Hello, my partner! Let's explore the mining machine together!

[email protected]

flotation concentrate machine

flotation machines

flotation machines

As pneumatic and froth separation devices are not commonly used in industry today, no further discussion about them will be given in this module. The mechanical machine is dearly the most common type of flotation machine currently used in industry, followed by the column machine which has recently experienced a rapid growth.

A mechanical machine consists of a mechanically driven impeller that disperses air into the agitated pulp. In normal practice this machine appears as a long tank-like vessel having a number of impellers in series. Mechanical machines can have open flow of pulp between the impellers or can be of cell-to-cell design with weirs between them. Below is a typical bank of flotation cells used in industrial practice.

The procedure by which air is introduced into a mechanical machine falls into two broad categories: self-aerating, where the machine uses the depression created by the impeller to induce air, and supercharged, where air is generated from an external blower. The incoming feed to the mechanical flotation machine is usually introduced in the lower portion of the machine. At the very below is shown a typical flotation cell of each air delivery type (Agitair & Denver)

The most rapidly growing class of flotation machine is the column machine, which is, as its name implies, a vessel having a large height-to-diameter ratio (from 5 to 20) in contrast tomechanical cells. This type of machine provides a counter-current flow of air bubbles and slurry with a long contact time and plenty of wash water. As might be expected, the major advantage of such a machine is the high separation grade that can be achieved, so that column cells are often used as a final concentrate cleaning step. Special care has to be exercised in the generation of fine air bubbles and the control of the feed rate to the column cell for such cells to be effective. Column cell use is often of limited value in the recovery of relatively coarse valuable particles; because of the long lifting distances involved, the bubbles can not carry large particles all the way to the top of the cell.

Probably the most significant area of change in mechanical flotation cell design has been the dramatic increase in machine cell volume with a single impeller. The idea behind this approach is that as machine size increases (assuming no loss of recovery performance with the larger machines), both plant capital and operating cost per unit of throughput decrease. In certain industrial applications today, cells of even a thousand cubic meters in volume (a large swimming pool) are being used effectively.

The throughput capabilities of various cell designs will vary with the flotation machines residence time and pulp density The number of cells required for a given operation is determined from standard engineering, mass balance calculations. In the design of a new plant, the characterization of each cells volume and flotation efficiency is generally calculated from data gathered on a laboratory scale flotation using the same type of equipment for the same material mixture in question. This procedure is then followed by the application of semi-empirically derived scale-up factors. Research work is currently under way to improve the understanding and performance of commercial flotation cells.

Currently, flotation cell design is primarily a proprietary material of the various cell manufacturers. Flotation plants are built in multiple cell configurations (called banks), and the flow through the various banks is adjusted in order to optimize plant recovery of the valuable as well as the grade of the total recovered mass from flotation. Up above is a typical flotation bank scheme. The total layout of a given flotation plant (including all of the various banks) operating on a given feed is called a flotation circuit.

The application of the air-lift to flotation is not new, but the first attempts to make use of the principle were not successful because the degree of agitation in the machine was insufficient to enable the heavy oils then in use as collecting reagents to function effectively. The advent of chemical promoters, however, made agitation of secondary and aeration of primary importance, with the result that the application of the air-lift principle became practicable and led to the introduction of the Forrester and the Hunt matless machines. South western Engineering Corporation are the owners in most countries of the rights to license and manufacture these and other types operating on the air-lift principle, and they have developed a machine based chiefly on the Welsh and Hunt patents which may be considered as representative of the type that is now most commonly used.

The Southwestern Air-Lift Machine, as it is called, consists of a V-shaped wood or steel trough of any length but of the standard cross-section shown in Fig. 40, the area of which is 9.85 sq. ft. and the interior depth 36 in. Low- pressure air is delivered from a blower through a main supply pipe to an air-pipe or header which runs longitudinally over the top of the machine. The air enters the trough itself through a seriesof vertical down-pipes , which are screwed into sockets welded tothe underside of the header at 4-in. intervals along its length and are open at their lower ends. They are from to 1 in. in diameter for roughing machines and from to in. for cleaners, and they reach to within 6 in. of the bottom. The air-lift chamber is formed by two vertical partitions, one on each side of the line of down-pipes, both of which extend from one end of the trough to the other, forming a compartment 6 in. wide. The lower edges of the partitions are an inch or two above the ends of the down-pipes and their upper edges are about level with the froth overflow lips at each side of the machine. A few inches above the top of the air-lift chamber is a deflector cap which serves to direct the rising pulp outwards and downwards against two vertical baffles. These extend the length of the trough parallel to and outside the partitions, their loweredges being several inches below the normal pulp level. The spacebetween the baffles and the sides of the machine forms two spitzkasten- shaped zones of quiet settlement where the froth collects.

The feed enters near the bottom of one end of machine and the tailing is discharged over an adjustable weir at the other end. The air, issuing in a continuous stream from the open ends of the down-pipes, carries the pulp up the central chamber on the principle of an air-lift pump. The air is subdivided into minute bubbles and more completely mixed with the pulp as the rising mass hits the cap at the top and is deflected and cascaded on to the baffles at each side, which direct it downwards, distributing the bubbles evenly throughout the pulp in the body of the machine and giving them ample opportunity to collect a coating of mineral. Rising under their own buoyancy, the bubbles enter the spitzkasten zones, up which they travel without interference, dropping most of the gangue particles mechanically entangled between them as they ascend. They collect on the surface of the pulp at the top as a mineralized froth, which is voluminous enough to pass over the lip into the concentrate launders without the need of scrapers. The pulp, on the other hand, continues its downward passage and enters the air-lift chamber again. In this way a continuous circulation of the pulp is maintained, its course through the machine being more or less in the form of a double spiral.

