See illustration at left showing cell when shut down.

No Bowlers, noair under pressure is required as sufficient air is drawn down the standpipe. The expense and complication of blowers, air pipes and valves are thus eliminated. The standpipe is a vertical air to the heart of the Cell, the impeller. Blower air can be added if desired.

The Sub-A Flexibility allows it tobe used as a rougher, cleaner or recleaner. Rougher or middling product can be returned to the front or back of any cell by gravity without the use of pumps or elevators. Cells can be easily added when required. This flexibility is most important in operating flotation MILLS.

Pulp Level Is Controlled in each Sub-A Flotation Cell as it has an individual machine with its own pulp level control. Correct flotation requires this positive pulp level control to give best results in these Cells weir blocks are used, but handwheel controls can be furnished at a slight increase in cost. Note the weir control in each cell.

High Grade Concentrate caused by thequick removal of the mineral forth in the form of a concentrate increases the recovery. By having an adjustment paddle for each Sub-A Cell, quick removal of concentrate is assured, Note unit bearing housing for the impeller Shaft and Speed reducer drive which operates the paddle for each cell

Has Fewer Wearing Parts because Sub-A Cells are built for long, hard service, and parts subject to wear are easily replaced at low cost. Molded rubber wearing plates and impellers are light in weight give extra long life, and lower horsepower. These parts are made under exact Specifications and patented by Denver Equipment Co.

TheRugged Construction of theSub-A tank is made of heavy steel, and joints are welded both inside and out. The shaft assemblies are bolted to a heavy steel beam which is securely connected to the tank. Partition plates can be changed in the field for right or left hand machine. Right hand machine is standard.

The Minerals Separation or M.S. Sub-aeration cells, a section of which is shown in Fig. 32, consists essentially of a series of square cells with an impeller rotating on a vertical shaft in the bottom of each. In some machines the impeller is cruciform with the blades inclined at 45, the top being covered with a flat circular plate which is an integral part of the casting, but frequently an enclosed pump impeller is used with curved blades set at an angle of 45 and with a central intake on the underside ; both patterns are rotated so as to throw the pulp upwards. Two baffles are placed diagonally in each cell above the impeller to break up the swirl of the pulp and to confine the agitation to the lower zone. Sometimes the baffles are covered with a grid consisting of two or three layers each composed of narrow wood or iron strips spaced about an inch apart. The sides and bottom of the cells in the lower or agitation zone are protected from wear by liners, which are usually made of hard wood, but which can, if desired, consist of plates of cast-iron or hard rubber. The section directly under the impeller is covered with a circular cast-iron plate with a hole in the middle for the admission of pulp and air. The hole communicates with a horizontal transfer passage under the bottom liner, through which the pulp reaches the cell. Air is introduced into each cell through a pipe passing through the bottom and delivering its supply directly under the impeller. A low-pressure blower is provided with all machines except the smallest, of which the impeller speed is fast enough to draw in sufficient air by suction for normal requirements.

The pulp is fed to the first cell through a feed opening communicating with the transfer passage, along which it passes, until, at the far end, it is drawn up through the hole in the bottom liner by the suction of the impeller and is thrown outwards by its rotation into the lower zone. The square shape of the cell in conjunction with the baffles converts the swirl into a movement of intense agitation, which breaks up the air entering at the same time into a cloud of small bubbles, disseminating them through the pulp. The amount of aeration can be accurately regulated to suit the requirements of each cell by adjustment of the valve on its air pipe.

Contact between the bubbles and the mineral particles probably takes place chiefly in the lower zone. The pumping action of the impeller forces the aerated pulp continuously past the baffles into the upper and quieter part of the cell. Here the bubbles, loaded with mineral, rise more or less undisturbed, dropping out gangue particles mechanically entangled between them and catching on the way up a certain amount of mineral that has previously escaped contact. The recovery of the mineral in this way can be increased at the expense of the elimination of the gangue by increasing the amount of aeration. The froth collects at the top of the cell and is scraped by a revolving paddle over the lipat the side into the concentrate launder. The pulp, containing the gangue and any mineral particles not yet attached to bubbles, circulates to some extent through the zone of agitation, but eventually passes out through a slot situated at the back of the cell above the baffles and flows thence over the discharge weir. The height of the latter is regulated by strips of wood or iron and governs the level of the pulp in the cell. The discharge of each weir falls by gravity into the transfer passage under the next cell and is drawn up as before by the impeller. The pulp passes in this way through the whole machine until it is finally discharged as a tailing, the froth from each cell being drawn off into the appropriate concentrate launder.

No pipes are normally fitted for the transference of froth or other middling product back to the head of the machine or to any intermediate point. Should this be necessary, however, the material can be taken by gravity to the required cell through a pipe, which is bent at its lower end to pass under the bottom liner and project into the transfer passage, thus delivering its product into the stream of pulp that is being drawn up by the impeller

Particulars of the various sizes of M.S. Machines are given in Table 21. It should be noted that the size of a machine is usually defined by the diameter of its impeller ; for instance, the largest one would be described as a 24-inch machine.

The Sub-A Machine, invented by A. W. Fahrenwald and developed in many respects as an improvement in the Minerals Separation Machine, from which it differs considerably in detail, particularly in the method of aerating the pulp, although the principle of its action is essentially the same. Its construction can be seen from Figs. 33 and 34.

In common with the M.S. type of machine, it consists of a series of square cells fitted with rotating impellers. Each cell, however, is of unit construction, a complete machine being built up by mounting the required number of units on a common foundation and connecting up the pipes which transfer the pulp from one cell to the next. The cells are constructed of welded steel. The impeller, which can be rubber-lined,if required, carries six blades set upright on a circular dished disc, and is securely fixed to the lower end of the vertical driving shaft. It is covered with a stationary hood, to which are attached a stand-pipe, a feed pipe, and the middling return pipes. The underside of the hood is fitted with a renewable liner of rubber or cast-iron. The pulp, entering the first cell through the feed pipe and sometimes through the middling pipes, falls on to the impeller, the rotation of which throws it outwards into the bottom zone of agitation. The suction effect due to the rotationof the impeller draws enough air down the standpipe to supply the aeration necessary for normal operation. A portion of the pulp, cascading over the open tops of the impeller blades, entraps and breaks up the entrained air, the resulting spray-like mixture being then thrown out into the lower zone of agitation, where it is disseminated through the pulp as a cloud of fine bubbles. Should this amount of aeration be insufficient, air can be blown in under slight pressure through a hole near the top of the stand-pipe, in which case a rubber bonnet is fastenedto the lower bearing and clamped round the top of the stand-pipe so as to seal the supply from the atmosphere.

