china plant of mineral processing manufacturer, jaw crusher, gold recovery equipment supplier - yantai huize mining engineering co., ltd
Jaw Crusher, Gold Recovery Equipment, Ball Mill manufacturer / supplier in China, offering Ore Processing Plant Mini Gold Stone Crusher, Small Size Jaw Crusher of Gold Mineral Processing Plant, Small Scale Ore Jaw Crusher of Mineral Processing Plant and so on.
Yantai Huize Mining Engineering Co., Ltd (HZE), LED by a professional team which is proficient in management and technology and has more than twenty years of experience, is dedicated to providing the global clients with various forms of services in mineral processing and ore beneficiation field. Our services include feasibility study, technology research and development, metallurgical test, engineering design, equipment manufacturing and supply, on-site installation, commissioning, staff training, operation ...
placer mining equipment
Specific placer mining equipment is needed for each of the methods which can be classified according to the several methods of excavating and transporting the gravel, or they may be designated to correspond with the various ways of saving the gold. The actual moving of the gravel from place is always the principal concern of the miner, and often the gold-saving is entirely incidental to the working of the deposit. The following classification, therefore, seems the most logical and is the one generally used by placer miners:
Hand-shoveling.- Hand-shoveling comprises picking and shoveling surface-placer gravels and washing the material excavated to recover the valuable minerals. The gravel may be washed at the diggings or transported by wheelbarrows, pack animals, carts, or trucks to the nearest available water. The general method of excavating varies little, but it may be subdivided according to the method of washing the gravel: (a) Panning; (b) rocking; (c) use of long torn; (d) shoveling into boxes (sluicing); and (e) dry washing.
Ground-sluicing.- Ground-sluicing consists of moving and washing gravel by water not under a hydraulic head. The action of the water usually is assisted by picking. Boulders may be removed by hand of by derricks. A minor part of the water under relatively low pressure may be used to assist in cutting the bank.
Hydraulicking.- This method of mining utilizes water under pressure from a nozzle for cutting the gravel and sweeping it into sluice boxes, through which it passes to a suitable dumping ground. Additional water not under pressure generally is used to assist in moving the washed material through the sluice boxes.
Excavating by teams or power equipment.- This heading includes mining by teams and scrapers, power scrapers, power shovels, and drag-line excavators but not dredges. The gold may be washed in standard sluice boxes or in more complicated power-driven screening and washing plants.
Dredging.- Dredging properly is confined to mining placer deposits by excavating and washing machinery mounted on boats. The so-called land dredges as well as floating washing plants fed by separate dry-land excavators are included under the previous method. The only type of gold dredge operating successfully in this country is the bucket type, which excavates by means of an endless chain of buckets, screens and washes the gravel, recovers the gold in sluices, and discharges the waste material into the water behind the boat.
Drift-mining.- Drift-mining consists of working buried strata of gold-bearing gravels by underground methods. The gravels are mined in much the same manner as flat lode deposits; the excavated material is taken to the surface and washed in sluice boxes or treated in other gold-saving devices. In some instances the milling practice resembles that used for extracting gold from lode ores.
The method that involves the lowest total cost is preferable for mining a given deposit. The method chosen, however, must be compatible with existing conditions; frequently only a relatively high-cost method will be practicable. Usually natural conditions restrict the selection of a method, The most important natural factors are the quantity and pressure of water available; the slope or grade of surface and bedrock; the depth, extent, and value per yard of the deposit the character of gravel and bedrock; and the thickness of the overburden.
For profitable exploitation of a mine the gold recovered must be of greater value than the cost of mining it. Although in the past extremely rich placer ground has been found and worked, present known surface placer deposits are of relatively low grade. For profitable operation, relatively large tonnages must be handled per man-shift; too much stress cannot be laid upon this item. All phases of the mining must be correlated, and delays must be reduced to a minimum. Complications in any part of the set-up are to be avoided whenever possible in order that no bottle necks may exist. The mine and plant must be so designed and laid out that operations can be maintained at full capacity throughout the season, especially where power excavators or mechanical washing plants are used. Often the difference between expected capacity and actual capacity has been considerable and has meant the difference between profit and loss.