The aeration is generally controlled by a single valve in the header of each machine, but for selective flotation the machine is sometimes divided by transverse partitions into sections 4 ft. long, the header over each section being provided with a separate air-valve. The depth of the froth is regulated by means of the adjustable gate of the tailing weir. If difficulty is likely to be experienced in making a clean tailing with the normal amount of aeration, it is preferable to use two machines. The second one is run as a scavenger with an excess of air as compared with normal requirements, the low-grade froth so produced being pumped back to the head of the primary or roughing machine, in which the aeration is more normal in order that a comparatively clean concentrate may be produced. It is often possible to take a concentrate off the first few feet of the rougher rich enough to be sent to the filters as a finished product, the froth from the rest of the machine being pumped back to the head. When this method of flotation is adopted, it is an advantage to have the header divided into sections, each with its own valve, so that the aeration can be varied along the length of the machine. By increasing the volume of air at the discharge end the froth can be given a slight flow towards the head of the machine, with the result that the minerals are concentrated there to the exclusion of partially floatable gangue which might otherwise enter any bubbles not fully loaded with mineral.

If the froth from the feed end of the rougher is not of high enough grade, it must be re-treated in a separate cleaning machine, the length of which usually varies from one-quarter to one-half of the total length ofthe roughing and scavenging machines according to the amount of concentrate to be handled. Should still further cleaning be necessary, it is performed in a recleaner, which is generally of the same length as the cleaner. The tailings from these operations are often, but not necessarily, returned to the head of the rougher.

It is usual to prepare the pulp for flotation by adding the reagents to the grinding circuit or in a conditioning tank ahead of the flotation section, but soluble frothers such as pine oil and quick-acting promoters such as the xanthates can be added at the head of the machine if desired, since the air-lift provides enough agitation to emulsify and distribute them throughout the pulp. It is not as a rule advisable to introduce reagents into the air-lift chamber itself ; should it be necessary to do so to obtain a satisfactory recovery of the minerals, it is best to employ separate roughing and scavenging machines and to make the extra additions at the head of the scavenger.

Southwestern Air-Lift Machines are made of standard cross-section, as already stated, and in a series of lengths ranging, for ordinary purposes, from 4 to 48 ft. There is no limit to the possible length, however, and 100-ft. machines are in actual use. The tonnage capacities under different conditions will be found in Table 26. The pressure of air needed at the machine is from 1.6 to 1.7 lb. per square inch, which under normal conditions requires a pressure of about 2 lb. per square inch at the blower. It is usual to allow 75 to 100 cu. ft. of free air per minute at this pressure per foot of rougher and 45 to 70 cu. ft. per minute per foot of cleaner and recleaner. From these figures the approximate volume of air required for a machine or machines of any given length can be calculated. The power necessary to supply the air can then be found from Table 30.

The Callow Cell consists of a shallow horizontal trough, the bottom of which is covered with a porous medium, usually termed a blanket, consisting of a few layers of canvas or of a sheet of perforated rubber. Air is introduced at low pressure under the blanket, and, in passing through it, is split up into minute bubbles, which rise through the pulp in the cell, collecting a coating of mineral in the process.

Fig. 41 shows a section of the type of cell commonly employed. Its width is usually from 24 to 36 in., and its interior depth from 18 to 22 in. measured from the overflow lip ; the length varies according to requirements and is generally a multiple of the width. On the bottom are placed, side by side, the square open-topped cast-iron blanket frames or pans . The blanket covering the top of each pan is securely held in place by flat iron strips bolted round the edges, while one or two pipe grid-bars across the top prevent it from bulging. This arrangement allows a blanket to be changed in a few minutes should it becomedamaged. The air inlet to each pan projects through the bottom of the cell and is connected by a pipe and regulating valve to a header, which is provided with a main control valve.

The pulp enters one end of the cell through a feed opening and is discharged over an adjustable weir at the other end. There is no agitation, but the continuously rising stream of air bubbles keeps the particles of ore in suspension and induces a certain amount of circulation as the pulp passes along the cell. In this way the minerals are given many chances of becoming attached to the bubbles and thus of being carried over into the concentrate launder. The froth that forms on the surfaceof the pulp, usually to a depth of 8 to 10 inches, is voluminous enough to overflow the lips on each side of the cell without the use of mechanical scrapers.

For estimating purposes the average capacity of a Callow Cell may be taken as 2.5 tons of feed per square foot of blanket area per 24 hours and the air consumption as 9 cu. ft. of free air per minute per square foot of blanket at a pressure of 4 lb. per sq. in. A greater pressure is likely to be required if the blankets become blinded .

The Callow Cell has proved satisfactory for many types of ores, but it has the disadvantage that coarse or heavy sand settles on the blankets, and can only be kept in motion by flogging the latter with short rubber-buffered poles. Moreover, if lime is employed in the circuit, the blankets become impregnated and clogged with calcium carbonate, which necessitates periodical acid treatment for its removal. The use of perforated rubber sheets in place of canvas in the Callow Cell mitigates without entirely curing these difficulties, which at one time were thought to be inherent in the use of a porous medium. They have been overcome, however, by the development of the Callow-Maclntosh Machine.

