Hello, my partner! Let's explore the mining machine together!

[email protected]

impact crusher on cone crusher

impact crusher - an overview | sciencedirect topics

impact crusher - an overview | sciencedirect topics

The impact crusher (typically PE series) is widely used and of high production efficiency and good safety performance. The finished product is of cube shape and the tension force and crack is avoided. Compared with hammer crusher, the impact crusher is able to fully utilize the high-speed impact energy of entire rotor. However, due to the crushing board that is easy to wear, it is also limited in the hard material crushing. The impact crusher is commonly used for the crushing of limestone, coal, calcium carbide, quartz, dolomite, iron pyrites, gypsum, and chemical raw materials of medium hardness. Effect of process conditions on the production capacity of crushed materials is listed in Table8.10.

Depending on the size of the debris, it may either be ready to enter the recycling process or need to be broken down to obtain a product with workable particle sizes, in which case hydraulic breakers mounted on tracked or wheeled excavators are used. In either case, manual sorting of large pieces of steel, wood, plastics and paper may be required, to minimise the degree of contamination of the final product.

The three types of crushers most commonly used for crushing CDW materials are the jaw crusher, the impact crusher and the gyratory crusher (Figure 4.4). A jaw crusher consists of two plates, with one oscillating back and forth against the other at a fixed angle (Figure 4.4(a)) and it is the most widely used in primary crushing stages (Behera etal., 2014). The jaw crusher can withstand large and hard-to-break pieces of reinforced concrete, which would probably cause the other crushing machines to break down. Therefore, the material is initially reduced in jaw crushers before going through any other crushing operation. The particle size reduction depends on the maximum and minimum size of the gap at the plates (Hansen, 2004).

An impact crusher breaks the CDW materials by striking them with a high-speed rotating impact, which imparts a shearing force on the debris (Figure 4.4(b)). Upon reaching the rotor, the debris is caught by steel teeth or hard blades attached to the rotor. These hurl the materials against the breaker plate, smashing them into smaller particle sizes. Impact crushers provide better grain-size distribution of RA for road construction purposes, and they are less sensitive to material that cannot be crushed, such as steel reinforcement.

Generally, jaw and impact crushers exhibit a large reduction factor, defined as the ratio of the particle size of the input to that of the output material. A jaw crusher crushes only a small proportion of the original aggregate particles but an impact crusher crushes mortar and aggregate particles alike and thus generates a higher amount of fine material (OMahony, 1990).

Gyratory crushers work on the same principle as cone crushers (Figure 4.4(c)). These have a gyratory motion driven by an eccentric wheel. These machines will not accept materials with a large particle size and therefore only jaw or impact crushers should be considered as primary crushers. Gyratory and cone crushers are likely to become jammed by fragments that are too large or too heavy. It is recommended that wood and steel be removed as much as possible before dumping CDW into these crushers. Gyratory and cone crushers have advantages such as relatively low energy consumption, a reasonable amount of control over the particle size of the material and production of low amounts of fine particles (Hansen, 2004).

For better control of the aggregate particle size distribution, it is recommended that the CDW should be processed in at least two crushing stages. First, the demolition methodologies used on-site should be able to reduce individual pieces of debris to a size that the primary crusher in the recycling plant can take. This size depends on the opening feed of the primary crusher, which is normally bigger for large stationary plants than for mobile plants. Therefore, the recycling of CDW materials requires careful planning and communication between all parties involved.

A large proportion of the product from the primary crusher can result in small granules with a particle size distribution that may not satisfy the requirements laid down by the customer after having gone through the other crushing stages. Therefore, it should be possible to adjust the opening feed size of the primary crusher, implying that the secondary crusher should have a relatively large capacity. This will allow maximisation of coarse RA production (e.g., the feed size of the primary crusher should be set to reduce material to the largest size that will fit the secondary crusher).

The choice of using multiple crushing stages mainly depends on the desired quality of the final product and the ratio of the amounts of coarse and fine fractions (Yanagi etal., 1998; Nagataki and Iida, 2001; Nagataki etal., 2004; Dosho etal., 1998; Gokce etal., 2011). When recycling concrete, a greater number of crushing processes produces a more spherical material with lower adhered mortar content (Pedro etal., 2015), thus providing a superior quality of material to work with (Lotfi etal., 2017). However, the use of several crushing stages has some negative consequences as well; in addition to costing more, the final product may contain a greater proportion of finer fractions, which may not always be a suitable material.

Reduction of the broken rock material, or oversized gravel material, to an aggregate-sized product is achieved by various types of mechanical crusher. These operations may involve primary, secondary and even sometimes tertiary phases of crushing. There are many different types of crusher, such as jaw, gyratory, cone (or disc) and impact crushers (Fig. 15.9), each of which has various advantages and disadvantages according to the properties of the material being crushed and the required shape of the aggregate particles produced.

Fig. 15.9. Diagrams to illustrate the basic actions of some types of crusher: solid shading highlights the hardened wear-resistant elements. (A) Single-toggle jaw crusher, (B) disc or gyrosphere crusher, (C) gyratory crusher and (D) impact crusher.

It is common, but not invariable, for jaw or gyratory crushers to be utilised for primary crushing of large raw feed, and for cone crushers or impact breakers to be used for secondary reduction to the final aggregate sizes. The impact crushing machines can be particularly useful for producing acceptable particle shapes (Section 15.5.3) from difficult materials, which might otherwise produce unduly flaky or elongated particles, but they may be vulnerable to abrasive wear and have traditionally been used mostly for crushing limestone.

Reduction of the broken rock material, or oversized gravel material, to an aggregate-sized product is achieved by various types of mechanical crusher. These operations may involve primary, secondary and even sometimes tertiary phases of crushing. There are many different types of crusher, such as jaw, gyratory, cone (or disc) and impact crushers (Figure 16.8), each of which has various advantages and disadvantages according to the properties of the material being crushed and the required shape of the aggregate particles produced.

Fig. 16.8. Diagrams to illustrate the basic actions of some types of crusher: solid shading highlights the hardened wear-resistant elements (redrawn, adapted and modified from Ref. 39). (a) Single-toggle jaw crusher, (b) disc or gyrosphere crusher, (c) gyratory crusher, and (d) impact crusher.

It is common, but not invariable, for jaw or gyratory crushers to be utilised for primary crushing of large raw feed, and for cone crushers or impact breakers to be used for secondary reduction to the final aggregate sizes. The impact crushing machines can be particularly useful for producing acceptable particle shapes (section 16.5.3) from difficult materials, which might otherwise produce unduly flaky or elongated particles, but they may be vulnerable to abrasive wear and have traditionally been used mostly for crushing limestone.

The main sources of RA are either from construction and ready mixed concrete sites, demolition sites or from roads. The demolition sites produce a heterogeneous material, whereas ready mixed concrete or prefabricated concrete plants produce a more homogeneous material. RAs are mainly produced in fixed crushing plant around big cities where CDWs are available. However, for roads and to reduce transportation cost, mobile crushing installations are used.

The materiel for RA manufacturing does not differ from that of producing NA in quarries. However, it should be more robust to resist wear, and it handles large blocks of up to 1m. The main difference is that RAs need the elimination of contaminants such as wood, joint sealants, plastics, and steel which should be removed with blast of air for light materials and electro-magnets for steel. The materials are first separated from other undesired materials then treated by washing and air to take out contamination. The quality and grading of aggregates depend on the choice of the crusher type.

Jaw crusher: The material is crushed between a fixed jaw and a mobile jaw. The feed is subjected to repeated pressure as it passes downwards and is progressively reduced in size until it is small enough to pass out of the crushing chamber. This crusher produces less fines but the aggregates have a more elongated form.