The bottom part of the cell is protected from wear by renewable cast-iron or rubber liners. Four vertical baffles, placed diagonally on the top of the hood, break up the swirl of the pulp and intensify theagitation in the lower zone. The pumping action of the impeller combined with the rising current of air bubbles carries the pulp to the quieter upper zone, where the bubbles, already coated with mineral, travel upwards, drop out many of the gangue particles which may have become entangled with them, and finally collect on the surface of the pulp as a mineralizedfroth. One side of the cell is sloped outwards so as to form, in conjunction with a vertical baffle, a spitzkasten-shaped zone of quiet settlement, where any remaining particles of gangue that have been caught and held between the bubbles are shaken out of the froth as it flows to the overflow lip at the front of the cell. The baffle prevents rising bubbles from entering the outer zone, thus enabling the gangue material released from the froth to drop down unhindered into the lower zone. A revolving paddle scrapes the froth past the overflow lip into the concentrate launder.

Should the machine be required to handle more than the normal volume of froth, it is built with a spitzkasten zone on both sides of the cell. For the flotation of ores containing very little mineral the spitzkasten is omitted so as to crowd the froth into the smallest possible space, the front of the cell being made vertical for the purpose.

Circulation of the pulp through the lower zone of agitation is maintained by means of extra holes at the base of the stand-pipe on a level with the middling return pipes. An adjustable weir provides for the discharge of the pulp to the next cell, which it enters through a feed-pipe as before. Below the weir on a level with the hood is a small sand holeand pipe through which coarse material can pass direct to the next cell without having to be forced up over the weir. The same process is repeated in each cell of the series, the froth being scraped over the lip of the machine, while the pulp passes from cell to cell until it is finally discharged as a tailing from the last one. The middling pipes make it an easy matter for froth from any section of the machine to be returned if necessary to any cell without the use of pumps.

Table 22 gives particulars of the sizes and power requirements of Denver Sub-A Machines and Table 23 is an approximate guide to their capacities under different conditions. The number of cells needed

Onemethod of driving the vertical impeller shafts of M.S. Subaeration or Denver Sub-A Machines is by quarter-twist belts from a horizontal lineshaft at the back of the machine, the lineshaft being driven in turn by a belt from a motor on the ground. This method is not very satisfactory according to modern standards, firstly, because the belts are liable to stretch and slip off, and, secondly, because adequate protection againstaccidents due to the belts breaking is difficult to provide without making the belts themselves inaccessible. A more satisfactory drive, with which most M.S. Machines are equipped, consists of a lineshaft over the top of the cells from which each impeller is driven through bevel gears. The lineshaft can be driven by a belt from a motor on the ground, by Tex- ropes from one mounted on the frame work of the machine, or by direct coupling to a slow-speed motor. This overhead gear drive needs careful adjustment and maintenance. Although it may run satisfactorily for years, trouble has been experienced at times, generally in plants where skilled mechanics have not been available. The demand for something more easily adjusted led to the development of a special form of Tex-rope drive which is shown in Fig. 35. Every impeller shaft is fitted at the top with a grooved pulley, which is driven by Tex-ropes from a vertical motor. This method is standard on Denver Sub-A Machines, and M.S. Machines are frequently equipped with it as well, but the former type are not made with the overhead gear drive except to special order.

The great advantage of mechanically agitated machines is that every cell can be regulated separately, and that reagents can be added when necessary at any one of them. Since, as a general rule, the most highly flocculated mineral will become attached to a bubble in preference to a less floatable particle, in normal operation the aeration in the first few cells of a machine should not be excessive ; theoretically there should be no more bubbles in the pulp than are needed to bring up the valuable minerals. By careful control of aeration it should be possible for the bulk of the minerals to be taken off the first few cells at the feed end of the machine in a concentrate rich enough to be easily cleaned, and sometimes of high enough grade to be sent straight to the filtering section as a finished product. The level of the pulp in these cells is usually kept comparatively low in order to provide a layer of froth deep enough to give entangled particles of gangue every chance of dropping out, but it must not be so low that the paddles are prevented from skimming off the whole of the top layer of rich mineral. Towards the end of the machine a scavenging action is necessary to make certain that the least possible amount of valuable mineral escapes in the tailing, for which purpose the gates of the discharge weirs are raised higher than at the feed end, and the amountof aeration may have to be increased. The froth from the scavenging cells is usually returned to the head of the machine, the middling pipes of the Denver Sub-A Machine being specially designed for such a purpose. The regulation of the cleaning cells is much the same as that of the first few cells of the primary or roughing machine, to the head of which the tailing from the last of the cleaning cells is usually returned.

A blower is sometimes required with the M.S. Subaeration Machine. Since each cell is fitted with an air pipe and valve, accurate regulation of aeration is a simple matter. The Denver Sub-A, Kraut, and Fagergren Machines, however, are run without blowers, enough air being drawn into the machines by suction.

In the Geco New-Cell Flotation Cellthe pneumatic principle is utilized in conjunction with an agitating device. The machine, which is illustrated in Fig. 44, consists of a trough or cell made of steel or wood, whichever is more convenient, through the bottom of which projects a series of air pipes fitted with circular mats of perforated rubber. The method of securing the mat to the air pipe can be seen from Fig. 45. Over each mat rotates a moulded rubber disc of slightlylarger diameter at a peripheral speed of 2,500 ft. per minute. It is mounted on a driving spindle as shown in Fig. 46. Each spindle is supported and aligned by ball-bearings contained in a single dust- and dirt-proof casting, and each pair is driven from a vertical motor through Tex-ropes and grooved pulleys, a rigid steel structure supporting the whole series of spindles with their driving mechanism. The machine can be supplied, if required, however, with a quarter-twist drive from a lineshaft over flat pulleys.