The Callow-Maclntosh, or the Macintosh Machine, consists of a shallow trough or cell at the bottom of which is a hollow revolving rotor covered with a porous medium. Fig. 42 shows its construction. The pulp enters through a feed opening at one end, and is discharged at the other in much the same way as in a Callow Cell. The rotor, made of seamless steel tubing with a cast-steel ring welded in each end, is perforated with -in. holes at 7-in. centres; it is about 8 in. shorter than the length of the cell and is usually 9 in. in diameter. Its weight is taken by two hollow shafts, each fitted with a flange, which are bolted to the ends of the rotor by means of four studs. This method of attachment enables the rotor to be changed and a new one inserted with little loss of time, usually not more than 15 minutes. The shafts project through the ends of this cell and are supported on self-aligning ball and socket bearings outside, so placed that the rotor itself is a few inches clear of the bottom of the trough. A rubber gasket, shown in Fig. 43, seals the opening at each end by simple pressure on a cone-faced disc mounted on the shaft. The joint is not completely watertight and a slight leakage takes place through it at the rate of about one quart per minute. At the discharge end this escaping pulp gravitates to the tailing launder, while at the feed end it is usually led to one of the pumps returning a middling product to the roughing circuit. The gasket is preferable to a stuffing-box, as it contains no grease and requires no gland water.

The rotor covering consists of a canvas sock or of a single sheet of perforated rubber. The latter is now far more commonly employed, since it lasts five times as long as the other, its life generally exceeding 18 months ; moreover it seldom becomes blinded withcalcium carbonate, and requires an air pressure of only 2 lb. per square inch instead of the 3-lb. pressure needed for canvas. The rubber sheets are made of pure gum about 5/64 in. thick with 225 holes per sq. in., the holes being made so as to allow the air to pass through while preventing the percolation of the pulp into therotor in the event of a temporary shut-down. Two scraper bars of angle iron, 1 by 1 in., are bolted to opposite sides of the rotor on the top of the covering. They project 2 in. beyond the ends of the rotor, and their purpose is to keep in circulation any sand that settles on the bottom of the cell, at the same timeprotecting the porous medium from undue wear by contact withsuch material. Air is introduced into the rotor through one or bothof the hollow shafts, which are connected by special inlet joints with themain supply. When both ends are employed for the admission of air,the rotor is usually divided into two sections by a central partitionto enable each half to be controlled separately. The rotor is driven ata speed of about 15 r.p.m. by an individual motor connected with theshaft at one end of the cell; either a worm drive directly coupled to themotor or a chain drive coupled to the motor through a speed reducercan be employed.

The principle on which theCallow-Maclntosh Machine worksis very similar to that of a CallowCell. The air bubbles actuallyissue from the top of the rotor,where the hydraulic pressure islowest, and spread out as theyrise, their distribution throughthe pulp being quite as even andeffective as when a flat blanket isused. The cell never needs flogging since the movementof the rotor prevents sand fromsettling on it, and the scraperbars keep in circulation theheavy particles that would otherwise settle on the bottom. Themachine can, if necessary, handle ore as coarse as 20 mesh at a W/Sratio of 1/1 without choking.

The control of a pneumatic cell is different from that of a machine of the mechanically agitated type, of which each cell is capable of performing the function of a high-speed conditioner. Little conditioning takes place once the pulp has entered a pneumatic cell, and provision must therefore be made for its proper preparation when employing heavy oils or chemical reagents which need a long contact period. The froth is usually maintained at a depth of 8 to 10 in., giving an effective pulp depth of 18 to 20 in. The very large volume of air bubbles released enables flotation to be effected more rapidly than in any other type of machine, the actual time required depending mostly on the degree to which the minerals have been rendered floatable. The upward stream of bubbles is so voluminous that, under ordinary conditions, the froth overflows the lips on both sides of the cell without the need of scrapers. For the same reason a considerable quantity of gangue is often carried over into the concentrate launder by mechanical entanglement with the bubbles, and one, sometimes two, subsequent cleaning operations are generally necessary in consequence. This, however, is by no means therule ; a concentrate of high enough grade to be sent to the filtering section as a finished product can sometimes be made in a single rougher- cleaner cell. When the Callow-Macintosh Machine is run in this way (counter-current operation) a partitioned rotor is employed, since, by increasing the volume of air at the tailing-discharge end, the froth can be made to flow towards the head of the cell with the result that the minerals are concentrated there to the exclusion of gangue particles. The same effect can be obtained in a Callow Cell by regulating the admission of air to the individual pans in a similar way. If is often the practice, especially in counter-current operation, for the rougher to be followed by a scavenging cell, which is run with an excess of air as compared with the former, the froth being returned to the head of the first cell.

Callow-Macintosh Machines are made in lengths of 10, 15, and 20 ft. and in widths of 24, 30, and 36 in. with a rotor 9 in. in diameter. The vertical distance from the centre-line of the rotor to the overflow lip is about 24 in. The design of the machine, however, lends itself to the construction of larger sizes for big scale operationsi.e., up to a 30-ft. cell 48 in. wide with one or two 9-in. rotors. The 30- and 36-in. cells are sometimes fitted with rotors up to 15 in. in diameter to meet special requirements.

The capacity of the standard machine varies considerably according to the grade and character of the ore. The average capacity of a rougher or rougher-cleaner cell is from 8 to 12 tons of dry feed per foot of rotor length per 24 hours. When cleaning is practised, the tonnage per foot of total rotor length (roughers, scavengers, and cleaners) may vary from 4 tons for a slow-floating ore needing double cleaning to 10 tons for an easily-floated ore with single cleaning, the average being about 6 tons per foot of total rotor length. The cleaning section usually amounts to between one-quarter and one-half of the combined length of the roughing and scavenging cells. The width of cell employed depends on the character of the ore, the time of treatment, and the tonnage.