Hammer (impact) crusher: The feed is fragmented by kinetic energy introduced by a rotating mass (the rotor) which projects the material against a fixed surface causing it to shatter causing further particle size reduction. This crusher produces more rounded shape.

The type of crusher and number of processing stages have considerable influence on the shape and size of RA. In general, for the same size, RAs tend to be coarser, more porous and rougher than NAs, due to the adhered mortar content (Dhir etal., 1999). After the primary crushing, which is normally performed using jaw crushers (Fong etal., 2004), it is preferable to adopt a secondary crushing stage (with cone crushers or impact crushers) (CCANZ, 2011) to further reduce the size of the CDW, producing more regularly shaped particles (Barbudo etal., 2012; Ferreira etal., 2011; Fonseca etal., 2011; Pedro etal., 2014, 2015; Gonzlez-Fonteboa and Martnez-Abella, 2008; Maultzsch and Mellmann, 1998; Dhir and Paine, 2007; Chidiroglou etal., 2008).

CDW that is subjected to a jaw crushing stage tends to result only in flatter RA (Ferreira etal., 2011; Fonseca etal., 2011; Hendriks, 1998; Tsoumani etal., 2015). It is possible to produce good-quality coarse RA within the specified size range by adjusting the crusher aperture (Hansen, 1992). In addition, the number of processing stages needs to be well thought out to ensure that the yield of coarse RA is not affected and that the quantity of fine RA is kept to the minimum (Angulo etal., 2004). This is because the finer fraction typically exhibits lower quality, as it accumulates a higher amount of pulverised old mortar (Etxeberria etal., 2007b; Meller and Winkler, 1998). Fine RA resulting from impact crushers tends to exhibit greater angularity and higher fineness modulus compared with standard natural sands (Lamond etal., 2002; Hansen, 1992; Buyle-Bodin and Hadjieva-Zaharieva, 2002).

One of the commonly known issues related to the use of RCA is its ability to generate a considerable amount of fines when the material is used (Thomas etal., 2016). As the RCA particles are moved around, they impact against one another, leading to the breakage of the friable adhered mortar, which may give rise to some technical problems such as an increase in the water demand of concrete mixes when used as an NA replacement (Thomas etal., 2013a,b; Poon etal., 2007).

The coarse fraction of RMA tends to show a higher shape index owing to the shape of the original construction material (e.g., perforated ceramic bricks) (De Brito etal., 2005). This can pose a problem in future applications as RMA may not compact as efficiently as RCA or NA (Khalaf and DeVenny, 2005). Its shape index may be reduced if the material is successively broken down to a lower particle size (De Brito etal., 2005).

Impact crushers (e.g., hammer mills and impact mills) employ sharp blows applied at high speed to free-falling rocks where comminution is by impact rather than compression. The moving parts are beaters, which transfer some of their kinetic energy to the ore particles upon contact. Internal stresses created in the particles are often large enough to cause them to shatter. These forces are increased by causing the particles to impact upon an anvil or breaker plate.

There is an important difference between the states of materials crushed by pressure and by impact. There are internal stresses in material broken by pressure that can later cause cracking. Impact causes immediate fracture with no residual stresses. This stress-free condition is particularly valuable in stone used for brick-making, building, and roadmaking, in which binding agents (e.g., tar) are subsequently added. Impact crushers, therefore, have a wider use in the quarrying industry than in the metal-mining industry. They may give trouble-free crushing on ores that tend to be plastic and pack when the crushing forces are applied slowly, as is the case in jaw and gyratory crushers. These types of ore tend to be brittle when the crushing force is applied instantaneously by impact crushers (Lewis et al., 1976).

Impact crushers are also favored in the quarry industry because of the improved product shape. Cone crushers tend to produce more elongated particles because of their ability to pass through the chamber unbroken. In an impact crusher, all particles are subjected to impact and the elongated particles, having a lower strength due to their thinner cross section, would be broken (Ramos et al., 1994; Kojovic and Bearman, 1997).

Figure 6.23(a) shows the cross section of a typical hammer mill. The hammers (Figure 6.23(b)) are made from manganese steel or nodular cast iron containing chromium carbide, which is extremely abrasion resistant. The breaker plates are made of the same material.

The hammers are pivoted so as to move out of the path of oversize material (or tramp metal) entering the crushing chamber. Pivoted (swing) hammers exert less force than they would if rigidly attached, so they tend to be used on smaller impact crushers or for crushing soft material. The exit from the mill is perforated, so that material that is not broken to the required size is retained and swept up again by the rotor for further impacting. There may also be an exit chute for oversize material which is swept past the screen bars. Certain design configurations include a central discharge chute (an opening in the screen) and others exclude the screen, depending on the application.

The hammer mill is designed to give the particles velocities of the order of that of the hammers. Fracture is either due to impact with the hammers or to the subsequent impact with the casing or grid. Since the particles are given high velocities, much of the size reduction is by attrition (i.e., particle on particle breakage), and this leads to little control on product size and a much higher proportion of fines than with compressive crushers.

The hammers can weigh over 100kg and can work on feed up to 20cm. The speed of the rotor varies between 500 and 3,000rpm. Due to the high rate of wear on these machines (wear can be taken up by moving the hammers on the pins) they are limited in use to relatively non-abrasive materials. They have extensive use in limestone quarrying and in the crushing of coal. A great advantage in quarrying is the fact that they produce a relatively cubic product.

A model of the swing hammer mill has been developed for coal applications (Shi et al., 2003). The model is able to predict the product size distribution and power draw for given hammer mill configurations (breaker gap, under-screen orientation, screen aperture) and operating conditions (feed rate, feed size distribution, and breakage characteristics).

For coarser crushing, the fixed hammer impact mill is often used (Figure 6.24). In these machines the material falls tangentially onto a rotor, running at 250500rpm, receiving a glancing impulse, which sends it spinning toward the impact plates. The velocity imparted is deliberately restricted to a fraction of the velocity of the rotor to avoid high stress and probable failure of the rotor bearings.

The fractured pieces that can pass between the clearances of the rotor and breaker plate enter a second chamber created by another breaker plate, where the clearance is smaller, and then into a third smaller chamber. The grinding path is designed to reduce flakiness and to produce cubic particles. The impact plates are reversible to even out wear, and can easily be removed and replaced.

The impact mill gives better control of product size than does the hammer mill, since there is less attrition. The product shape is more easily controlled and energy is saved by the removal of particles once they have reached the size required.

Large impact crushers will reduce 1.5m top size ROM ore to 20cm, at capacities of around 1500th1, although units with capacities of 3000th1 have been manufactured. Since they depend on high velocities for crushing, wear is greater than for jaw or gyratory crushers. Hence impact crushers are not recommended for use on ores containing over 15% silica (Lewis et al., 1976). However, they are a good choice for primary crushing when high reduction ratios are required (the ratio can be as high as 40:1) and the ore is relatively non-abrasive.

Developed in New Zealand in the late 1960s, over the years it has been marketed by several companies (Tidco, Svedala, Allis Engineering, and now Metso) under various names (e.g., duopactor). The crusher is finding application in the concrete industry (Rodriguez, 1990). The mill combines impact crushing, high-intensity grinding, and multi-particle pulverizing, and as such, is best suited in the tertiary crushing or primary grinding stage, producing products in the 0.0612mm size range. It can handle feeds of up to 650th1 at a top size of over 50mm. Figure 6.22 shows a Barmac in a circuit; Figure 6.25 is a cross-section and illustration of the crushing action.

The basic comminution principle employed involves acceleration of particles within a special ore-lined rotor revolving at high speed. A portion of the feed enters the rotor, while the remainder cascades to the crushing chamber. Breakage commences when rock enters the rotor, and is thrown centrifugally, achieving exit velocities up to 90ms1. The rotor continuously discharges into a highly turbulent particle cloud contained within the crushing chamber, where reduction occurs primarily by rock-on-rock impact, attrition, and abrasion.