The air inlet pipes are connected to a main through a valve by which the amount of air admitted to each mat can be accurately controlled. The air is supplied by a low-pressure blower working at about 2 lb. per square inch. It enters the cell through the perforations in the rubber mat and is split up into a stream of minute bubbles, which are distributed evenly throughout the pulp by the action of the revolving disc. By this means a large volume of finely-dispersed air is introduced withoutexcessive agitation. There is sufficient agitation, however, to produce a proper circulation in the cell, but not enough to cause any tendency to surge or to disturb the froth on the surface of the pulp. All swirling movement is checked by the liner-baffles with which the sides of the cell are lined ; their construction can be seen in Fig. 44. They are constructed of white cast iron and are designed to last the life of the machine, the absence of violent agitation making this possible.The pulp must be properly conditioned before entering the machine. It is admitted through a feed box at one end at a point above the first disc, and passes along the length of the cell to the discharge weir without being made to pass over intermediate weirs between the discs. The height of the weir at the discharge end thus controls the level of the pulp in the machine. The froth that forms on the surface overflows the froth lip in a continuous stream without the aid of scrapers, its depth being controlled at any point by means of adjustable lip strips combined with regulation of the air.The Geco New-Cell is made in four sizesviz., 18-, 24-, 36-, and 48-in. machines, the figure representing the length of the side of the squarecell. Particulars of the three smallest sizes are given in Table 27. Figures are not available for the largest size.

different types of flotation cells

different types of flotation cells

Flotation is both a science and an art. It brings together many complex variables. Such basic factors as knowledge of mineral structure, chemical reagents, pH of mill water, pulp density, temperature, technical skills of the operator, the dependability of the flotation machine, as well as a host of other factors which affect the flotation of each specific ore must be combined to produce economic metallurgy. Economic Metallurgy is the practical objective of all mineral processing that of securing the greatest possible profit from the operation. It incorporates the elements of greatest possible recovery, highest possible grade of concentrates, lowest possible milling, capital, operating and maintenance costs.

In 1961 the American Institute of Mining and Metallurgical Engineers commemorated the 50th Anniversary of Flotation in the U.S.A. with a special 700- page documentary report. The book, Froth Flotation, 50th Anniversary Volume, highlights some of the many changes to flotation machines that have taken place since the first flotation cells in the United States went on stream in 1911 at Basin, Montana.

In 1911 the only mineral recovered by flotation was sphalerite. However, today flotation is the principal method of mineral processing throughout the world. Capacity of the first flotation mill was only 50 tons of ore per day. Now more than 100 different minerals are commercially recovered by flotation and some mills process as much as 50,000 tons of ore every 24 hours.

One of the significant changes made to reduce operating costs has been the extensive use of pressure molded rubber parts to withstand abrasion and thus reduce maintenance. Design of flotation cells has been improved and simplified to handle increased tonnage. One such development was the free-flow tank design. Another change has been the use of flotation mechanisms which can be removed from the flotation machine quickly for the inspection or change of wearing parts. A simple change in the method of pre-mixing air with pulp as it enters the throat of the flotation impeller has made it possible to reduce power cost as much as 50%. Development of larger flotation cells means fewer flotation cells are needed to do the job. This simplifies maintenance and reduces construction costs.

The cell-to-cell flotation machine meets the needs for both mineral recovery and cleaning and recleaning of flotation concentrates. It incorporates simplicity and flexibility of adjustment that permits the flotation operator to use his skill in securing the exact flotation conditions required by his specific ore for economic metallurgy.

The cell-to-cell flotation machine is typified by a flotation mechanism suspended in an individual cell separated from the adjoining cells by an adjustable weir. A feed pipe conducts the flow of pulp from the weir of the preceding cell to the mechanism.

Cell-to-cell Flotation Mechanism showing how feed pipe conducts pulp to throat of the rotating impeller. Each cell has its own mechanism, adjustable overflow weirs and feed pipe. Molded rubber wearing parts are used. Free-Flow Flotation Mechanism showing how the pulp flows through the machine without interruption of weirs. Feed pipes are not used. Pulp enters the throat of the rotating impeller by flowing down the outer feed well. Air, under low pressure, is pre-mixed with the pulp and is thoroughly diffusedthroughout the cell by intense action of the impeller.

A typical modern fluorspar mill where cell-to-cell Flotation Machines are used to clean and reclean fluorspar concentrates to meet market specifications for acid-grade fluorspar. Note pipes on launders return froth for multiple cleaning without need for pumps.

Early-day Sub-A Flotation Machine. Note the wood tank and flat-belt drive. Machines of this type were used in the 1920s and 1930s. They were the principal type of flotation machine used throughout the world. Experience and continual improvement are behind modern Flotation Cells.

The need for a flotation machine to handle larger tonnages in bulk flotation circuits led to the development of the Free-Flow type flotation machine. These units are characterized by the absence of intermediate partitions or weirs between cells. Individual cell feed pipes have been eliminated. Pulp is free to flow through the machine without interference. Flotation efficiency is high, operation is simple and the need for operator attention is minimized. Most high tonnage mills today use the free-flow type of flotation machine. Many are equipped with automatic devices for control of pulp density, pulp level, and other variable factors.

Just as modern flotation machines have evolved from the past they will change to meet future needs of the industry. Larger, more efficient flotation cells, automatic control of grinding circuits, flow meters, continuous on-stream sampling, direct reading density, pH, and pulp level devices, new reagents as well as instantaneous X-ray analysis will make possible almost completely automated flotation circuits and new achievements in economic metallurgy.