The quantity of air necessary varies from 5 to 7 cu. ft. per minute per square foot of aerating surface at 2- to 2-lb. pressurethat is, from 12 to 16.5 cu. ft. per minute per linear foot of rotor. With a Roots type blower the power consumption in respect of the air supply is about 12 h.p. per 1,000 cu. ft. of free air per minute at a pressure of 2 lb. per square inch. The power needed to turn the rotor averages 0.5 h.p.

gold flotation concentrate

gold flotation concentrate

The flotation method is a widely used technique for the recovery of gold from gold-containing copper ores, base metal ores, copper-nickel ores, platinum group ores and many other ores where other processes are not applicable. Flotation is also used for the removal of interfering impurities before hydrometallurgical treatment, for upgrading of low sulfide and refractory ores for further treatment. Flotation is considered to be the most cost-effective method for concentrating gold.

In this process of rock minerals that have been taken from the mine site and then destroyed by the machine to obtain a fine grain of sand to free metal-containing granules for further processing. In the destruction of mineral rocks of machine tools can use a stone crusher machine, so the minimum size of rock minerals can reach between 28 mesh.

At this stage after a mineral ore that is refined inserted into the machine agitator tank which is usually also called a flotation cell to produce a pulp slurry concentrate.Distilled water provision inserted into the flotation cell flotation machine is then run, examined the amount of initial pH and initial temperature. In the flotation tank, stirring with impellers, which are intended to produce turbulent motion of fluids (pulp), so that when inserted air flow will form air bubbles.In the pulp is then coupled collector-1,-2 collector and frother; flotation machine run back to the time varying adjustment, and examined the amount of the final pH and final temperature.

In the processflotation reagent which in use is a form of lime, bubble and collectors. Froth forming a bubble that is stable and that float to the surface as a froth flotation cell. Collector reagents react with the surface of the precious metal sulfide mineral particles making the surface is water repellent. surface of the mineral-bound water molecule is released and will be changed to hydrophobic.

Thus the collector end of the hydrophobic molecules will be bound hydrophobic molecules from the bubble, so the mineral ore can be adrift. Collector has a molecular structure similar to the detergent hydrophobic sulfide mineral grains are attached to the air bubbles that rise from the slurry zone into the froth that floats on the surface of cells.

In the flotation process of air bubbles formed initially has small size and some are attached to the surface of mineral particles. Furthermore, another air bubble formed next to join the existing air bubbles and form air bubbles with a larger size, so as to have sufficient lift to lift mineral particles to the surface. The mechanism of attachment of mineral particles in the air bubbles inside the tank during the flotation process flotation occurs when the hydrodynamic forces and the forces of interaction between mineral particles with air bubbles, resulting in collisions with air bubbles and mineral particles occurs attachment of mineral particles with air bubbles.

From the results ofbubblefrothflotation processthat resembles acolored foam detergent concentrate metallic orescarryinggold-coppermineral-ladenis thenuptothe tubshelter, and foam concentrate that has been lifted from the drain into the upper lip and into the trough flotation machine is in use as a valuable mineral collection.

In order fortheflotationprocesscan take placebyeithermeansof attachmentof particlestoairbubbleslasteduntilthetop edge of theflotationcell,it is necessary toconsiderthe followingmatters :

flotation cells

flotation cells

More ores are treated using froth flotation cells than by any other single machines or process. Non-metallics as well as metallics now being commercially recovered include gold, silver, copper, lead, zinc, iron, manganese, nickel, cobalt, molybdenum, graphite, phosphate, fluorspar, barite, feldspar and coal. Recent flotation research indicates that any two substances physically different, but associated, can be separated by flotation under proper conditions and with the correct machine and reagents. The DRflotation machine competes with Wemco and Outotec (post-outokumpu) flotation cells but are all similar is design. How do flotation cells and machinework for themineral processing industry will be better understood after you read on.

While many types of agitators and aerators will make a flotation froth and cause some separation, it is necessary to have flotation cells with the correct fundamental principles to attain high recoveries and produce a high grade concentrate. The Sub-A (Fahrenwald) Flotation Machines have continuously demonstrated their superiority through successful performance. The reliability and adaptations to all types of flotation problems account for the thousands of Sub-A Cells in plants treating many different materials in all parts of the world.

The design of Denver Sub-A flotation cells incorporates all of the basic principles and requirements of the art, in addition to those of the ideal flotation cell. Its design and construction are proved by universal acceptance and its supremacy is acknowledged by world-wide recognition and use.

1) Mixing and Aeration Zone:The pulp flows into the cell by gravity through the feed pipe, dropping directly on top of the rotating impeller below the stationary hood. As the pulp cascades over the impeller blades it is thrown outward and upward by the centrifugal force of the impeller. The space between the rotating blades of the impeller and the stationary hood permits part of the pulp to cascade over the impeller blades. This creates a positive suction through the ejector principle, drawing large and controlled quantities of air down the standpipe into the heart of the cell. This action thoroughly mixes the pulp and air, producing a live pulp thoroughly aerated with very small air bubbles. These exceedingly small, intimately diffused air bubbles support the largest number of mineral particles.

This thorough mixing of air, pulp and reagents accounts for the high metallurgical efficiency of the Sub-A (Fahrenwald) Flotation Machine, and its correct design, with precision manufacture, brings low horsepower and high capacity. Blowers are not needed, for sufficient air is introduced and controlled by the rotating impeller of the Denver Sub-A. In locating impeller below the stationary hood at the bottom of the cell, agitating and mixing is confined to this zone.