This crusher developed by Jaques (now Terex Mineral Processing Solutions) has several internal chamber configurations available depending on the abrasiveness of the ore. Examples include the Rock on Rock, Rock on Anvil and Shoe and Anvil configurations (Figure 6.26). These units typically operate with 5 to 6 steel impellers or hammers, with a ring of thin anvils. Rock is hit or accelerated to impact on the anvils, after which the broken fragments freefall into the discharge chute and onto a product conveyor belt. This impact size reduction process was modeled by Kojovic (1996) and Djordjevic et al. (2003) using rotor dimensions and speed, and rock breakage characteristics measured in the laboratory. The model was also extended to the Barmac crushers (Napier-Munn et al., 1996).

Figure 9.1 shows common aluminum oxide-based grains. Also called corundum, alumina ore was mined as early as 2000 BC in the Greek island of Naxos. Its structure is based on -Al2O3 and various admixtures. Traces of chromium give alumina a red hue, iron makes it black, and titanium makes it blue. Its triagonal system reduces susceptibility to cleavage. Precious grades of Al2O3 are used as gemstones, and include sapphire, ruby, topaz, amethyst, and emerald.

Charles Jacobs (1900), a principal developer, fused bauxite at 2200C (4000F) before the turn of the 20th century. The resulting dense mass was crushed into abrasive particles. Presently, alumina is obtained by smelting aluminum alloys containing Al2O3 in electric furnaces at around 1260C (2300F), a temperature at which impurities separate from the solution and aluminum oxide crystallizes out. Depending upon the particular process and chemical composition there are a variety of forms of aluminum oxide. The poor thermal conductivity of alumina (33.5W/mK) is a significant factor that affects grinding performance. Alumina is available in a large range of grades because it allows substitution of other oxides in solid solution, and defect content can be readily controlled.

For grinding, lapping, and polishing bearing balls, roller races, and optical glasses, the main abrasive employed is alumina. Its abrasive characteristics are established during the furnacing and crushing operations, so very little of what is accomplished later significantly affects the features of the grains.

Aluminum oxide is tougher than SiC. There are four types of gradations for toughness. The toughest grain is not always the longest wearing. A grain that is simply too tough for an application will become dull and will rub the workpiece, increasing the friction, creating heat and vibrations. On the other hand, a grain that is too friable will wear away rapidly, shortening the life of the abrasive tool. Friability is a term used to describe the tendency for grain fractures to occur under load. There is a range of grain toughness suitable for each application. The white friable aluminum oxide is almost always bonded by vitrification. It is the main abrasive used in tool rooms because of its versatility for a wide range of materials. In general, the larger the crystals, the more friable the grain. The slower the cooling process, the larger are the crystals. To obtain very fine crystals, the charge is cooled as quickly as possible, and the abrasive grain is fused in small pigs of up to 2ton. Coarse crystalline abrasive grains are obtained from 5 to 6ton pigs allowed to cool in the furnace shell.

The raw material, bauxite, containing 8590% alumina, 25% TiO2, up to 10% iron oxide (Fe2O3), silica, and basic oxides, is fused in an electric-arc furnace at 2600C (4700F). The bed of crushed and calcined bauxite, mixed with coke and iron to remove impurities, is poured into the bottom of the furnace where a carbon starter rod is laid down. A couple of large vertical carbon rods are then brought down to touch and a heavy current applied. The starter rod is rapidly consumed, by which time the heat melts the bauxite, which then becomes an electrolyte. Bauxite is added over several hours to build up the volume of melt. Current is controlled by adjusting the height of the electrodes, which are eventually consumed in the process.

After cooling, the alumina is broken up and passed through a series of hammer, beater, crush, roller, and/or ball mills to reduce it to the required grain size and shape, producing either blocky or thin splintered grains. After milling, the product is sieved to the appropriate sizes down to about 40 m (#400). The result is brown alumina containing typically 3% TiO2. Increased TiO2 content increases toughness while reducing hardness. Brown alumina has a Knoop hardness of 2090 and a medium friability.

Electrofused alumina is also made using low-soda Bayer process alumina that is more than 99% pure. The resulting alumina grain is one of the hardest, but also the most friable, of the alumina family providing a cool cutting action. This abrasive in a vitrified bond is, therefore, suitable for precision grinding.

White aluminum oxide is one of the most popular grades for micron-size abrasive. To produce micron sizes, alumina is ball-milled or vibro-milled after crushing and then traditionally separated into different sizes using an elutriation process. This consists of passing abrasive slurry and water through a series of vertical columns. The width of the columns is adjusted to produce a progressively slower vertical flow velocity from column to column. Heavier abrasive settles out in the faster flowing columns while lighter particles are carried over to the next. The process is effective down to about 5 m and is also used for micron sizing of SiC. Air classification has also been employed.

White 99% pure aluminum oxide, called mono-corundum, is obtained by sulfidation of bauxite, which outputs different sizes of isometric corundum grains without the need for crushing. The crystals are hard, sharp, and have better cleavage than other forms of aluminum oxides, which qualifies it for grinding hardened steels and other tough and ductile materials. Fine-grained aluminum oxide with a good self-sharpening effect is used for finishing hardened and high-speed steels, and for internal grinding.

Not surprisingly, since electrofusion technology has been available for the last one hundred years, many variations in the process exist both in terms of starting compositions and processing routes. For example:

Red-brown or gray regular alumina. Contains 9193% Al2O3 and has poor cleavage. This abrasive is used in resinoid and vitrified bonds and coated abrasives for rough grinding when the risk of rapid wheel wear is low.

Chrome addition. Semi-fine aloxite, pink with 0.5% chromium oxide (Cr2O3), and red with 15% Cr2O3, lies between common aloxite, having less than 95% Al2O3 and more than 2% TiO2, and fine aloxite, which has more than 95% Al2O3 and less than 2% TiO2. The pink grain is slightly harder than white alumina, while the addition of a small amount of TiO2 increases its toughness. The resultant product is a medium-sized grain available in elongated, or blocky but sharp, shapes. Ruby alumina has a higher chrome oxide content of 3% and is more friable than pink alumina. The grains are blocky, sharp edged, and cool cutting, making them popular for tool room and dry grinding of steels, e.g., ice skate sharpening. Vanadium oxide has also been used as an additive giving a distinctive green hue.

Zirconia addition. Aluminazirconia is obtained during the production process by adding 1040% ZrO2 to the alumina. There are at least three different aluminazirconia compositions used in grinding wheels: 75% Al2O3 and 25% ZrO2, 60% Al2O3 and 40% ZrO2, and finally, 65% Al2O3, 30% ZrO2, and 5% TiO2. The manufacture usually includes rapid solidification to produce a fine grain and tough structure. The resulting abrasives are fine grain, tough, highly ductile, and give excellent life in medium to heavy stock removal applications and grinding with high pressures, such as billet grinding in foundries.

Titania addition. Titaniaaloxite, containing 95% Al2O3 and approximately 3% Ti2O3, has better cutting ability and improved ductility than high-grade bauxite common alumina. It is recommended when large and variable mechanical loads are involved.

Single crystal white alumina. The grain growth is carefully controlled in a sulfide matrix and is separated by acid leaching without crushing. The grain shape is nodular which aids bond retention, avoiding the need for crushing and reducing mechanical defects from processing.

Post-fusion processing methods. This type of particle reduction method can greatly affect grain shape. Impact crushers such as hammer mills create a blocky shape while roll crushers cause splintering. It is possible, using electrostatic forces to separate sharp shapes from blocky grains, to provide grades of the same composition but with very different cutting actions.