flotation cell - an overview | sciencedirect topics

flotation cell - an overview | sciencedirect topics

The MAC flotation cell was developed by Kadant-Lamort Inc. It can save energy comparedto conventional flotation systems. The MAC flotation cell is mainly used in the flotation section of waste paper deinking pulping, for removal of hydrophobic impurities such as filler, ash,ink particles, etc. It can increase pulp whiteness and meet the requirements of final paper appearance quality. Table11.11 shows the features of MAC flotation cell. Kadants MAC flotation cell deinking system uses air bubbles to float ink particles to the cell surface for removal from the recycled material. The latest generation of the MAC cell deinking system incorporates a patented bubble-washing process to reduce power consumption and also fiber loss. It combines small, new, auto-clean, low-pressure injectors with a flotation cell. The function of injectors is to aerate the stock before it is pumped and sent tangentially to the top of the cell. The air bubbles collect ink particles in the cell and rise up to the top to create a thick foam mat that is evacuated because of the slight pressurization of the cell. The partially deinked stock then goes to a deaeration chamber and is pumped to the next stage. Here, the operation is exactly the same as for the first stage. This stage also has the same number of injectors and same flow (Kadant,2011). This operation is repeated up to five times for a high ink removal rate. Remixing of the air coming from downstream stages of the process helps the upstream stages and improves the overall cell efficiency. Adjustable and selective losses of fiberdepend on the application and technical requirements inks, or inks and fillers. The use of low-pressure injectors in the MAC flotation cell could save about 2530% of the energy used in conventional flotation systems (ECOTARGET,2009). The benefits of the MAC flotation cell are summarized in Table11.12.

Agitated flotation cells are widely used in the mineral processing industry for separating, recovering, and concentrating valuable particulate material from undesired gangue. Their performance is lowered, however, when part of the particulate system consists of fines, with particle diameters typically in the range from 30 to 100m. For example, it was observed difficult to float fine particles because of the reduction of middle particles (of wolframite) as carriers and the poor collision and attachment between fine particles and air bubbles; a new kinetic model was proposed [34].

As an alternative to agitated cells, bubble columnsused in chemical engineering practice as chemical reactorswere proposed for the treatment of fine particle systems. Flotation columns, as they came to be known, were invented back in the 1960s in Canada [35]. The main feature that differentiates the column from the mechanical flotation cell (of Denver type) is wash water, added at the top of the froth. It was thought to be beneficial to overall column performance since it helps clean the froth from any entrained gangue, while at the same time preventing water from the pulp flowing into the concentrate. In this way, it was hoped that certain cleaning flotation stages could be gained.

Let us note that the perhaps insistence here on mineral processing is only due to the fact that most of the available literature on flotation is from this area, where the process was originated and being widely practiced. The effect of particle size on flotation recovery is significant; it was shown that there exists a certain size range in which optimum results may be obtained in mineral processing. This range varies with the mineral properties such as density, liberation, and so on, but was said to be of the order of 10100m [36].

Regulating the oxidation state of pyrite (FeS2) and arsenopyrite (FeAsS), by the addition of an oxidation or reduction chemical agent and due to the application of a short-chain xanthate as collector (such as potassium ethyl xanthate, KEX), was the key to selective separation of the two sulfide minerals, pyrite and arsenopyrite [37]. Strong oxidizing agents can depress previously floated arsenopyrite. Various reagents were examined separately as modifiers and among them were sodium metabisulfite, hydrazinium sulfate, and magnesia mixture. The laboratory experiments were carried out in a modified Hallimond tube, assisted by zeta-potential measurements and, in certain cases, by contact angle measurements.

This conventional bench-scale flotation cell provides a fast, convenient, and low-cost method, based on small samples (around 2g), usually of pure minerals and also artificial mixtures, for determining the general conditions under which minerals may be rendered floatableoften in the absence of a frother (to collect the concentrate in the side tube) [38]. This idea was later further modified in the lab replacing the diaphragm, in order to conduct dissolved air or electroflotation testssee Section 3.

Pyrite concentrates sometimes contain considerable amounts of arsenic. Since they are usually used for the production of sulfuric acid, this is undesirable from the environmental point of view. However, gold is often associated with arsenopyrite, often exhibiting a direct relationship between Au content and As grade. There is, therefore, some scope for concentrating arsenopyrite since the ore itself is otherwise of little value (see Fig.2.2). Note that previous work on pyrites usually concentrated on the problem of floating pyrite [40].

In the aforementioned figure (shown as example), the following conditions were applied: (1) collector [2-coco 2-methyl ammonium chloride] 42mg/L, frother (EtOH) 0.15% (v/v), superficial liquid velocity uL=1.02cm/s, superficial gas velocity uG=0.65cm/s, superficial wash water velocity uw=0.53cm/s; (2) hexadecylamine, 45mg/L; pine oil, 50mg/L; EtOH, 0.025%; uL=0.84cm/s; uG=0.72cm/s; uw=0.66cm/s; (3) Armoflot 43, 50mg/L; pine oil, 50mg/L; EtOH, 0.025%; uL=0.84cm/s; uG=0.71cm/s; uw=0.66cm/s [39]. The pyrite (with a relatively important Au content of 21g/ton) was a xanthate-floated concentrate. The presence of xanthates, however, might cause problems in the subsequent cyanidation of pyrites when recovering their Au value, which perhaps justified the need to find alternative collectors. In general, the amines exhibited a behavior similar to that of the xanthates (O-alkyl dithiocarbonates). The benefit of the amine was in its lower consumption, as compared with the xanthate systems.

The arsenic content of the pyrite was approximately 9% (from an initial 3.5% of the mixed sulfide ore). The material was sieved and the75m fraction was used for the laboratory-scale cylindrical column experiments. The effect on metallurgical characteristics of the flotation concentrate of varying the amount of ferric sulfate added to the pulp was studied; three collectors were used and their performance was compared (in Fig.2.2). Both hexadecylamine and Armoflot 43 (manufactured by Akzo) exhibited an increased recovery but a very low enrichment, whereas 2-coco 2-methyl ammonium chloride (Arquad-2C) showed a considerable enrichment; a compromise had to be made, therefore, between a high-grade and a low recovery.

Electroflotation (electrolytic flotation) is an unconventional separation process owing its name to the bubbles generation method it uses, i.e., electrolysis of the aqueous medium. In the bottom of the microcell, the two horizontal electrodes were made from stainless steel, the upper one being perforated. The current density applied was 300 Am2. It was observed that with lime used to control pH, different behavior was observed (see Fig.2.3). Pyrite, with permanganate (a known depressant) also as modifier, remained activated from pH 5.0 to 8.0at 80% recovery, while it was depressed at the pH range from 9.0 to 12.0. A conditioning of 30min was applied in the presence of modifier alone and further 15min after the addition of xanthate. The pure mineral sample, previously hand collected, crushed, and pulverized in the laboratory, was separated by wet sieving to the45 to+25m particle size range.