2) Separation Zone:In the central or separation zone the action is quite and cross currents are eliminated, thus preventing the dropping or knocking of the mineral load from the supporting air bubble, which is very important. In this zone, the mineral-laden air bubbles separate from the worthless gangue, and the middling product finds its way back into the agitation zone through the recirculation holes in the top of the stationary hood.

3) Concentrate Zone:In the concentrate or top zone, the material being enriched is partially separated by a baffle from the spitz or concentrate discharge side of the machine. The cell action at this point is very quiet and the mineral-laden concentrate moves forward and is quickly removed by the paddle shaft (note direct path of mineral). The final result is an unusually high grade concentrate, distinctive of the Sub-A Cell.

A flotation machine must not only float out the mineral value in a mixture of ground ore and water, but also must keep the pulp in circulation continuously from the feed end to the discharge end for the removal of the froth, and must give the maximum treatment positively to each particle.

It is an established fact that the mechanical method of circulating material is the most positive and economical, particularly where the impeller is below the pulp. A flotation machine must not only be able to circulate coarse material (encountered in every mill circuit), but also must recirculate and retreat the difficult middling products.

In the Denver Sub-A due to the distinctive gravity flow method of circulation, the rotating impeller thoroughly agitates and aerates the pulp and at the same time circulates this pulp upward in a straight line, removing the mineral froth and sending the remaining portion to the next cell in series. No short circuiting through the machine can thus occur, and this is most important, for the more treatments a particle gets, the greater the chances of its recovery. The gravity flow principle of circulation of Denver Sub-A Flotation Cell is clearly shown in the illustration below.

There are three distinctive advantages of theSub-A Fahrenwald Flotation Machines are found in no other machines. All of these advantages are needed to obtain successful flotation results, and these are:

Coarse Material Handled:Positive circulation from cell to cell is assured by the distinctive gravity flow principle of the Denver Sub-A. No short circuiting can occur. Even though the ore is ground fine to free the minerals, coarse materials occasionally gets into the circuit, and if the flotation machine does not have a positive gravity flow, choke-ups will occur.

In instances where successful metallurgy demands the handling of a dense pulp containing an unusually large amount of coarse material, a sand relief opening aids in the operation by removing from the lower part of the cell the coarser functions, directing these into the feed pipe and through the impeller of the flowing cell. The finer fraction pass over the weir overflow and thus receive a greater treatment time. In this manner short-circuiting is eliminated as the material which is bled through the sand relief opening again receives the positive action of the impeller and is subjected to the intense aeration and optimum flotation condition of each successive cell, floating out both fine and coarse mineral.

No Choke-Ups or Lost Time:A Sub-A flotation cell will not choke-up, even when material as coarse as is circulated, due to the feed and pulp always being on top of the impeller. After the shutdown it is not necessary to drain the machine. The stationary hood and the air standpipe during a shutdown protects the impeller from sanding-up and this keeps the feed and air pipes always open. Denver Sub-A flotation operators value its 24-hour per day service and its freedom from shutdowns.

This gravity flow principle of circulation has made possible the widespread phenomenal success of a flotation cell between the ball mill and classifier. The recovery of the mineral as coarse and as soon as possible in a high grade concentrate is now highly proclaimed and considered essential by all flotation operators.

Middlings Returned Without Pumps:Middling products can be returned by gravity from any cell to any other cell. This flexibility is possible without the aid of pumps or elevators. The pulp flows through a return feed pipe into any cell and falls directly on top of the impeller, assuring positive treatment and aeration of the middling product without impairing the action of the cell. The initial feed can also enter into the front or back of any cell through the return feed pipe.

Results : It is a positive fact that the application of these three exclusive Denver Sub-A advantages has increased profits from milling plants for many years by increasing recoveries, reducing reagent costs, making a higher grade concentrate, lowering tailings, increasing filter capacities, lowering moisture of filtered concentrate and giving the smelter a better product to handle.

Changes in mineralized ore bodies and in types of minerals quickly demonstrate the need of these distinctive and flexible Denver Sub-A advantages. They enable the treatment of either a fine or a coarse feed. The flowsheet can be changed so that any cell can be used as a rougher, cleaner, or recleaner cell, making a simplified flowsheet with the best extraction of mineral values.

The world-wide use of the Denver Sub-A (Fahrenwald) Flotation Machine and the constant repeat orders are the best testimonial of Denver Sub-A acceptance. There are now over 20,000 Denver Sub-A Cells in operation throughout the world.

There is no unit so rugged, nor so well built to meet the demands of the process, as the Denver Sub-A (Fahrenwald) Flotation Machine. The ruggedness of each cell is necessary to give long life and to meet the requirements of the process. Numerous competitive tests all over the world have conclusively proved the real worth of these cells to many mining operators who demand maximum result at the lower cost.

The location of the feed pipe and the stationary hood over the rotating impeller account for the simplicity of the Denver Sub-A cell construction. These parts eliminates swirling around the shaft and top of the impeller, reduce power load, and improve metallurgical results.

TheSub-A Operates in three zones: in bottom zone, impeller thoroughly mixes and aerates the pulp, the central zone separates the mineral laden particles from the worthless gangue, and in top zone the mineral laden concentrate high in grade, is quickly removed by the paddle of a Denver Sub-A Cell.