The performance of the abrasive can also be altered by heat treatment, particularly for brown alumina. The grit is heated to 11001300 C (20152375 F), depending on the grit size, in order to anneal cracks and flaws created by the crushing process. This can enhance toughness by 2540%.

Finally, several coating processes exist to improve bonding of the grains in the grinding wheel. Red Fe2O3 is applied at high temperatures to increase the surface area for better bonding in resin cut-off wheels. Silane is applied for some resin bond wheel applications to repel coolant infiltration between the bond and abrasive grit, and thus protect the resin bond.

A limitation of electrofusion is that the resulting abrasive crystal structure is very large; an abrasive grain may consist of only one to three crystals. Consequently, when grain fracture occurs, the resulting particle loss may be a large proportion of the whole grain. This results in inefficient grit use. One way to avoid this is to dramatically reduce the crystal size.

The earliest grades of microcrystalline grits were produced as early as 1963 (Ueltz, 1963) by compacting a fine-grain bauxite slurry, granulating to the desired grit size, and sintering at 1500C (2735F). The grain shape and aspect ratio could be controlled by extruding the slurry.

One of the most significant developments since the invention of the Higgins furnace was the release in 1986, by the Norton Company, of seeded gel (SG) abrasive (Leitheiser and Sowman, 1982; Cottringer et al., 1986). This abrasive was a natural outcome of the wave of technology sweeping the ceramics industry at that time to develop high strength engineering ceramics using chemical precipitation methods. This class of abrasives is often termed ceramic. SG is produced by a chemical process. In a precursor of boehmite, MgO is first precipitated to create 50-m-sized aluminamagnesia spinel seed crystals. The resulting gel is dried, granulated to size, and sintered at 1200C (2200F). The resulting grains are composed of a single-phase -alumina structure with a crystalline size of about 0.2m. Defects from crushing are avoided; the resulting abrasive is unusually tough but self-sharpening because fracture now occurs at the micron level.

With all the latest technologies, it took significant time and application knowledge to understand how to apply SG. The abrasive was so tough that it had to be blended with regular fused abrasives at levels as low as 5% to avoid excessive grinding forces. Typical blends are now five SGs (50%), three SGs (30%), and one SG (10%). These blended abrasive grades can increase wheel life by up to a factor of 10 over regular fused abrasives, although manufacturing costs are higher.

In 1981, prior to the introduction of SG, the 3M Co. introduced a solgel abrasive material called Cubitron for use in coated abrasive fiber discs (Bange and Orf, 1998). This was a submicron chemically precipitated and sintered material but, unlike SG, had a multiphase composite structure that did not use seed grains to control crystalline size. The value of the material for grinding wheel applications was not recognized until after the introduction of SG. In the manufacture of Cubitron, alumina is co-precipitated with various modifiers such as magnesia, yttria, lanthana, and neodymia to control microstructural strength and surface morphology upon subsequent sintering. For example, one of the most popular materials, Cubitron 321, has a microstructure containing submicron platelet inclusions which act as reinforcements somewhat similar to a whisker-reinforced ceramic (Bange and Orf, 1998).

Direct comparison of the performance of SG and Cubitron is difficult because the grain is merely one component of the grinding wheel. SG is harder (21GPa) than Cubitron (19GPa). Experimental evidence suggests that wheels made from SG have longer life, but Cubitron is freer cutting. Cubitron is the preferred grain in some applications from a cost/performance viewpoint. Advanced grain types are prone to challenge from a well-engineered, i.e., shape selected, fused grain that is the product of a lower cost, mature technology. However, it is important to realize that the wheel cost is often insignificant compared to other grinding process costs in the total cost per part.

The SG grain shape can be controlled by extrusion. Norton has taken this concept to an extreme and in 1999 introduced TG2 (extruded SG) grain in a product called ALTOS. The TG2 grains have the appearance of rods with very long aspect ratios. The resulting packing characteristics of these shapes in a grinding wheel create a high strength, lightweight structure with porosity levels as high as 70% or even greater. The grains touch each other at only a few points, where a bond also concentrates in the same way as a spot weld. The product offers potential for higher stock removal rates and higher wheelspeeds due to the strength and density of the resulting wheel body (Klocke and Muckli, 2000).

Recycling of concrete involves several steps to generate usable RCA. Screening and sorting of demolished concrete from C&D debris is the first step of recycling process. Demolished concrete goes through different crushing processes to acquire desirable grading of recycled aggregate. Impact crusher, jaw crusher, cone crusher or sometimes manual crushing by hammer are preferred during primary and secondary crushing stage of parent concrete to produce RA. Based on the available literature step by step flowchart for recycling of aggregate is represented in Fig. 1. Some researchers have also developed methods like autogenous cleaning process [46], pre-soaking treatment in water [47], chemical treatment, thermal treatment [48], microwave heating method [49] and mechanical grinding method for removing adhered mortar to obtain high quality of RA. Depending upon the amount of attached mortar, recycled aggregate has been classified into different categories as shown in Fig. 2.

Upon arrival at the recycling plant, CDW may either enter directly into the processing operation or need to be broken down to obtain materials with workable particle sizes, in which case hydraulic breakers mounted on tracked or wheeled excavators are used. In either case, manual sorting of large pieces of steel, wood, plastics and paper may be required, to minimize the degree of contamination.

The three types of crushers most used for crushing CDW are jaw, impact, and gyratory crushers (Fig.8). A jaw crusher consists of two plates fixed at an angle (Fig.8a); one plate remains stationary while the other oscillates back and forth relative to it, crushing the material passing between them. This crusher can withstand large pieces of reinforced concrete, which would probably cause other types of crushers to break down. Therefore, the material is initially reduced in jaw crushers before going through other types. The particle size reduction depends on the maximum and minimum size of the gap at the plates. Jaw crushers were found to produce RA with the most suitable grain-size distribution for concrete production (Molin etal., 2004).

An impact crusher breaks CDW by striking them with a high speed rotating impact, which imparts a shearing force on the debris (Fig.8b). Materials fall onto the rotor and are caught by teeth or hard steel blades fastened to the rotor, which hurl them against the breaker plate, smashing them to smaller-sized particles. Impact crushers provide better grain-size distribution of RA for road construction purposes and are less sensitive to material that cannot be crushed (i.e. steel reinforcement).

Gyratory crushers, which work on the same principle as cone crushers (Fig.8c), exhibit a gyratory motion driven by an eccentric wheel and will not accept materials with large particle sizes as they are likely to become jammed. However, gyratory and cone crushers have advantages such as relatively low energy consumption, reasonable amount of control over particle size and production of low amount of fine particles.

Generally, jaw and impact crushers have a large reduction factor, defined as the relationship between the input's particle size and that of the output. A jaw crusher crushes only a small proportion of the original aggregate particles but an impact crusher crushes mortar and aggregate particles alike, and thus may generate twice the amount of fines for the same maximum size of particle (O'Mahony, 1990).

In order to produce RA with predictable grading curve, it is better to process debris in two crushing stages, at least. It may be possible to consider a tertiary crushing stage and further, which would undoubtedly produce better quality coarse RA (i.e. less adhered mortar and with a rounder shape). However, concrete produced with RA subjected to a tertiary crushing stage may show only slightly better performance than that made with RA from a secondary crushing stage (Gokce etal., 2011; Nagataki etal., 2004). Furthermore, more crushing stages would yield products with decreasing particle sizes, which contradicts the mainstream use of RA (i.e. coarser RA fractions are preferred, regardless of the application). These factors should be taken into account when producing RA as, from an economical and environmental point of view, it means that relatively good quality materials can be produced with lower energy consumption and with a higher proportion of coarse aggregates, if the number of crushing stages is prudently reduced.

cone crusher - an overview | sciencedirect topics

cone crusher - an overview | sciencedirect topics

Cone crushers were originally designed and developed by Symons around 1920 and therefore are often described as Symons cone crushers. As the mechanisms of crushing in these crushers are similar to gyratory crushers their designs are similar, but in this case the spindle is supported at the bottom of the gyrating cone instead of being suspended as in larger gyratory crushers. Figure5.3 is a schematic diagram of a cone crusher.