Deciding to invest in, buying and mobilise small-scale GoldPlacer Mining EquipmentBC requires professional, experienced evaluation.The essential criteria should be examined at the outset to see if the given parameters of size and tenor fit.Second, no final decision to mobilize the placer mining equipment should be made until the property has been competently evaluated. The selection of proper equipment and seeking professional help in running the operation, must be the next priorities if the investor/mining company is to make a profit in this scale of mining business.
There has been a tendency to use lower cost equipment in small scale placer gold washing/processing plants with little regard -for its ability to recover the majority of gold. This includes using flat shaking screens for classification and riffles for concentration. Few have knowledge of amalgamation and thus will not have a continuous system for recovery.
The history of placer gold recovery systems shows a slow development of technology until the bucket ladder mining dredge was combined with a processing plant as a single system. While mineral jigs were being actively developed for other minerals in the 1880s, no application was made for placer gold on a dredge until about 1914, in California. Until that time and for some years after, only riffles were used and records have shown that as much as 4071 of the gold was lost to tailings. Adding jigs to the circuit recovered more and by the mid 1930s our company and a small dredge operator in Idaho, took the lead and replaced riffles with jigs on our dredges. Today, gold jigs have been replaced by high gravity gold centrifugal concentrators like those shown herein.
In BC, the solution to environmental problems with small scale placer gold mining, is to adopt more modern methodsusing gravity concentrators along with recirculation of processing water. The Placer Gold Mining Equipment described here can offer a step forward in meeting those goals and to improved disposal reclamation methods.
The first placer mining in the West was done by hand methods. As the rich surface deposits became exhausted other methods were substituted. Under normal economic conditions the hand-shoveling method is applied mainly to deposits that are too small to justify the capital expenditure necessary for working them by other methods. When work is scarce, however, any available gravel that will give a man a bare living may be worked in this manner. Because very little capital is required, men of small means can mine on their own account by hand-shoveling methods; in times of general unemployment, many such men go into the placer fields and search for and work surface gravels. This type of mining commonly is called sniping.
During the summer of 1932 thousands of men, most of them inexperienced, were mining in the placer districts of the West by hand-shoveling methods. They seldom earned a going wage but usually got enough gold to buy food. The average earnings of experienced men were estimated to be less than $1 per day and of experienced and inexperienced together less than $0.50. Occasionally a rich spot left by oldtimers would be found and as much as $100 might be cleaned up in a few days. These rare experiences, however, were offset by many days spent searching for a place to work or by wasted effort in digging to bedrock only to find it already cleaned or barren. During the autumn of 1931 many old bars in the rivers of the Pacific coast were exposed for the first time in years on account of the extremely low water of that season. Many snipers worked profitably on these bars until the fall rains raised the water level.
Snipers look mainly for unworked ground in or around old workings, or they extend old workings that have been discontinued as being unprofitable. They reclean disintegrated bedrock in old workings or clean out crevices in bedrock in river channels. They work old bars in the rivers where, reconcentration may have occurred since the early days of placering. Most of the ground worked by snipers, however, is ground that has been left by oldtimers as being unprofitable.
Most of the ground in the Western States known to contain placer deposits is owned privately or held under mining locations. A newcomer into a field generally has to obtain permission from the proprietor of the land before he can begin placer mining. Sometimes a royalty is charged; at other times hand mining is permitted free, the owners of the gravel doubtless considering that the prospecting value of such work equals the small amount of gold taken from the ground.
The water of most western streams has been appropriated for irrigation or power purposes., Placer miners should consider the previous rights of others in a stream before diverting any water for placer mining. The antidebris law of California prohibits uncontrolled discharge of placer tailings into any tributaries of the Sacramento River.