A Positive Cell Circulation is always present in theSub-A (Fahrenwald) Flotation Machine, the gravity flour method of circulating pulp is distinctive. There is no short circulating through the machine. Every Cell must give maximum treatment, as pulp falls on top of impeller and is aerated in each cell repeatedly. Note gravity flow from cell to cell.

Choke-Ups Are Eliminated in theSub-A Cell, even when material as coarse as is handled, due to the gravity flow principle of circulation. After shutdown it is not necessary to drain the machine, as the stationary hood protects impeller from sanding up. See illustration at left showing cell when shut down.

No Bowlers, noair under pressure is required as sufficient air is drawn down the standpipe. The expense and complication of blowers, air pipes and valves are thus eliminated. The standpipe is a vertical air to the heart of the Cell, the impeller. Blower air can be added if desired.

The Sub-A Flexibility allows it tobe used as a rougher, cleaner or recleaner. Rougher or middling product can be returned to the front or back of any cell by gravity without the use of pumps or elevators. Cells can be easily added when required. This flexibility is most important in operating flotation MILLS.

Pulp Level Is Controlled in each Sub-A Flotation Cell as it has an individual machine with its own pulp level control. Correct flotation requires this positive pulp level control to give best results in these Cells weir blocks are used, but handwheel controls can be furnished at a slight increase in cost. Note the weir control in each cell.

High Grade Concentrate caused by thequick removal of the mineral forth in the form of a concentrate increases the recovery. By having an adjustment paddle for each Sub-A Cell, quick removal of concentrate is assured, Note unit bearing housing for the impeller Shaft and Speed reducer drive which operates the paddle for each cell

Has Fewer Wearing Parts because Sub-A Cells are built for long, hard service, and parts subject to wear are easily replaced at low cost. Molded rubber wearing plates and impellers are light in weight give extra long life, and lower horsepower. These parts are made under exact Specifications and patented by Denver Equipment Co.

TheRugged Construction of theSub-A tank is made of heavy steel, and joints are welded both inside and out. The shaft assemblies are bolted to a heavy steel beam which is securely connected to the tank. Partition plates can be changed in the field for right or left hand machine. Right hand machine is standard.

The Minerals Separation or M.S. Sub-aeration cells, a section of which is shown in Fig. 32, consists essentially of a series of square cells with an impeller rotating on a vertical shaft in the bottom of each. In some machines the impeller is cruciform with the blades inclined at 45, the top being covered with a flat circular plate which is an integral part of the casting, but frequently an enclosed pump impeller is used with curved blades set at an angle of 45 and with a central intake on the underside ; both patterns are rotated so as to throw the pulp upwards. Two baffles are placed diagonally in each cell above the impeller to break up the swirl of the pulp and to confine the agitation to the lower zone. Sometimes the baffles are covered with a grid consisting of two or three layers each composed of narrow wood or iron strips spaced about an inch apart. The sides and bottom of the cells in the lower or agitation zone are protected from wear by liners, which are usually made of hard wood, but which can, if desired, consist of plates of cast-iron or hard rubber. The section directly under the impeller is covered with a circular cast-iron plate with a hole in the middle for the admission of pulp and air. The hole communicates with a horizontal transfer passage under the bottom liner, through which the pulp reaches the cell. Air is introduced into each cell through a pipe passing through the bottom and delivering its supply directly under the impeller. A low-pressure blower is provided with all machines except the smallest, of which the impeller speed is fast enough to draw in sufficient air by suction for normal requirements.

The pulp is fed to the first cell through a feed opening communicating with the transfer passage, along which it passes, until, at the far end, it is drawn up through the hole in the bottom liner by the suction of the impeller and is thrown outwards by its rotation into the lower zone. The square shape of the cell in conjunction with the baffles converts the swirl into a movement of intense agitation, which breaks up the air entering at the same time into a cloud of small bubbles, disseminating them through the pulp. The amount of aeration can be accurately regulated to suit the requirements of each cell by adjustment of the valve on its air pipe.

Contact between the bubbles and the mineral particles probably takes place chiefly in the lower zone. The pumping action of the impeller forces the aerated pulp continuously past the baffles into the upper and quieter part of the cell. Here the bubbles, loaded with mineral, rise more or less undisturbed, dropping out gangue particles mechanically entangled between them and catching on the way up a certain amount of mineral that has previously escaped contact. The recovery of the mineral in this way can be increased at the expense of the elimination of the gangue by increasing the amount of aeration. The froth collects at the top of the cell and is scraped by a revolving paddle over the lipat the side into the concentrate launder. The pulp, containing the gangue and any mineral particles not yet attached to bubbles, circulates to some extent through the zone of agitation, but eventually passes out through a slot situated at the back of the cell above the baffles and flows thence over the discharge weir. The height of the latter is regulated by strips of wood or iron and governs the level of the pulp in the cell. The discharge of each weir falls by gravity into the transfer passage under the next cell and is drawn up as before by the impeller. The pulp passes in this way through the whole machine until it is finally discharged as a tailing, the froth from each cell being drawn off into the appropriate concentrate launder.

No pipes are normally fitted for the transference of froth or other middling product back to the head of the machine or to any intermediate point. Should this be necessary, however, the material can be taken by gravity to the required cell through a pipe, which is bent at its lower end to pass under the bottom liner and project into the transfer passage, thus delivering its product into the stream of pulp that is being drawn up by the impeller

Particulars of the various sizes of M.S. Machines are given in Table 21. It should be noted that the size of a machine is usually defined by the diameter of its impeller ; for instance, the largest one would be described as a 24-inch machine.