The breaking head gyrates inside an inverted truncated cone. These crushers are designed so that the head-to-depth ratio is larger than the standard gyratory crusher and the cone angles are much flatter and the slope of the mantle and the concaves are parallel to each other. The flatter cone angles help to retain the particles longer between the crushing surfaces and therefore produce much finer particles. To prevent damage to the crushing surfaces, the concave or shell of the crushers is held in place by strong springs or hydraulics which yield to permit uncrushable tramp material to pass through.

The secondary crushers are designated as Standard cone crushers having stepped liners and tertiary Short Head cone crushers, which have smoother crushing faces and steeper cone angles of the breaking head. The approximate distance of the annular space at the discharge end designates the size of the cone crushers. A brief summary of the design characteristics is given in Table5.4 for crusher operation in open-circuit and closed-circuit situations.

The Standard cone crushers are for normal use. The Short Head cone crushers are designed for tertiary or quaternary crushing where finer product is required. These crushers are invariably operated in closed circuit. The final product sizes are fine, medium or coarse depending on the closed set spacing, the configuration of the crushing chamber and classifier performance, which is always installed in parallel.

For finer product sizes, i.e., less than 6mm, special cone crushers known as Gyradisc crushers are available. The operation is similar to the standard cone crushers, except that the size reduction is caused more by attrition than by impact [5]. The reduction ratio is around 8:1 and as the product size is relatively small the feed size is limited to less than 50mm with a nip angle between 25 and 30. The Gyradisc crushers have head diameters from around 900 to 2100mm. These crushers are always operated under choke feed conditions. The feed size is less than 50mm and therefore the product size is usually less than 69mm.

Maintenance of the wear components in both gyratory and cone crushers is one of the major operating costs. Wear monitoring is possible using a Faro Arm (Figure 6.10), which is a portable coordinate measurement machine. Ultrasonic profiling is also used. A more advanced system using a laser scanner tool to profile the mantle and concave produces a 3D image of the crushing chamber (Erikson, 2014). Some of the benefits of the liner profiling systems include: improved prediction of mantle and concave liner replacement; identifying asymmetric and high wear areas; measurement of open and closed side settings; and quantifying wear life with competing liner alloys.

Various types of rock fracture occur at different loading rates. For example, rock destruction by a boring machine, a jaw or cone crusher, and a grinding roll machine are within the extent of low loading rates, often called quasistatic loading condition. On the contrary, rock fracture in percussive drilling and blasting happens under high loading rates, usually named dynamic loading condition. This chapter presents loading rate effects on rock strengths, rock fracture toughness, rock fragmentation, energy partitioning, and energy efficiency. Finally, some of engineering applications of loading rate effects are discussed.

In Chapter4, we have already seen the mechanism of crushing in a jaw crusher. Considering it further we can see that when a single particle, marked 1 in Figure11.5a, is nipped between the jaws of a jaw crusher the particle breaks producing fragments, marked 2 and 3 in Figure11.5b. Particles marked 2 are larger than the open set on the crusher and are retained for crushing on the next cycle. Particles of size 3, smaller than the open set of the crusher, can travel down faster and occupy or pass through the lower portion of the crusher while the jaw swings away. In the next cycle the probability of the larger particles (size 2) breaking is greater than the smaller sized particle 3. In the following cycle, therefore, particle size 2 is likely to disappear preferentially and the progeny joins the rest of thesmaller size particles indicated as 3 in Figure11.5c. In the figures, the position of the crushed particles that do not exist after comminution is shaded white (merely to indicate the positions they had occupied before comminution). Particles that have been crushed and travelled down are shown in grey. The figure clearly illustrates the mechanism of crushing and the classification that takes place within the breaking zone during the process, as also illustrated in Figure11.4. This type of breakage process occurs within a jaw crusher, gyratory crusher, roll crusher and rod mills. Equation (11.19) then is a description of the crusher model.

In practice however, instead of a single particle, the feed consists of a combination of particles present in several size fractions. The probability of breakage of some relatively larger sized particles in preference to smaller particles has already been mentioned. For completeness, the curve for the probability of breakage of different particle sizes is again shown in Figure11.6. It can be seen that for particle sizes ranging between 0 K1, the probability of breakage is zero as the particles are too small. Sizes between K1 and K2 are assumed to break according a parabolic curve. Particle sizes greater than K2 would always be broken. According to Whiten [16], this classification function Ci, representing the probability of a particle of size di entering the breakage stage of the crusher, may be expressed as

The classification function can be readily expressed as a lower triangular matrix [1,16] where the elements represent the proportion of particles in each size interval that would break. To construct a mathematical model to relate product and feed sizes where the crusher feed contains a proportion of particles which are smaller than the closed set and hence will pass through the crusher with little or no breakage, Whiten [16] advocated a crusher model as shown in Figure11.7.

The considerations in Figure11.7 are similar to the general model for size reduction illustrated in Figure11.4 except in this case the feed is initially directed to a classifier, which eliminates particle sizes less than K1. The coarse classifier product then enters the crushing zone. Thus, only the crushable larger size material enters the crusher zone. The crusher product iscombined with the main feed and the process repeated. The undersize from the classifier is the product.

While considering the above aspects of a model of crushers, it is important to remember that the size reduction process in commercial operations is continuous over long periods of time. In actual practice, therefore, the same operation is repeated over long periods, so the general expression for product size must take this factor into account. Hence, a parameter v is introduced to represent the number of cycles of operation. As all cycles are assumed identical the general model given in Equation (11.31) should, therefore, be modified as

Multiple vectors B C written in matrix form:BC=0.580000.200.60000.120.180.6100.040.090.20.571.000000.700000.4500000=0581+00+00+000.580+00.7+00+000580+00+00.45+000.580+00+00+000.21+0.60+00+000.20+0.60.7+00+000.20+0.60+00.45+000.20+0.60+00+000.121+0.180+0.610+000.120+0.180.7+0.610+000.120+0.180+0.610.45+000.120+0.180+0.610+000.041+0.090+0.20+0.5700.040+0.090.7+0.20+0.5700.040+0.090+0.20.45+0.5700.040+0.090+0.20+0.570=0.580000.20.42000.120.1260.274500.040.0630.090

Now determine (I B C) and (I C)(IBC)=10.5800000000.210.42000000.1200.12610.27450000.0400.06300.0910=0.420000.20.58000.120.1260.725500.040.0630.091and(IC)=000000.300000.5500001

Now find the values of x1, x2, x3 and x4 as(0.42x1)+(0x2)+(0x3)+(0x4)=10,thereforex1=23.8(0.2x1)+(0.58x2)+(0x3)+(0x4)=33,thereforex2=65.1(0.12x1)+(0.126x2)+(0.7255x3)+(0x4)=32,thereforex3=59.4(0.04x1)+(0.063x2)+(0.09x3)+(1x4)=20,thereforex4=30.4

In this process, mined quartz is crushed into pieces using crushing/smashing equipment. Generally, the quartz smashing plant comprises a jaw smasher, a cone crusher, an impact smasher, a vibrating feeder, a vibrating screen, and a belt conveyor. The vibrating feeder feeds materials to the jaw crusher for essential crushing. At that point, the yielding material from the jaw crusher is moved to a cone crusher for optional crushing, and afterward to effect for the third time crushing. As part of next process, the squashed quartz is moved to a vibrating screen for sieving to various sizes.