Pyrite due to its very heterogeneous surface, consisting of a mosaic of anodic and cathodic areas, presents a strong electrocatalytic activity in the anodic oxidation of xanthate to dixanthogen. It is also possible that the presence of the electric field, during electroflotation, affected the reactions taking place. In order to explain this difference in flotation behavior thermodynamic calculations for the system Fe-EX-H2O have been done [41]. It was concluded that electroflotation was capable of removing fine pyrite particles from a dilute dispersion, under controlled conditions. Nevertheless, dispersed air and electroflotation presented apparent differences for the same application.

The size of the gas bubbles produced was of the order of 50m, in diameter [21]. Similar measurements were later carried out at Newcastle, Australia [42]; where it was also noted that a feature of electroflotation is the ability to create very fine bubbles, which are known to improve flotation performance of fine particles.

In fact, the two electrodes of a horizontal electrodes set, usually applied in electroflotation, could be separated by a cation exchange membrane, as only one of the produced gases is often necessary [43]. In the lower part/separated electrode, an electrolyte was circulated to remove the created gas, and in the meantime, increase the conductivity; hence having power savings (as the electric field is built up between the electrodes through the use of the suspension conductivity). Attention should be paid in this case to anode corrosion, mainly by the chloride ion (i.e., seawater).

Microorganisms have a tremendous influence on their environment through the transfer of energy, charge, and materials across a complex biotic mineralsolution interface; the biomodification of mineral surfaces involves the complex action of microorganism on the mineral surface [44]. Mixed cationic/anionic surfactants are also generating increasing attention as effective collectors during the flotation of valuable minerals (i.e., muscovite, feldspar, and spodumene ores); the depression mechanisms on gangue minerals, such as quartz, were focused [45].

Another design of a flotation cell which applies ultrasound during the flotation process has been developed by Vargas-Hernndez et al. (2002). The design consists of a Denver cell (Koh and Schwarz, 2006) equipped with ultrasonic capabilities of performing ultrasound-assisted flotation experiments. This cell is universally accepted as a standard cell for laboratory flotation experiments. In Figure 35.25, a schematic of the Denver cell equipped with two power transducers is shown operating at 20kHz. The ultrasonic transducers are in acoustic contact with the body of the flotation cell but are not immersed in the same cell. Instead, they are submerged in distilled water and in a thin membrane that separates the radiant head of the transducer from the chamber body. The floatation chamber has a capacity of 2.7l and is also equipped with conventional systems to introduce air and mechanical agitation able to maintain the suspension of metallurgical pulp. In the upper part of the cell there is an area in which the foam is recovered for analysis by a process called skimming. The block diagram of Figure 35.25 further shows that the experimental system was developed to do ultrasonic-assisted flotation experiments. The transducers operate at 20kHz and can handle power up to 400W. In the Denver cell an acoustic probe, calibrated through a nonlinear system and capable of measuring high-intensity acoustic fields, is placed (Gaete-Garretn et al., 1993, 1998). This is done in order to determine the different acoustic field intensities with a spatial scanner during the experimentation. Figure 35.26 shows the distribution of ultrasonic field intensity obtained by a spatial scanner in the central area of the flotation chamber. The Denver cell with ultrasonic capabilities, as described, is shown in Figure 35.27. The obtained results were fairly positive. For example, for fine particle recovery it worked with metallurgical pulp under 325mesh, indicating floating particles of less than 45m, and the recovery curves are almost identical to those of an appropriate size mineral for flotation. This is shown in Figure 35.28, where a comparison between typical copper recovery curves for fine and normal particles is presented. The most interesting part of the flotation curves is the increase in recovery of molybdenum with ultrasonic power, as shown in Figure 35.29. The increase in recovery of iron is not good news for copper mines because the more iron floating the lower grade of recovery. This may be because the iron becomes more hydrophobic with ultrasonic action. According to the experts, this situation could be remedied by looking for specific additives to avoid this effect. Flotation kinetics shown in Figure 35.30 with 5 and 10W of acoustic power applied also show an excellent performance. It should be noted that the acoustic powers used to vary the flotation kinetics have been quite low and could clearly be expanded.

Figure 35.28. Compared recovering percent versus applied power in an ultrasonic-assisted flotation process in a Denver cell: (a) fine and ultrafine particles recovering and (b) normal particles recovering.

These experiments confirm the potential of power ultrasound in flotation. Research on assisted flotation with power ultrasound has been also carried out by Ozkan (2002), who has conducted experiments by pretreating pulp with ultrasound during flotation. Ozkhans objective was to recover magnesite from magnesite silts with particles smaller than 38m. Their results show that under ultrasonic fields the flotation foam bubbles are smaller, improving magnesite recovery rates. When Ozkhan treated magnesite mineral with a conventional treatment the beneficial effect of ultrasound was only manifested for mineral pretreatment. The flotation performed under ultrasonic field did not show improvement. This was because power ultrasound improves the buoyancy of clay iron and this has the effect of lowering the recovery of magnesite.

Kyllnen et al. (2004) employed a cell similar to Jordan to float heavy metals from contaminated soils in a continuous process. In their experiments they obtained a high recovery of heavy metals, improving the soil treatment process. Alp et al. (2004) have employed ultrasonic waves in the flotation of tincal minerals (borax Na O710 B4 H2O), finding the same effects as described above, i.e., that power ultrasound helps in the depression of clay. However, the beneficial effect of ultrasound is weakened when working with pulps with high mineral concentration (high density), probably due to an increase in the attenuation of the ultrasonic field. Safak and Halit (2006) investigated the action mechanisms of ultrasound under different flotation conditions. A cleaning effect on the floating particles was attributed to the ultrasonic energy, making the particles more reactive to the additives put in the metallurgical pulp. Furthermore due to the fact that the solid liquid interface is weaker than the cohesive forces of the metallurgic pulp liquids, it results in a medium favorable to creation of cavitation bubbles. The unstable conditions of a cavitation environment can produce changes in the collectors and even form emulsions when entering the surfactant additives. In general, many good properties are attributed to the application of ultrasound in flotation. For example, there is a more uniform distribution of the additives (reagents) and an increase in their activity. In fact in the case of carbon flotation it has been found that the floating times are shortened by the action of ultrasound, the bubble sizes are more stable, and the consumption of the reagents is drastically lowered.