Panning is both the simplest and most laborious method of washing gold from placer gravel. With a little experience almost any one can recover most of the gold in a pan of ordinary placer dirt; an experienced man can wash about 10 pans per hour. As a man can dig gravel with a pick and shovel many times faster than he can pan it only the highest-grade gravel is washed. The top dirt usually is thrown aside, and a few inches of gravel on bedrock or material scraped from crevices is panned.
The standard gold pan used in the Western States is made of stiff sheet iron; it is 16 inches in diameter at the top and 2 inches deep. The rim is flared outward at an angle of about 50 from the vertical. Smaller pans are used for testing. Frying pans or other cooking utensils may also be used for washing out gold. Before any kind of a vessel is used for panning it should be cleaned thoroughly; all grease should be burned out. New pans generally are greasy and should be heated over a fire until all grease is burned off. A rusty pan if clean can be used satisfactorily; the roughness due to the pitting of the rust maybe of assistance in holding back the gold.
The pan usually is filled even with the top, or slightly rounded, depending somewhat upon the nature of the material being washed and the personal preference of the panner; it is then submerged in the water. Still water 6 inches to 1 foot deep is best. While under water the contents of the pan are kneaded with both hands until all clay is dissolved, and lumps of dirt are thoroughly broken. The stones and pebbles are picked out. Then the pan is held flat and shaken under water to permit the gold to settle to the bottom. The pan is then tilted and raised quickly so that some of the lighter top material is washed off. This operation is repeated, occasionally shaking the pan under water or with water in it until only the gold and the heavy minerals are left; this material concentrates at the edge of the bottom of the pan. Care must be taken that none of the gold climbs to the edge of the pan or gets on top of the dirt.
Nuggets and coarse colors can now be picked out readily. Cleaning the black sand from the finer gold is more difficult but can be carried nearly or entirely to completion by careful manipulation of the pan as described above, always watching carefully to see that none of, the colors are climbing toward the edge. This part of the operation usually is done over another pan or in a tub so that if any gold is lost it can be recovered by repanning.
The concentrates can be dried and the black sands removed by a magnet or by gentle blowing on a smooth flat surface. If there is an excessive quantity of black sand the gold usually is amalgamated by putting about a teaspoonful of mercury in the pan. In sampling work; great care is necessary that no fine colors are lost, but in mining by panning the extra time needed to make sure that no fine colors escape probably would not be justified. The loss of 50 or 100 fine colors in a day might not amount to more than 1 cent.
A standard 16-inch pan level full of dry bank gravel contains, on an average, 22 pounds. The quantity will vary with the moisture content and nature of the gravel. By allowing 3,300 pounds to the cubic yard (in place), 150 pans, would be equivalent to 1 cubic yard. The senior author has been accustomed to using this factor in sampling placer deposits. At 3,600 pounds to the cubic yard and 22 pounds to the pan, 164 pans would be required to wash a cubic yard of gravel. At 10 pans per hour a man could pan about cubic yard in a day. With exceptionally clean gravel a man will sometimes pan as much as a cubic yard in a day.
More gravel can be handled, per man-day by rocking, or cradling as it is sometimes-called, than by panning. Moreover, the manual labor of washing a cubic yard is less. The same method of excavating the gravel is used whether it is panned or rocked. The rocker like the pan, is used extensively not only in small-scale placer work but also in sampling and for washing sluice concentrates and material cleaned by hand from bedrock-in other placer operations.
One to three cubic yards, bank measure, can be dug and washed in a rocker per man-shift, depending upon the distance the gravel or water has to be carried, the character of the gravel, and the size of the rocker. Rockers usually are homemade and have a variety of designs. A favorite design in the Western States consists essentially of a combination washing box and screen, a canvas or carpet apron under the screen, a short sluice with two or more riffles, and rockers under the sluice. The bottom of the washing box consists of sheet metal with holes, about one half inch in diameter punched in it. A rocker in use at Greaterville, Ariz., was.3 feet 4 inches long and 1 foot 9 inches wide on the inside and had a slope of 5 inches. The screen box was 6 inches deep and 20 inches square inside and had a bottom of sheet iron with - to -inch holes punched about 2 inches apart. The baffle was 28 inches long and consisted of a piece of canvas. A single riffle inch high was used at the end of the rocker. Figure 3 is a drawing of a prospectors rocker made by W. B. Young of Tucson, Ariz. The bottom of a rocker should be made of a single wide board, if one can be obtained, and planed smooth. This will greatly facilitate clean-ups. The cost of building rockers ranges from $5 to $15, depending mainly upon the cost of lumber.