Crushers are widely used as a primary stage to produce the particulate product finer than about 50100mm. They are classified as jaw, gyratory, and cone crushers based on compression, cutter mill based on shear, and hammer crusher based on impact.

A jaw crusher consists essentially of two crushing plates, inclined to each other forming a horizontal opening by their lower borders. Material is crushed between a fixed and a movable plate by reciprocating pressure until the crushed product becomes small enough to pass through the gap between the crushing plates. Jaw crushers find a wide application for brittle materials. For example, they are used for comminution of porous copper cake. A Fritsch jaw crusher with maximal feed size 95mm, final fineness (depends on gap setting) 0.315mm, and maximal continuous throughput 250Kg/h is shown in Fig. 2.8.

A gyratory crusher includes a solid cone set on a revolving shaft and placed within a hollow body, which has conical or vertical sloping sides. Material is crushed when the crushing surfaces approach each other and the crushed products fall through the discharging opening.

Hammer crushers are used either as a one-step primary crusher or as a secondary crusher for products from a primary crusher. They are widely used for crushing hard metal scrap for different hard metal recycling processes. Pivoted hammers are pendulous, mounted on the horizontal axes symmetrically located along the perimeter of a rotor. Crushing takes place by the impact of material pieces with the high speed moving hammers and by contact with breaker plates. A cylindrical grating or screen is placed beneath the rotor. Materials are reduced to a size small enough to pass through the openings of the grating or screen. The size of the product can be regulated by changing the spacing of the grate bars or the opening of the screen.

The feature of the hammer crushers is the appearance of elevated pressure of air in the discharging unit of the crusher and underpressure in the zone around the shaft close to the inside surface of the body side walls. Thus, the hammer crushers also act as high-pressure, forced-draught fans. This may lead to environmental pollution and product losses in fine powder fractions. A design for a hammer crusher (Fig. 2.9) essentially allows a decrease of the elevated pressure of air in the crusher discharging unit [5]. The A-zone beneath the screen is communicated through the hollow ribs and openings in the body side walls with the B-zone around the shaft close to the inside surface of body side walls. As a result, the circulation of suspended matter in the gas between A and B zones is established and the high pressure of air in the discharging unit of crusher is reduced.

Crushers are widely used as a primary stage to produce the particulate product finer than about 50100 mm in size. They are classified as jaw, gyratory and cone crushers based on compression, cutter mill based on shear and hammer crusher based on impact.

A jaw crusher consists essentially of two crushing plates, inclined to each other forming a horizontal opening by their lower borders. Material is crushed between a fixed and a movable plate by reciprocating pressure until the crushed product becomes small enough to pass through the gap between the crushing plates. Jaw crushers find a wide application for brittle materials. For example, they are used for comminution of porous copper cake.

A gyratory crusher includes a solid cone set on a revolving shaft and placed within a hollow body, which has conical or vertical sloping sides. Material is crushed when the crushing surfaces approach each other and the crushed products fall through the discharging opening.

Hammer crushers are used either as a one-step primary crusher or as a secondary crusher for products from a primary crusher. They are widely used for crushing of hard metal scrap for different hard metal recycling processes.

Pivoted hammers are pendulous, mounted on the horizontal axes symmetrically located along the perimeter of a rotor and crushing takes place by the impact of material pieces with the high speed moving hammers and by contact with breaker plates. A cylindrical grating or screen is placed beneath the rotor. Materials are reduced to a size small enough pass through the openings of the grating or screen. The size of product can be regulated by changing the spacing of the grate bars or the opening of the screen.

The feature of the hammer crushers is the appearance of elevated pressure of air in the discharging unit of the crusher and underpressure in the zone around of the shaft close to the inside surface of the body side walls. Thus, the hammer crushers also act as high-pressure forced-draught fans. This may lead to environmental pollution and product losses in fine powder fractions.

A design for a hammer crusher (Figure 2.6) allows essentially a decrease of the elevated pressure of air in the crusher discharging unit [5]. The A-zone beneath the screen is communicated through the hollow ribs and openings in the body side walls with the B-zone around the shaft close to the inside surface of body side walls. As a result, circulation of suspended matter in the gas between A- and B-zones is established and high pressure of air in the discharging unit of crusher is reduced.

For a particular operation where the ore size is known, it is necessary to estimate the diameter of rolls required for a specific degree of size reduction. To estimate the roll diameter, it is convenient to assume that the particle to be crushed is spherical and roll surfaces are smooth. Figure6.2 shows a spherical particle about to enter the crushing zone of a roll crusher and is about to be nipped. For rolls that have equal radius and length, tangents drawn at the point of contact of the particle and the two rolls meet to form the nip angle (2). From simple geometry it can be seen that for a particle of size d, nipped between two rolls of radius R:

Equation (6.2) indicates that to estimate the radius R of the roll, the nip angle is required. The nip angle on its part will depend on the coefficient of friction, , between the roll surface and the particle surface. To estimate the coefficient of friction, consider a compressive force, F, exerted by the rolls on the particle just prior to crushing, operating normal to the roll surface, at the point of contact, and the frictional force between the roll and particle acting along a tangent to the roll surface at the point of contact. The frictional force is a function of the compressive force F and is given by the expression, F. If we consider the vertical components of these forces, and neglect the force due to gravity, then it can be seen that at the point of contact (Figure6.2) for the particle to be just nipped by the rolls, the equilibrium conditions apply where

As the friction coefficient is roughly between 0.20 and 0.30, the nip angle has a value of about 1117. However, when the rolls are in motion the friction characteristics between the ore particle will depend on the speed of the rolls. According to Wills [6], the speed is related to the kinetic coefficient of friction of the revolving rolls, K, by the relation

Equation (6.4) shows that the K values decrease slightly with increasing speed. For speed changes between 150 and 200rpm and ranging from 0.2 to 0.3, the value of K changes between 0.037 and 0.056. Equation (6.2) can be used to select the size of roll crushers for specific requirements. For nip angles between 11 and 17, Figure6.3 indicates the roll sizes calculated for different maximum feed sizes for a set of 12.5mm.

The maximum particle size of a limestone sample received from a cone crusher was 2.5cm. It was required to further crush it down to 0.5cm in a roll crusher with smooth rolls. The friction coefficient between steel and particles was 0.25, if the rolls were set at 6.3mm and both revolved to crush, estimate the diameter of the rolls.

It is generally observed that rolls can accept particles sizes larger than the calculated diameters and larger nip angles when the rate of entry of feed in crushing zone is comparable with the speed of rotation of the rolls.

Jaw crushers are mainly used as primary crushers to produce material that can be transported by belt conveyors to the next crushing stages. The crushing process takes place between a fixed jaw and a moving jaw. The moving jaw dies are mounted on a pitman that has a reciprocating motion. The jaw dies must be replaced regularly due to wear. Figure 8.1 shows two basic types of jaw crushers: single toggle and double toggle. In the single toggle jaw crusher, an eccentric shaft is installed on the top of the crusher. Shaft rotation causes, along with the toggle plate, a compressive action of the moving jaw. A double toggle crusher has, basically, two shafts and two toggle plates. The first shaft is a pivoting shaft on the top of the crusher, while the other is an eccentric shaft that drives both toggle plates. The moving jaw has a pure reciprocating motion toward the fixed jaw. The crushing force is doubled compared to single toggle crushers and it can crush very hard ores. The jaw crusher is reliable and robust and therefore quite popular in primary crushing plants. The capacity of jaw crushers is limited, so they are typically used for small or medium projects up to approximately 1600t/h. Vibrating screens are often placed ahead of the jaw crushers to remove undersize material, or scalp the feed, and thereby increase the capacity of the primary crushing operation.