Abrego Lpez (2006) studied a water recovery process of sludge from industrial plants. For this purpose he employed a flotation cell assisted by power ultrasound. In the first stage he made a flotation to recover heavy metals in the metallurgical pulp, obtaining a high level of recovery. In the second stage he added eucalyptus wood cones to the metallurgical pulp to act as an accumulator of copper, lead, nickel, iron, and aluminum. The author patented the method, claiming that it obtained an excellent recovery of all elements needing to be extracted. zkan and Kuyumcu (2007) showed some design principles for experimental flotation cells, proposing to equip a Denver flotation cell with four power transducers. Tests performed with this equipment consisted of evaluating the possible effects that high-intensity ultrasonic fields generated in the cell may have on the flotation. The author provides three-dimensional curves of ultrasonic cavitation fields in a Denver cell filled with water at frequencies between 25 and 40kHz. A warming effect was found, as expected. However, he states that this effect does not disturb the carbon recovery processes because carbon flotation rarely exceeds 5min. They also found that the pH of tap water increases with the power and time of application of ultrasound, while the pH of the carbonwaterreagentsludge mixture decreases. The conductivity of the metallurgical pulp grows with the power and time of application of ultrasound, but this does not affect flotation. The carbon quality obtained does not fall due to the application of ultrasound and the consumption of lowered reagents. They did not find an influence from the ultrasound frequency used in the process, between 25 and 40kHz. They affirmed that ultrasound is beneficial at all stages of concentration.

Kang et al. (2009) studied the effects of preconditioning of carbon mineral pulp in nature by ultrasound with a lot of sulfur content. They found that the nascent oxygen caused by cavitation produces pyrite over oxidation, lowering its hydrophobicity, with the same effect on the change of pH induced by ultrasonic treatment. Additionally, ultrasound decreases the liquid gas interfacial tension by increasing the number of bubbles. Similar effects occur in carbon particles. The perfect flotation index increases 25% with ultrasonic treatment. Kang et al. (2008) continued their efforts to understand the mechanism that causes effects in ultrasonic flotation, analyzing the floating particles under an ultrasonic field by different techniques like X-ray diffraction, electron microscopy, and scanning electron microscopy techniques. In carbon flotation it is estimated that ultrasonic preconditioning may contribute to desulfurization and ash removal (deashing) in carbon minerals. Zhou et al. (2009) have investigated the role of cavitation bubbles created by hydrodynamic cavitation in a flotation process, finding similar results to those reported for ultrasonic cavitation flotation. Finally, Ozkan (2012) has conducted flotation experiments with the presence of hard carbon sludge cavitation (slimes), encountering many of the effects that have been reported for the case of metallurgical pulp with ultrasound pretreatment. This includes improved flotation, drastic reduction in reagent consumption, and the possible prevention of oxidation of the surface of carbon sludge. A decrease in the ash content in floating carbon was not detected. However, tailings do not seem to contain carbon particles. All these effects can be attributed to acoustic cavitation. However, according to the author, there is a need to examine the contribution of ultrasound to the probability of particlebubble collision and the likelihood of getting the bubbles to connect to the particles. The latter effects have been proposed as causes for improvements in flotation processes in many of the publications reviewed, but there is no systematic study of this aspect.

In summary, power ultrasound assistance with flotation processes shows promising results in all versions of this technique, including conditioning metallurgical pulp before floating it, assisting the continuous flotation process, and improving the yields in conventional flotation cells. The results of ultrasonic floating invariably show a better selectivity and an increase, sometimes considerable, in the recovery of fine particles. Paradoxically, in many experiments an increase has been recorded in recovering particles suitable for normal flotation. These facts show the need for further research in the flotation process in almost all cases, with the exception perhaps of carbon flotation. For this last case, in light of the existing data the research should be directed toward scale-up of the technology.

The concentrate obtained from a batch flotation cell changes in character with time as the particles floating change in size, grade and quantity. In the same way, the concentrate from the last few cells in a continuous bank is different from that removed from the earlier cells. Particles of the same mineral float at different rates due to different particle characteristics and cell conditions.

The recovery of any particular mineral rises to an asymptotic value R which is generally less than 100%. The rate of recovery at time t is given by the slope of the tangent to the curve at t, and the rate of recovery at time t1 is clearly greater than the rate at time t2. There is a direct relationship between the rate of flotation and the amount of floatable material remaining in the cell, that is:

The process is carried out in a flotation cell or tank, of which there are two basic types, mechanical and pneumatic. Within each of these categories, there are two subtypes, those that operate as a single cell, and those that are operated as a series or bank of cells. A bank of cells (Fig. 8) is preferred because this makes the overall residence times more uniform (i.e., more like plug flow), rather than the highly diverse residence times that occur in a single (perfectly mixed) tank.

FIGURE 8. Flotation section of a 80,000t/d concentrating plant, showing the arrangement of the flotation cells into banks. A small part of the grinding section can be seen through the gap in the wall. [Courtesy Joy Manufacturing Co.]

The purpose of the flotation cell is to attach hydrophobic particles to air bubbles, so that they can float to the surface, form a froth, and can be removed. To do this, a flotation machine must maintain the particles in suspension, generate and disperse air bubbles, promote bubbleparticle collision, minimize bypass and dead spaces, minimize mechanical passage of particles to the froth, and have sufficient froth depth to allow nonhydrophobic (hydrophilic) particles to return to the suspension.

Pneumatic cells have no mechanical components in the cell. Agitation is generally by the inflow of air and/or slurry, and air bubbles are usually introduced by an injector. Until comparatively recently, their use was very restricted. However, the development of column flotation has seen a resurgence of this type of cell in a wider, but still restricted, range of applications. While the total volume of cell is still of the same order as that of a conventional mechanical cell, the floor space and energy requirements are substantially reduced. But the main advantage is that the cell provides superior countercurrent flow to that obtained in a traditional circuit (see Fig. 11), and so they are now often used as cleaning units.