The Sub-A Machine, invented by A. W. Fahrenwald and developed in many respects as an improvement in the Minerals Separation Machine, from which it differs considerably in detail, particularly in the method of aerating the pulp, although the principle of its action is essentially the same. Its construction can be seen from Figs. 33 and 34.

In common with the M.S. type of machine, it consists of a series of square cells fitted with rotating impellers. Each cell, however, is of unit construction, a complete machine being built up by mounting the required number of units on a common foundation and connecting up the pipes which transfer the pulp from one cell to the next. The cells are constructed of welded steel. The impeller, which can be rubber-lined,if required, carries six blades set upright on a circular dished disc, and is securely fixed to the lower end of the vertical driving shaft. It is covered with a stationary hood, to which are attached a stand-pipe, a feed pipe, and the middling return pipes. The underside of the hood is fitted with a renewable liner of rubber or cast-iron. The pulp, entering the first cell through the feed pipe and sometimes through the middling pipes, falls on to the impeller, the rotation of which throws it outwards into the bottom zone of agitation. The suction effect due to the rotationof the impeller draws enough air down the standpipe to supply the aeration necessary for normal operation. A portion of the pulp, cascading over the open tops of the impeller blades, entraps and breaks up the entrained air, the resulting spray-like mixture being then thrown out into the lower zone of agitation, where it is disseminated through the pulp as a cloud of fine bubbles. Should this amount of aeration be insufficient, air can be blown in under slight pressure through a hole near the top of the stand-pipe, in which case a rubber bonnet is fastenedto the lower bearing and clamped round the top of the stand-pipe so as to seal the supply from the atmosphere.

The bottom part of the cell is protected from wear by renewable cast-iron or rubber liners. Four vertical baffles, placed diagonally on the top of the hood, break up the swirl of the pulp and intensify theagitation in the lower zone. The pumping action of the impeller combined with the rising current of air bubbles carries the pulp to the quieter upper zone, where the bubbles, already coated with mineral, travel upwards, drop out many of the gangue particles which may have become entangled with them, and finally collect on the surface of the pulp as a mineralizedfroth. One side of the cell is sloped outwards so as to form, in conjunction with a vertical baffle, a spitzkasten-shaped zone of quiet settlement, where any remaining particles of gangue that have been caught and held between the bubbles are shaken out of the froth as it flows to the overflow lip at the front of the cell. The baffle prevents rising bubbles from entering the outer zone, thus enabling the gangue material released from the froth to drop down unhindered into the lower zone. A revolving paddle scrapes the froth past the overflow lip into the concentrate launder.

Should the machine be required to handle more than the normal volume of froth, it is built with a spitzkasten zone on both sides of the cell. For the flotation of ores containing very little mineral the spitzkasten is omitted so as to crowd the froth into the smallest possible space, the front of the cell being made vertical for the purpose.

Circulation of the pulp through the lower zone of agitation is maintained by means of extra holes at the base of the stand-pipe on a level with the middling return pipes. An adjustable weir provides for the discharge of the pulp to the next cell, which it enters through a feed-pipe as before. Below the weir on a level with the hood is a small sand holeand pipe through which coarse material can pass direct to the next cell without having to be forced up over the weir. The same process is repeated in each cell of the series, the froth being scraped over the lip of the machine, while the pulp passes from cell to cell until it is finally discharged as a tailing from the last one. The middling pipes make it an easy matter for froth from any section of the machine to be returned if necessary to any cell without the use of pumps.

Table 22 gives particulars of the sizes and power requirements of Denver Sub-A Machines and Table 23 is an approximate guide to their capacities under different conditions. The number of cells needed

Onemethod of driving the vertical impeller shafts of M.S. Subaeration or Denver Sub-A Machines is by quarter-twist belts from a horizontal lineshaft at the back of the machine, the lineshaft being driven in turn by a belt from a motor on the ground. This method is not very satisfactory according to modern standards, firstly, because the belts are liable to stretch and slip off, and, secondly, because adequate protection againstaccidents due to the belts breaking is difficult to provide without making the belts themselves inaccessible. A more satisfactory drive, with which most M.S. Machines are equipped, consists of a lineshaft over the top of the cells from which each impeller is driven through bevel gears. The lineshaft can be driven by a belt from a motor on the ground, by Tex- ropes from one mounted on the frame work of the machine, or by direct coupling to a slow-speed motor. This overhead gear drive needs careful adjustment and maintenance. Although it may run satisfactorily for years, trouble has been experienced at times, generally in plants where skilled mechanics have not been available. The demand for something more easily adjusted led to the development of a special form of Tex-rope drive which is shown in Fig. 35. Every impeller shaft is fitted at the top with a grooved pulley, which is driven by Tex-ropes from a vertical motor. This method is standard on Denver Sub-A Machines, and M.S. Machines are frequently equipped with it as well, but the former type are not made with the overhead gear drive except to special order.