Both cone and gyratory crushers, as shown in Figure 8.2, have an oscillating shaft. The material is crushed in a crushing cavity, between an external fixed element (bowl liner) and an internal moving element (mantle) mounted on the oscillating shaft assembly. An eccentric shaft rotated by a gear and pinion produces the oscillating movement of the main shaft. The eccentricity causes the cone head to oscillate between the open side setting (o.s.s.) and closed side setting (c.s.s.). In addition to c.s.s., eccentricity is one of the major factors that determine the capacity of gyratory and cone crushers. The fragmentation of the material results from the continuous compression that takes place between the mantle and bowl liners. An additional crushing effect occurs between the compressed particles, resulting in less wear of the liners. This is also called interparticle crushing. The gyratory crushers are equipped with a hydraulic setting adjustment system, which adjusts c.s.s. and thus affects product size distribution. Depending on cone type, the c.s.s. setting can be adjusted in two ways. The first way is by rotating the bowl against the threads so that the vertical position of the outer wear part (concave) is changed. One advantage of this adjustment type is that the liners wear more evenly. Another principle of setting adjustment is by lifting/lowering the main shaft. An advantage of this is that adjustment can be done continuously under load. To optimize operating costs and improve the product shape, as a rule of thumb, it is recommended that cones always be choke-fed, meaning that the cavity should be as full of rock material as possible. This can be easily achieved by using a stockpile or a silo to regulate the inevitable fluctuation of feed material flow. Level monitoring devices that detect the maximum and minimum levels of the material are used to start and stop the feed of material to the crusher as needed.

Primary gyratory crushers are used in the primary crushing stage. Compared to the cone type crusher, a gyratory crusher has a crushing chamber designed to accept feed material of a relatively large size in relation to the mantle diameter. The primary gyratory crusher offers high capacity thanks to its generously dimensioned circular discharge opening (which provides a much larger area than that of the jaw crusher) and the continuous operation principle (while the reciprocating motion of the jaw crusher produces a batch crushing action). The gyratory crusher has capacities starting from 1200 to above 5000t/h. To have a feed opening corresponding to that of a jaw crusher, the primary gyratory crusher must be much taller and heavier. Therefore, primary gyratories require quite a massive foundation.

The cone crusher is a modified gyratory crusher. The essential difference is that the shorter spindle of the cone crusher is not suspended, as in the gyratory, but is supported in a curved, universal bearing below the gyratory head or cone (Figure 8.2). Power is transmitted from the source to the countershaft to a V-belt or direct drive. The countershaft has a bevel pinion pressed and keyed to it and drives the gear on the eccentric assembly. The eccentric assembly has a tapered, offset bore and provides the means whereby the head and main shaft follow an eccentric path during each cycle of rotation. Cone crushers are used for intermediate and fine crushing after primary crushing. The key factor for the performance of a cone type secondary crusher is the profile of the crushing chamber or cavity. Therefore, there is normally a range of standard cavities available for each crusher, to allow selection of the appropriate cavity for the feed material in question.

The main task of renovation construction waste handling is the separation of lightweight impurities and construction waste. The rolling crusher with opposite rollers is capable of crushing the brittle debris and compressing the lightweight materials by the low-speed and high-pressure extrusion of the two opposite rollers. As the gap between the opposite rollers, rotation speed, and pressure are all adjustable, materials of different scales in renovation construction waste can be handled.

The concrete C&D waste recycling process of impact crusher+cone crusher+hoop-roller grinder is also capable of handling brick waste. In general, the secondary crushing using the cone crusher in this process with an enclosed crusher is a process of multicrushing, and the water content of waste will become an important affecting factor. The wet waste will be adhered on the wall of the grinding chamber, and the crushing efficiency and waste discharging will be affected. When the climate is humid, only coarse impact crushing is performed and in this case the crushed materials are used for roadbase materials. Otherwise, three consecutive crushings are performed and the recycled coarse aggregate, fine aggregate, and powder materials are collected, respectively.

The brick and concrete C&D waste recycling process of impact crusher+rolling crusher+hoop-roller grinder is also capable of handling the concrete waste. In this case, the water content of waste will not be an important affecting factor. This process is suitable in the regions with wet climates.

The renovation C&D waste recycling process of rolling crusher (coarse/primary crushing)+rolling crusher (intermediate/secondary crushing)+rolling crusher (fine/tertiary crushing) is also capable of handling the two kinds of waste discussed earlier. The particle size of debris is crushed less than 20mm and the lightweight materials are compressed, and they are separated using the drum sieve. The energy consumption is low in this process; however, the shape of products is not good (usually flat and with cracks). There is no problem in roadbase material and raw materials of prefabricated product production. But molders (the rotation of rotors in crusher is used to polish the edge and corner) should be used for premixed concrete and mortar production.

cone crusher vs. impact crusher | quarrying & aggregates

cone crusher vs. impact crusher | quarrying & aggregates

Not every crusher is suitable for every application. When choosing the best crusher for aggregate applications, it is important to understand how the crusher works and its impact on efficiency, operating costs and final products. When designing aggregate processing production line plans, there are usually differences in the choice of impact and cone crusher. What is the difference between impact crusher and cone crusher? Which is the best fine crushing equipment?

For impact crusher, the high-speed rotating rotor throw stone into impact plates, stones are crushed via impact energy produced rotating rotor. So, impact crusher is good to crush soft material of brittle stone.

Initial High-manganese steel is softer than high-chrome steel, but high-manganese steel has features of high tenacity, that means after many times strike and crushing stone, this high-manganese steel will become harder and harder, so, high-manganese steel is usually used to crush hard stone, and its service life will be very long. So, both jaw plates of jaw crusher and bowl liner & mantle of cone crusher are made from high-manganese steel.

High chromium iron is very hard, but it is a little brittle, so, it usually used to crush soft material like lime stone. Therefore, the most common blow bar/hammer material of impact crusher is high chromium iron.

According to our experience in Zambia and Nigeria, most of the local raw materials are hard stones like granite, so most investors or equipment owners in Zambia and Nigeria usually use cone crushers as secondary crushers. Because of its high production efficiency and low maintenance costs for hard stones.

Due to the different types, sizes and uses of stone crushers, and the large investment required to purchase stone crushers, it will make the purchase of equipment difficult. When you are looking for crushers or other aggregate equipment, please contact our aggregate equipment experts to help you make the right choice in the first time.

mobile crusher | mobile jaw & impact & cone crushers | jxsc mine

mobile crusher | mobile jaw & impact & cone crushers | jxsc mine

The mobile crusher is a new originality rock crushing equipment. It has mobility compared to other crushers machine. So it solves the problem of limiting crusher place and environment. And the equipment provides an efficient, low-cost and portable stone crusher plant. The mobile stone crusher plant is mainly used for metallurgy, chemical industry, building materials, hydropower and other materials that often need to be moved. Especially for the operation of crushed stone such as highways, railways, hydropower projects. The tyre crushing machine and tracked crusher are two types of portable crushing. According to the needs of working, JXSC products mobile jaw crusher, impact crusher, cone crusher, and screen equipment.

The mobile crushing plant has strong mobility and can be used directly on the spot. The plant reduces set-up time and construction work cost. It is widely used in mining crushing process, construction waste recycling, waste concrete recycling, the crushed stone that the roads need.

After being treated, the bulk aggregate material which reaches the particle size of the movable jaw crusher. From the excavator to the mobile vibration feeder. The aggregate is uniformly put into a mobile jaw crusher for primary crushing. The primary crushed aggregates are fed into a secondary crusher (mobile impact crusher or mobile cone crusher). Then the finished aggregates are screened by mobile vibrating screen. Finished aggregates of various sizes are transported to the product stack by belt conveyor. And the crushed aggregates larger than the finished aggregates are conveyed into the secondary crusher by belt conveyor.