After being dampened the gravel is placed in the box 1 or 2 shovelfuls at a time. Water is then poured on the gravel while the rocker is swayed back and forth. The water usually is dipped up in a long-handled dipper made by nailing a tin can to the end of a stick. A small stream from a pipe or hose may be used if available. The gravel is washed clean in the box and the oversize inspected for nuggets and dumped out. The undersize goes over the apron, where most of the gold is caught. Care should be taken that too much water is not poured on at one time, as some of the gold may be flushed out. The riffles stop any gold that gets over the apron. In regular mining work the rocker is cleaned up after every 2 or 3 hours, or oftener when rich ground is worked, if gold begins to show on the apron or in the riffles. In cleaning up after a run, water is poured through while the washer is gently rocked the top sand and dirt are washed away. Then the apron is dumped into a pan. The material back of the riffles in the sluice, is, taken up by a flat scoop, placed at the head of the sluice, and washed down gently once or twice with clear water. The gold remains behind on the boards, whence it is scraped up and put into the pan with the concentrate from the apron. The few colors left in the sluice are caught with the next run. The concentrate is cleaned in the pan.
With skillful manipulation of the rocker and a careful clean-up nearly all the gold is recovered. Violent rocking, is avoided so that gold will not splash out of the apron or over the riffles. The sand, behind the riffles should be stirred occasionally, if it shows a tendency to pack hard, to prevent loss, of gold. If the gravel is very clayey it may be necessary to soak it for some hours in a tub of water before rocking it.
When water is scarce two small reservoirs are constructed, one in front and the other in the rear of the rocker. The reservoir at the front serves, as a settling basin; the overflow goes to the one at the rear where the water is used over again.
Power rockers.- The capacity of rockers may be increased by using power drives. The use of such a machine was illustrated by the operation of George Graves in the Lynn district, Eureka County. Nev., during the summer of 1932. The rocker was 49 inches long, 27 inches wide at the top, and 21 inches wide at the bottom. It was 24 inches high in front and 21 inches at the rear. The screen had 5/8-inch round holes. The gold was caught on three aprons of canvas and wood. Riffles of - by -inch wooden strips were used on the aprons. The undersize from the screen passed over each-apron in turn. Nearly, all the gold was caught on the first apron. The slope, of the aprons was 3 inches to the foot.
The device was rocked by an eccentric arm at the rate of forty 6-inch strokes per minute. The capacity of the machine with two men working, was 1 cubic, yard per hour. Where gravel was free of clay the capacity was said to be as great as 3 cubic yards per hour. The cost of the rooker and the engine for driving it was $160. At $4 per 8-hour shift and 1 cubic yard per hour the labor cost of washing the gravel would be $1 per cubic yard.
A number of small, machines patterned more or less after the power rocker are on the market. They usually are built of iron, or steel and driven by small gasoline engines. Although of various designs they generally consist of a trommel or a shaking screen to remove coarse material, a short shaking sluice to save, the gold, and a pump to circulate, the water. Some of them contain a settling tank from which the solids are removed by a rake or drag. These machines have an advertised capacity of to 2 cubic yards per hour and cost $225 to $700. No operating data are available.
A long tom usually has a greater capacity than a rocker and does not require the labor of rocking. It consists essentially of a short receiving launder (see fig. 4), an open washing box 6 to 12 feet long with the lower end a perforated plate or a screen set at an angle, and a short sluice with riffles. The component boxes are set on slopes ranging from 1 to 1 inches per foot. The drop between boxes aids in breaking up lumps of clay and freeing the contained gold.