Mechanical cells usually consist of long troughs with a series of mechanisms. Although the design details of the mechanisms vary from manufacturer to manufacturer, all consist of an impeller that rotates within baffles. Air is drawn or pumped down a central shaft and is dispersed by the impeller. Cells also vary in profile, degree of baffling, the extent of walling between mechanisms, and the discharge of froth from the top of the cell.

Selection of equipment is based on performance (represented by grade and recovery), capacity (metric tons per hour per cubic meter); costs (including capital, power, maintenance), and subjective factors.

Among all processing industries, only in the ore and mining industries is the accent more on wear resistance than corrosion. In mining industries, the process concerns material handling more than any physical or chemical conversions that take place during the refining operations. For example, in the excavation process of iron ore, conventional conveyer systems and sophisticated fluidized systems are both used [16,17]. In all these industries, cost and safety are the governing factors. In a fluidized system, the particles are transported as slurry using screw pumps through large pipes. These pipes and connected fittings are subjected to constant wear by the slurry containing hard minerals. Sometimes, depending on the accessibility of the mineral source, elaborate piping systems will be laid. As a high-output industry any disruption in the work will result in heavy budgetary deficiency. Antiabrasive rubber linings greatly enhance the life of equipment and reduce the maintenance cost. The scope for antiabrasive rubber lining is tremendous and the demand is ever increasing in these industries.

Different rubber compounds are used in the manufacture of flotation cell rubber components for various corrosion and abrasion duty conditions. Flotation as applied to mineral processing is a process of concentration of finely divided ores in which the valuable and worthless minerals are completely separated from each other. Concentration takes place from the adhesion of some species of solids to air bubbles and wetting of the other series of solids by water. The solids adhering to air bubbles float on the surface of the pulp because of a decrease in effective density caused by such adhesion, whereas those solids that are wetted by water in the pulp remain separated in the pulp. This method is probably the more widely used separation technique in the processing of ores. It is extensively used in the copper, zinc, nickel, cobalt, and molybdenum sections of the mineral treatment industry and is used to a lesser extent in gold and iron production. The various rubber compounds used in the lining of flotation cells and in the manufacture of their components for corrosive and abrasive duties are:

Operating above the maximum capacity can cause the performance of flotation cells to be poor even when adequate slurry residence time is available (Lynch et al., 1981). For example, Fig. 11.21 shows the impact of increasing volumetric feed flow rate on cell performance (Luttrell et al., 1999). The test data obtained at 2% solids correlates well with the theoretical performance curve predicted using a mixed reactor model (Levenspiel, 1972). Under this loading, coal recovery steadily decreased as feed rate increased due to a reduction in residence time. However, as the solids content was increased to 10% solids, the recovery dropped sharply and deviated substantially from the theoretical curve due to froth overloading. This problem can be particularly severe in coal flotation due to the high concentration of fast floating solids in the flotation feed and the presence of large particles in the flotation froth. Flotation columns are particularly sensitive to froth loading due to the small specific surface area (ratio of cross-sectional area to volume) for these units.

Theoretical studies indicate that loading capacity (i.e., carrying capacity) of the froth, which is normally reported in terms of the rate of dry solids floated per unit cross-sectional area, is strongly dependent on the size of particles in the froth (Sastri, 1996). Studies and extensive test work conducted by Eriez personnel also support this finding. As seen in Fig. 11.22, a direct correlation exists between capacity and both the mean size (d50) and ultrafines content of the flotation feedstock. The true loading capacity may be estimated from laboratory and pilot-scale flotation tests by conducting experiments as a function of feed solids content (Finch and Dobby, 1990). Field surveys indicate that conventional flotation machines can be operated with loading capacities of up to 1.52.0t/h/m2 for finer (0.150mm) feeds and 56t/h/m2 or more for coarser (0.600mm) feeds. Most of the full-scale columns in the coal industry operate at froth loading capacities less than 1.5t/h/m2 for material finer than 0.150mm and as high as 3.0t/h/m2 for flotation feed having a top size of 0.300mm feeds.

Froth handling is a major problem in coal flotation. Concentrates containing large amounts of ultrafine (<0.045mm) coal generally become excessively stable, creating serious problems related to backup in launders and downstream handling. Bethell and Luttrell (2005) demonstrated that coarser deslime froths readily collapsed, but finer froths had the tendency to remain stable for an indefinite period of time. Attempts made to overcome this problem by selecting weaker frothers or reducing frother dosage have not been successful and have generally led to lower circuit recoveries. Therefore, several circuit modifications have been adopted by the coal industry to deal with the froth stability problem. For example, froth launders need to be considerably oversized with steep slopes to reduce backup. Adequate vertical head must also be provided between the launder and downstream dewatering operations. In addition, piping and chute work must be designed such that the air can escape as the froth travels from the flotation circuit to the next unit operation.

Figure 11.23 shows how small changes in piping arrangements can result in better process performance. Shown in Fig. 11.23 is a column whose performance suffered due to the inability to move the froth product from the column launder although a large discharge nozzle (11m) had been provided. In this example, the froth built up in the launder and overflowed when the operators increased air rates. To prevent this problem, the air rates were lowered, which resulted in less than optimum coal recovery. It was determined that the downstream discharge piping was air-locking and preventing the launders from properly draining. The piping was replaced with larger chute work that allowed the froth to flow freely and the air to escape. As a result, higher aeration rates were possible and recoveries were significantly improved.

Some installations have resorted to using defoaming agents or high-pressure launder sprays to deal with froth stability. However, newer column installations eliminate this problem by including large de-aeration tanks to allow time for the froth to collapse (Fig. 11.24a). Special provisions may also be required to ensure that downstream dewatering units can accept the large froth volumes. For example, standard screen-bowl centrifuges equipped with 100mm inlets may need to be retrofitted with 200mm or larger inlets to minimize flow restrictions. In addition, while the use of screen-bowl centrifuges provides low product moistures, there are typically fine coal losses, as a large portion of the float product finer than 0.045mm is lost as main effluent. This material is highly hydrophobic and will typically accumulate on top of the thickener as a very stable froth layer, which increases the probability that the process water quality will become contaminated (i.e., black water).