Structure: Our company product complete varieties of mobile quarry crushing plant, specifications series, give you more choice. According to the different needs of customers, provide a diverse portfolio of mobile crushing equipment, to meet the customer's production needs. There is portable mobile jaw crusher plant, impact crusher plant, cone crusher plant. Mobile jaw crusher plant: vibrating feeder, jaw crusher, belt conveyor. Impact mobile crushing station: vibrating screen, impact crusher, belt conveyor. Mobile cone crushing and screening plant: vibrating screen, cone crusher, belt conveyor.

Performance characteristics: 1. Flexible configuration, stand-alone operations, but also multi equipment operation. Vehicle-mounted motor and control box integration. 2. Integrated vehicle installation, compact structure, easy to use. 3. Vehicle-mounted support, equipment site based convenience. 4. Steering traction shaft, convenient highway transportation and in-depth site.Mobile performance is strong, high applicability. 5. Cost savings, reduce costs. 6. Stable performance, easy to repair.

Tyre Type used the car body is Half hanging, it can smooth movement at the road or other rugged roads with locomotives. The wheel mobile crushing is suitable for the disposal of engineering waste and other construction waste in urban areas. The equipment has high working efficiency because its stability is good than the track crusher machine.

Track Type employed full hydraulic drive chassis. It is adaptable to climbing, mountain and wetland environments where complex crushing places. The track mobile stone crusher price is higher than the wheel. And it can remote-control with a wireless, high degree of automation. JXSC Mine Machinery Factory mobile crushers for sale, inquire now.

Jiangxi Shicheng stone crusher manufacturer is a new and high-tech factory specialized in R&D and manufacturing crushing lines, beneficial equipment,sand-making machinery and grinding plants. Read More

the models and parameters of cone crusher | hxjq

the models and parameters of cone crusher | hxjq

Processing Materials: river pebbles, granite, marble, limestone, fluorite ore, gold ore, barite, calcite, dolomite, bluestone, glass, basalt, iron ore, etc.

The cone crusher is a kind of stone crusher machine applied for metallurgy, building, road construction, chemical engineering, etc. It is suitable for medium and fine crushing with the features of high crushing ratio, high efficiency, low energy consumption and uniform particle size.

There are different models in HXJQ divided by different crushing principles and different particle sizes: single cylinder hydraulic cone crusher, multi-cylinder hydraulic cone crusher, hydraulic cone crusher, Symons cone crusher (compound cone crusher), and spring cone crusher. At present, the most advanced one is the single cylinder hydraulic cone crusher, and the most popular one is the Symons cone crusher.

The structure of single-cylinder hydraulic cone crusher is simple. Its characteristics are the steep cone, high swing frequency, and small eccentric distance. The unique design structure of bottom single cylinder can complete the three functions which can adjust the discharge opening directly, prevent ferric materials, and clear chambers.

The Symons cone crusher has the hydraulic chamber-cleaning system which can reduce its downtime. This machine adopts the lubrication grease system which avoids the defects of water-supplying and discharging block as well as mixing the water and oil easily. The spring insurance system is an overload protection device, which can make the foreign matter and iron ore go through the crushing chamber without damage.

When the single-cylinder hydraulic cone crusher is working, the motor drives the small gear of the crusher, the pinion drives the large gear, and the large gear assembly drives the eccentric sleeve assembly and the spindle assembly, which are centered on the theoretical vertical line, and rotate in the copper bushing.

The spindle assembly in the eccentric copper sleeve with the center line of the spindle can realize the rotating material being crushed by the swinging inner cone, and the crushed material is discharged from the discharge port.

When the compound cone crusher is working, the motor drives the eccentric sleeve to rotate by the V-belt, transmission shaft and bevel gears. The moving cone rotates under the action of the eccentric sleeve. The material is continuously crushed and impacted in the crushing chamber, then the needed size of the material after crushing will falls under the gravity and be discharged from the bottom. Symons cone crusher controls the particle size of material according to reducing the size of the discharge opening, so it is not suitable for ultra-fine sand or sand making.

The technology of single-cylinder hydraulic cone crusher is more advanced and higher efficient to operate. Under the condition of the constant crushing chamber, the maximum feeding size and productivity can keep constant, it has higher output, longer liner life, and lower operating costs. Its mainframe weight is 5700 to 36,300 kg, the weight of Symons cone crusher is 9980 to 43,270 kg, and its volume and weight are smaller than Symons cone crusher. Therefore, it is more convenient and quick to install and transport, as well as lift and change parts.

Jaw crusher, cone crusher and impact crusher are the mainstream crushers used in mining industries. Jaw crusher and cone crusher are the classical laminated crushers, and also the most popular crushers, while impact crusher adopts impact crushing principle. In general, jaw crusher is used as the primary crusher, and cone crusher and impact crusher as the secondary. And they always combine with each other in the whole crushing line during the crushing process.

Jaw crusher and cone crusher adopt the laminating crushing principle, known as extrusion crushing principle. Although the crushing actuators are different, the nature of crushing does not make much difference.

During the crushing process, the cone crusher adopts the extrusion between the mortar wall and the crushing wall, and the jaw crusher adopts the extrusion between the mobile jaw and the fixed jaw.

Impact crusher adopts the impact crushing principle, and materials are impacted and crushed between hammer and impact plate. Due to the frequent impact, the wearing parts are easy to damage, so impact crusher has a high requirement on the wear-resistance materials.

The jaw crusher, cone crusher and impact crusher are widely used in a variety of materials, but they have different applicability. The jaw crusher can almost meet the requirements of all materials.

Cone crusher also has the wide applications, ans it can crush high-hardness materials in high efficiency. However, impact crusher is generally used for crushing soft materials such as limestone because its crushing principle and wear-resistant parts, and impact has a good performance in shaping.

When choosing crusher machines, a comparison should be conducted according to different situations. Generally, jaw crusher is used for primary crushing, and for second crushing or fine crushing, a large ore-dressing plant always chooses the cone crusher, and a medium or small plant chooses the impact crusher.

Generally, jaw crusher is suitable for all kinds of crushing lines, and it is relatively cheaper than cone crusher because of the large market. Though impact crusher has a cheap price, it has several wear-resistant parts such as hammer and impact plate, which should be replaced after several times uses, so impact crusher has a high using cost.

Although cone crusher is relatively expensive, the wear-resistant parts have long service life to avoid the worries of changing parts frequently. Therefore, cone crusher has higher performance-price ratio than impact crusher in the long run.

HXJQ as a professional cone crusher manufacturer has produced crushers for more than 40 years, and we have the crushers with the lowest cone crusher prices and highest quality. If you have any problems in the selection of equipment, please timely consult HXJQ, there are experts who will guide for you in the whole process and choose the most suitable, cheapest, and best-performance equipment for you.

Related News
  1. impact crusher machine
  2. impact crusher manufacturer limestone 100 tph
  3. impact classifier techniques
  4. shear impact attrition forces in mill and ball
  5. how does a impact crusher work
  6. complex vertical impact crusher indonesia
  7. impact kickboxing
  8. crushing impact crusher history
  9. roll impact crusher
  10. fine impact crusher machine price
  11. raymond mills
  12. hand rock crusher
  13. jaw crusher for limestone manufacturer
  14. operation of a stone cone crusher
  15. crusher belt supplier
  16. portable mineral rock crusher in genoa
  17. cement ball mill for grinding mica
  18. cara kerja mesin hammer crusher
  19. vacuum freeze dryer lyophilisateur industriel freeze dryer machine precio liofilizador freeze dryer buy
  20. jaw crusher plant south africa in ethiopia