A good supply of running water is required to operate a long tom successfully. The water is introduced into the receiving box with the gravel, and both pass into the washing box. The sands and water pass through the screen, which has about -inch openings into the sluice. The oversize is forked out. The gold is caught by the riffles. The riffle concentrates are removed and cleaned in a pan. Quicksilver may be used in the riffles if the gravel contains much fine gold.
The quantity of gravel that can be treated per day will vary with its nature, the water supply, and the number of men employed to shovel it into the tom and fork out the stones. Wilson states that 2 men, 1 shoveling into the tom and 1 working on it, can wash 6 cubic yards of ordinary gravel, or 3 to 4 cubic yards of cemented gravel, in 10 hours. At times the tom is operated by 4 men, 2 shoveling in, 1 forking out stones, and 1 shoveling fine tailings away. Toms are rarely used now in the United States; where running water and grade are available a simple sluice is generally as effective and requires less labor.
A modified form of long tom has been employed for washing beach sands at Nome, Lituya Bay, Yakataga, and Kodiak, Alaska. For saving fine gold the box is set at a high gradient, 3 to 4 inches per foot, and the screened material is passed over riffles and amalgam plates. The water for sluicing generally is bailed with a large dipper. The average duty per man per 10 hours for long-tom or rocker workon beach operations is 3 to 5 cubic yards.
Surf washers are similar to long toms but are wider and shorter. They can be used only when the surf is of proper height. They are set so that the incoming surf rushes up the sluices, washes material from the screen box or hopper, and on retreating carries it over the riffles and plates. One man can attend to two surf washers, and in one instance 8 cubic yards was handled per 10 hours.
A simple surf washer used about 1902 at Topkuk, Alaska, was a riffled sluice 3 to 4 feet wide and 8 to 10 feet long, set on the sand at the waters edge so that the incoming waves washed through it to the upper end yet retreated below the lower end. The sluice was made of boards nailed to sills at either end which could be weighed down with rocks or otherwise. The sides were only 4 or 5 inches high. The riffles, similar to those used on dredges, were made in sections of about 1- by 1-inch strips and were spaced about an inch apart. The end sections were transverse riffles the center section was longitudinal. The box preferably was set on a grade of 8 to 10 inches per 12 feet. Best results were obtained by using quicksilver in the riffles. It was stated that when the surf was strong the washer would treat as much as two men could shovel, but that at other times it had to be fed very slowly.
Dry washers have been used for many years in the Southwest where water is scarce, especially in New Mexico where probably 3 or 4 million dollars in gold has been produced during the last century by dry-washing, A small steady production by dry washers still comes from, the Cerrillos, Golden, and Hillsboro districts each year. In years when other employment is scarce the production increases. During 1931 and 1932 a considerable number of men also used dry washers in Nevada, southern California, and Arizona.
Gravel to be treated successfully by dry washers must be completely dry and disintegrated. With dry washers operations must be stopped after rain storms until the ground dries out again. The only successful dry washing up to 1932 has been on a small scale. Plants with mechanical excavators and extensive power-driven dry-washing machinery have been tried, but in the United States none has been commercially successful, partly because in large-scale work the gravel is dug faster than the sun can dry it out. Even in very dry climates the gravel is slightly damp below the surface and must be dried before it can be treated in a dry washer. Spreading the material to sun-dry or putting it through driers adds to the cost of mining. In small-scale work the gravel dries out as fast as it can be treated.
Individual workers select the material they treat with regard to both dryness and probable gold content; it is difficult to do this on a large scale with hired labor. In large-scale work, particularly with mechanical excavation, the cost of sizing the material is an important item; clay and cemented gravel introduce further difficulties.
Dry washers usually are run by hand and have about the same capacity per day as rockers of a corresponding size, but the work of operating the dry machine is much harder. When the gold-bearing material is completely dry and disintegrated, panning tests of the tailing show that a good saving can be made, except perhaps with extremely fine or flaky gold. Completely disintegrated material, however, seldom is obtained. The tops of clay streaks in the gravel are likely to be richer in gold than the gravel itself. Clay or cemented gravel seldom can be broken up sufficiently by hand to free all the gold without the use of some form of pulverizer. In a dry machine all gold included in a lump of waste passes out of the machine. As water usually breaks up all the gravel and separates the gold from the other material a better saving generally can be effected by rocking or in sluice boxes than in a dry machine.