The great advantage of mechanically agitated machines is that every cell can be regulated separately, and that reagents can be added when necessary at any one of them. Since, as a general rule, the most highly flocculated mineral will become attached to a bubble in preference to a less floatable particle, in normal operation the aeration in the first few cells of a machine should not be excessive ; theoretically there should be no more bubbles in the pulp than are needed to bring up the valuable minerals. By careful control of aeration it should be possible for the bulk of the minerals to be taken off the first few cells at the feed end of the machine in a concentrate rich enough to be easily cleaned, and sometimes of high enough grade to be sent straight to the filtering section as a finished product. The level of the pulp in these cells is usually kept comparatively low in order to provide a layer of froth deep enough to give entangled particles of gangue every chance of dropping out, but it must not be so low that the paddles are prevented from skimming off the whole of the top layer of rich mineral. Towards the end of the machine a scavenging action is necessary to make certain that the least possible amount of valuable mineral escapes in the tailing, for which purpose the gates of the discharge weirs are raised higher than at the feed end, and the amountof aeration may have to be increased. The froth from the scavenging cells is usually returned to the head of the machine, the middling pipes of the Denver Sub-A Machine being specially designed for such a purpose. The regulation of the cleaning cells is much the same as that of the first few cells of the primary or roughing machine, to the head of which the tailing from the last of the cleaning cells is usually returned.

A blower is sometimes required with the M.S. Subaeration Machine. Since each cell is fitted with an air pipe and valve, accurate regulation of aeration is a simple matter. The Denver Sub-A, Kraut, and Fagergren Machines, however, are run without blowers, enough air being drawn into the machines by suction.

In the Geco New-Cell Flotation Cellthe pneumatic principle is utilized in conjunction with an agitating device. The machine, which is illustrated in Fig. 44, consists of a trough or cell made of steel or wood, whichever is more convenient, through the bottom of which projects a series of air pipes fitted with circular mats of perforated rubber. The method of securing the mat to the air pipe can be seen from Fig. 45. Over each mat rotates a moulded rubber disc of slightlylarger diameter at a peripheral speed of 2,500 ft. per minute. It is mounted on a driving spindle as shown in Fig. 46. Each spindle is supported and aligned by ball-bearings contained in a single dust- and dirt-proof casting, and each pair is driven from a vertical motor through Tex-ropes and grooved pulleys, a rigid steel structure supporting the whole series of spindles with their driving mechanism. The machine can be supplied, if required, however, with a quarter-twist drive from a lineshaft over flat pulleys.

The air inlet pipes are connected to a main through a valve by which the amount of air admitted to each mat can be accurately controlled. The air is supplied by a low-pressure blower working at about 2 lb. per square inch. It enters the cell through the perforations in the rubber mat and is split up into a stream of minute bubbles, which are distributed evenly throughout the pulp by the action of the revolving disc. By this means a large volume of finely-dispersed air is introduced withoutexcessive agitation. There is sufficient agitation, however, to produce a proper circulation in the cell, but not enough to cause any tendency to surge or to disturb the froth on the surface of the pulp. All swirling movement is checked by the liner-baffles with which the sides of the cell are lined ; their construction can be seen in Fig. 44. They are constructed of white cast iron and are designed to last the life of the machine, the absence of violent agitation making this possible.The pulp must be properly conditioned before entering the machine. It is admitted through a feed box at one end at a point above the first disc, and passes along the length of the cell to the discharge weir without being made to pass over intermediate weirs between the discs. The height of the weir at the discharge end thus controls the level of the pulp in the machine. The froth that forms on the surface overflows the froth lip in a continuous stream without the aid of scrapers, its depth being controlled at any point by means of adjustable lip strips combined with regulation of the air.The Geco New-Cell is made in four sizesviz., 18-, 24-, 36-, and 48-in. machines, the figure representing the length of the side of the squarecell. Particulars of the three smallest sizes are given in Table 27. Figures are not available for the largest size.

integrated prediction model of bauxite concentrate grade based on distributed machine vision - sciencedirect

integrated prediction model of bauxite concentrate grade based on distributed machine vision - sciencedirect

The global and local trends of froth characteristics of different flotation stages are studied.A model for prediction of concentrate grade in rougher stage is built.The wavelet extreme learning machine algorithm is used for residual compensation model.The integrated prediction model based on distributed machine vision has a good generalization capability.A good prediction accuracy of concentrate grade is achieved.

Concentrate grade of bauxite flotation is an important technology indicator, which has a direct effect on aluminum quality. Considering the unity, locality and inaccuracy of existing prediction methods of concentrate grade based on machine vision, a distributed machine vision system of bauxite flotation process is built in this paper, from which an integrated prediction model of concentrate grade is presented. At first, we use experimental methods to analyse image data from different flotation stages, as well as comment on the relationship between its global trends and local trends. Then taking advantage of the multiple kernels least squares support vector machine and wavelet extreme learning machine, models for prediction of concentrate grade and its residual compensation are established respectively to predict the concentrate grade through integration. Finally, validation and industrial applications show that the integrated prediction model based on distributed machine vision has a good generalization capability, which can achieve a good prediction accuracy of concentrate grade, with a relative error of less than 6%, thus laying a foundation for optimal control based on mineral grade in flotation process.

Related News
  1. casting swing copper ore flotation cell wear
  2. flotation cell hack
  3. environmental pyrrhotite flotation cell in medan
  4. manganese ore flotation machine
  5. constant temperature earthquake flotation cell
  6. supplier mining machine flotation cell
  7. china flotation machine
  8. flotation cell 10
  9. high quality environmental coal flotation machine sell at a loss in paris
  10. mine flotation equipment for graphite mine in goa
  11. spiral classifiers for mineral separation
  12. single screw spiral classifier for gold ore separation
  13. jaw crusher lab scale price
  14. gold mining equipment in edmonton
  15. ball mill can be used to produce
  16. fez economic small gangue mineral processing production line price
  17. coconut shell grinding machine manufacturer in uttar pradesh
  18. gold ore beneficiation machinery
  19. ceramsite sand mobile crusher china
  20. ball mill tere sang 4.6 m 8.5 m 10