This phenomenon is more prevalent in by-zero circuits, especially when the screen-bowl screen effluent is recycled back through the flotation circuit, either directly or through convoluted plant circuitry. Reintroducing material that has already been floated to the flotation circuit can result in a circulating load of very fine and highly floatable material. As a result, the capacity of the flotation equipment can be significantly reduced, which results in losses of valuable coal. Most installations will combat this by ensuring that the screen-bowl screen effluent is routed directly back to the screen bowl so that it does not return to the flotation circuit. The accumulation of froth on the thickener, which tends to be especially problematic in by-zero circuitry, is also reduced by utilizing reverse-weirs and taller center wells, as this approach helps to limit the amount of froth that can enter into the process water supply. Froth that does form on top of the clarifier can be eliminated by employing a floating boom that is placed directly in the thickener (Fig. 11.24b) and used in conjunction with water sprays. The floating boom can be constructed out of inexpensive PVC piping, and is typically attached to the rotating rakes. The boom floats on the water interface and drags any froth around to the walkway that extends over the thickener, where it is eliminated by the sprays.

Column cells have been developed over the past 30 years as an alternative to mechanically agitated flotation cells. The major operating difference between column and mechanical cells is the lack of agitation in column cells that reduces energy and maintenance costs. Also, it has been reported that the cost of installing a column flotation circuit is approximately 2540% less than an equivalent mechanical flotation circuit (Murdock et al., 1991). Improved metallurgical performance of column cells in iron ore flotation is reported and attributed to froth washing, which reduces the loss of fine iron minerals entrained into the froth phase (Dobby, 2002).

The Brazilian iron ore industry has embraced the use of column flotation cells for reducing the silica content of iron concentrates. Several companies, including Samarco Minerao S.A., Companhia Vale do Rio Doce (CRVD), Companhia Siderrgica Nacional (CSN), and Mineraes Brasileiras (MBR), are using column cells at present (Peres et al., 2007). Samarco Minerao, the first Brazilian producer to use column cells, installed column cells as part of a plant expansion program in the early 1990s (Viana et al., 1991). Pilot plant tests showed that utilization of a column recleaner circuit led to a 4% increase in iron recovery in the direct reduction concentrate and an increase in primary mill capacity when compared to a conventional mechanical circuit.

There are also some negative reports of the use of column cells in the literature. According to Dobby (2002), there were several failures in the application of column cells in the iron ore industry primarily due to issues related to scale-up. At CVRD's Samitri concentrator, after three column flotation stages, namely, rougher, cleaner, and recleaner, a secondary circuit of mechanical cells was still required to produce the final concentrate.

Imhof et al. (2005) detailed the use of pneumatic flotation cells to treat a magnetic separation stream of a magnetite ore by reverse flotation to reduce the silica content of the concentrate to below 1.5%. From laboratory testing, they claimed that the pneumatic cells performed better than either conventional mechanical cells or column cells. The pneumatic cells have successfully been implemented at the Compaia Minera Huasco's iron ore pellet plant.

This chapter presents a novel approach to establish the relationship between collector properties and the flotation behavior of goal in various flotation cells. Coal flotation selectivity can be improved if collector selection is primarily based on information obtained from prior contact angle and zeta potential measurements. In a study described in the chapter, this approach was applied to develop specific collectors for particular coals. A good correlation was obtained between laboratory batches and large-scale conventional flotation cells. This is not the case when these results are correlated with pneumatic cell trial data. The study described in the chapter was aimed at identifying reasons for the noncorrelation. Two collectors having different chemical compositions were selected for this investigation. A considerable reduction in coal recovery occurred at lower rotor speeds when comparing results of oxidized and virgin coal. The degree to which a collector enhances flocculation in both medium- and low-shear applications and also the stronger bubble-coal particle adherence required for high-shear cells must, therefore, all be taken into consideration when formulating a collector for coal flotation.

activation mechanism of lead ion in the flotation of stibnite - sciencedirect

activation mechanism of lead ion in the flotation of stibnite - sciencedirect

The floatability of stibnite was improved by treatment with the Pb2+ ion.Pb2+ could adsorb at five different sites on the stibnite surface.Xanthate further interacted with the Pb atom at the Pb-activated surface.Xanthate preferred to adsorb onto the Pb-activated surface.

The flotation of stibnite with Pb2+ as an activator was examined with micro-flotation tests, inductively coupled plasma mass spectrometry (ICP-MS) experiments and density functional theory (DFT) calculations. It was found that at a pH of 6.5, the addition of Pb(NO3)2 notably improved the flotation efficiency of stibnite with butyl xanthate (BX). At a pH of 6.5, Pb2+ was the dominant species adsorbing at the stibnite surface. DFT calculations implied that Pb2+ could adsorb at five different sites on the stibnite surface. Furthermore, BX could adsorb onto the Pb sites at the Pb-activated surface and the Sb sites of the un-activated surface, while the adsorption of BX on the Pb-activated surface is more stable.

Partial density of states (PDOS) analysis revealed that the poor overlapping between the S 3p orbital of BX and the Sb 5s orbital accounts for the weak interaction between BX and the un-activated surface. For the Pb-activated surface, the Pb 6p orbital and the S 3p orbital of BX were efficiently overlapped with each other, resulting in a relatively stronger interaction between BX and the activated surface. The DFT simulation provides a deep insight into the role of Pb2+ during the activation flotation of stibnite.

Related News
  1. energy saving quarrying hydro flotation cell equipment
  2. efficient large salt flotation cell in india
  3. flotation cell blowers
  4. efficient gangue flotation cell for sale in osaka
  5. high quality flotation machine for mineral concentration
  6. open pit mineflotation cell mobil mining machine
  7. china flotation machine
  8. flotation cell 10
  9. high quality environmental coal flotation machine sell at a loss in paris
  10. mine flotation equipment for graphite mine in goa
  11. process stone ball mill mine crushing machinery
  12. sand washer&dryer set
  13. small bentonite flotation cell in kigali
  14. rud bucket elevator chain
  15. double impeller leaching agitation tank gravity separation h
  16. tantalite mine machinery for tantalite ore separation
  17. ball milling caco3
  18. france portable magnetite rock crusher manufacturer
  19. bizerte small coal mobile crusher manufacturer
  20. rod underhill district attorney