The basic principle of the dry washer is separation of the gold from the sand by pulsations of air through a porous medium. The screened gravel passes down an inclined riffle box with cross riffles; the bottom of the box consists of canvas or some other fabric. Under the riffle box is a bellows by which air in short, strong puffs is blown through the canvas. This gives a combined shaking and classifying action to the material; the gold gravitates to the canvas where it is held by the riffles, while the waste material passes out of the machine.
The gravel is shoveled into a box holding a few shovelfuls at the head of the washer whence it runs by gravity through the machine. A screen with about -inch openings is used over the box; all stones over about 1 inch in diameter generally are discarded in mining. One man working alone fills the box, then turns a crank which runs the bellows until the gravel is run through the process is then repeated. With two men working, one shovels and the other turns the crank. One man can treat to 1 yard per day with a hand-operated washer where the gravel is handy to the machine. Some dry washers are run by a small gasoline engine which saves the labor of one man the capacity of such machines is considerably greater than that of hand-operated machines.
In cleaning up, the material back of the riffles usually is dumped into a pan and washed out in water. If water is very scarce the accumulated material from the riffles may be run through the machine a second time and then cleaned further by blowing away the lighter grains of sand in a pan.
Dry washers usually are handmade and have a large number of designs and sizes. Figure 5 is an isometric drawing of a machine built and run by E. C. Spurr on Goler Gulch near Randsburg, Calif., in June 1932. The bellows of the machine is made of 36-ounce duck and the bottom of the riffle, box of 8-ounce single-weave canvas. Spurr has found by long experience that the 8-ounce material is the best for the purpose. Silk or rayon permits a good extraction of gold, but too much dust goes through into the bellows. Heavier canvas is too tight for good separation. Copper-wire fly screen is used under the canvas. The riffle box is 11 inches wide and 40 inches long and contains 6 riffles. The type of riffle is shown in figure 5. The slope of the riffle box is 5 inches to the foot. The gravel and sand are shoveled onto a screen with 3/8-inch square openings at the top of the washer. The machine is run by a -hp. gasoline engine. The bellows is operated at 250 pulsations per minute; the stroke is 3 inches. The capacity of the machine was 1 cubic yard in 1 hours or 0.8 yard per hour. This probably would correspond to 1 or 2 cubic yards, bank measure, on account of the plus 1-inch material having been thrown out in mining. The gravel had been collected in an old drift mine, and carried out in buckets; 3 hours were spent by one man in getting out the gravel.
In cleaning up after running a cubic yard through the Spurr washer the riffle box was lifted out and turned over on a large, flat, baking tin. The concentrate from the upper three riffles was first panned and the gold removed; both coarse and fine gold were saved, the total being worth about 75 cents. The lower four riffles had one good-sized color and a few small ones. Nearly all the gold was caught in the upper riffles; this indicated that a fair saving was being made of the free gold.
Mining.- Shoveling-into-boxes is a small-scale placer-mining method in which the gravel is loosened by picking and is shoveled by hand into sluice boxes. It is particularly adapted to small, shallow, moderately rich deposits where only a little water is available or where the grade is insufficient to allow room for disposing of the tailings unless the gravel is elevated. If the water supply is adequate the ground-sluicing method (described later) should be considered, and if the deposit is large enough to justify the required capital investment some other method such as hydraulicking or dredging would be preferable.
The quantity of water available will influence the scale of operations and the size of sluice used. A minimum flow of 15 to 20 miners inches (170 to 225 gallons per minute) is required for a 12-inch sluice box with a steep grade. Smaller flows than this can be utilized by reservoiring the water and using an augmented flow. A common practice followed where the quantity of water is limited is to place a grizzly or screen over the sluice and thus increase the duty of the water. A head box with sloping sides and a grizzly near the bottom may be used for receiving the gravel. In this case the oversize is forked out. In one Nevada operation the gravel first was run through a trommel to wash it and screen out all coarse material. Puddling boxes may be used if the gravel contains much clay. If the ground is of good grade it may be practicable to pump water for the sluice the feasibility of obtaining a gravity flow, however, should first be investigated, as the mining expense due to pumping may be.more than the cost of a ditch distributed over the yardage moved,
Water usually is conducted in a ditch to the sluice which is set up in the most advantageous position to begin work. Boxes are 8 to 24 inches wide and range from 3 to as many as may be required to transport the tailings to a suitable dumping ground; they are laid on sills at approximately the mean elevation of the surface of the deposit. If enough water is available 6 or 8 inches per 12 feet, is a good grade with most types of gravel. If water is scarce or the gravel angular a steeper grade will be desirable; the grade should be uniform. The best type of riffle depends on the nature of the gravel and the gold rather than on the method of extraction. An end shake was given to the box at a mine in Arizona to increase its capacity. Water was hauled for washing. Riffles are discussed in a subsequent paper.
The cost of boxes depends chiefly on the cost of lumber delivered to the property, which may range from $15 to $60 per 1,000 board-feet. A 12-foot box, 12 inches wide, constructed of three 1- by 12-inch boards with three sill frames of 2 by 4 lumber, requires.about 45 board-feet of lumber. If clear lumber costs $35-per 1,000 board-feet the cost of a set of five boxes would be about $8.00. Material for riffles may cost little or nothing or as much as $1 per box.
After the boxes are set, shoveling begins at an advantageous point. All material of a size that will run. through the sluice is shoveled in and the oversize is thrown to one side. Boulders from the first cut should be stacked outside the pit, on barren ground if possible. The width of a cut usually is limited to the distance a man can shovel in one operation. When shoveling from any distance it is best to set boards above and on the opposite side of the box; these increase the efficiency of the shovelers. The greatest height a man can shovel into a box is 7 to 8 feet above 5 or 6 feet the efficiency of the shovelers is reduced markedly. If over 3 or 4 feet in depth the gravel usually is excavated in benches to facilitate digging and at the same time to permit the upper layers of gravel to be raised a minimum height. Where the gravel is shallow wheelbarrows may be used. At a Nevada mine the gravel was shoveled onto a conveyor belt which discharged into a trommel. The oversize was discarded, and the undersize ran through a sluice. Where two or more men are working in the same cut the heights of succeeding benches are governed by the character of the material being dug and the distance the gravel has to be lifted. Work may begin at one edge of the deposit and proceed across it by regular cuts. The sluice may be maintained on the surface of the unworked ground or on bents on the opposite side of the cut. After the first cut the boulders are thrown onto the cleaned-up bedrock. Where cuts are run on both sides of the sluice the boxes are supported on bents, as the ground underneath them is dug out. At other places the boxes may be set on bedrock and all dirt shoveled into the head of the sluice from short transverse cuts at the upper end of the pit. Work visually begins at the lower end of a deposit so that bedrock maybe kept drained. The length and order of making the cuts will depend upon local conditions.
Experienced miners, work out the ground in regular cuts and in an orderly fashion. Enough faces are provided so that shovelers will not interfere with one another. Provision is made to keep bedrock drained, and boulders and stumps are moved a minimum number of times. Cuts are taken of such width and length as to make the shoveling as easy as possible. The boxes are kept, at such a height, that the minimum lift, of the gravel is required consonant with, enough fall for the gravel to run through the boxes with the water available and to allow dump room at the tail, end of the sluice. Leaks in the sluice are stopped promptly, and shoveling is done in such a manner that the sluice does not become clogged or water splashed out. Water in the pit hampers shoveling.
of gravel per shift into boxes 3 or 4 feet above bedrock. Where the gravel is tight and coarse and the bedrock rough, he may be able to shovel only a yard a day. The time necessary to construct, set up, and clean the sluice boxes and to clean bedrock reduces the average performance of men shoveling into boxes to about 4 yards per shift.
Cleaning bedrock.- When a sufficient area of bedrock is exposed it is cleaned up carefully. If the bedrock is easy to clean this may be done as the work progresses up a cut. In such ground if the gravel is shoveled in benches by two or more men the man who takes up the lower layer of gravel may clean the bedrock as he goes along. If the bottom is difficult to clean a full cut may be taken before the bedrock is given the final clean-up.
After all loose gravel is shoveled into the boxes the bedrock should, if possible, be taken up with pick and shovel to a depth of 6 inches or more and likewise put into the sluice. Any large rocks near bedrock should be washed off before they are thrown aside, because clay adhering to them may contain gold. If the bedrock is decomposed or soft, or if there is a false bedrock, this process will recover practically all the gold.
If water can be taken from the sluice or ditch through a hose under low pressure all loose material missed in shoveling will be washed down to a hollow where it will be collected and placed into the boxes or in a rocker. The bedrock then is scraped and swept, and the crevices are cleaned out finally it may be washed a second time.
If it is not convenient to use water the bedrock may be cleaned up dry. The bedrock is swept, scraped, then swept a second time; the crevices are cleaned out as before. The sweepings and scrapings, together with the material from the crevices, are washed either in the sluice or in pans or rockers. Large colors or nuggets are picked up as found.
The tools used for the hand work are picks and shovels, brooms, small stiff brushes, perhaps a sponge to dry out hollows, and hand scrapers of various sizes and shapes, ranging from sections of old frying pans to knives, spoons, or bent wire for cleaning narrow crevices.
In small operations, such as the typical 3- or 4-man ground-shoveling venture, cleaning bedrock is carried to greater extremes than in larger mines where labor is hired, as the incentive to careful work is greater and the yield necessary to encourage further cleaning is less, Skilled and careful crevicers have been known to make fair wages on bedrock abandoned by organized mining companies. The miner should therefore be sure his cleaning operations have been carried to the point where he is no longer getting enough gold to recompense his efforts.
As previously defined, ground-sluicing is a placer mining method, in which gravel is excavated by running water not under hydraulic pressure. In some cases water is stored in reservoirs, and greatly increased flows are discharged during short periods. This variety of ground-sluicing is termed: booming by placer miners and is so called in this paper. The action of the ground-sluice water may be augmented by hand work or by a jet of water under pressure. However, if hydraulic monitors or giants perform most of the work the method becomes hydraulicking, described in a later paper.
With a few exceptions ground-sluicing is used in small operations by miners with little capital. Otherwise it is used only where water under a substantial head is not available or where the gravel deposit is too small to justify building ditches or installing pipe lines for hydraulicking. The chief application of ground-sluicing is to deposits in or near stream beds. If applied to higher gravels pipe lines, flumes, or ditches are necessary, and the method loses one of its chief advantages, a low initial cost.
Ground-sluicing is not adapted to mining large deposits of tight or cemented gravel these demand the tearing, disrupting force of giants. Gravel containing large boulders can be ground-sluiced, but more labor is necessary than if hydraulicking is used; the ground-sluice water seldom loosens and transports as large boulders as a giant or as large ones as will run through the sluice.
At many places no preliminary development work is necessary at others long cuts must be run to reach bedrock under the deposit. If booming is to be done a dam must be built for a reservoir and perhaps an automatic gate. A sluice box is always used, although in many mines for little more than as a race to carry away the tailings. In bouldery ground derricks or drag lines may be needed to remove boulders.
A large number of small ground-sluicing operations were being carried on during the 1932 season by groups of 1 to 4 men working for themselves. Enough gold to pay regular wages was obtained at very few of the operations. Usually the miners received less than $1 per day for their efforts. A few larger operations have been carried on for a number of years; some of them have been profitable. Essential data concerning the larger mines and representative smaller ones operated in 1932 are shown in table 7. These mines are described in more detail later. They illustrate the applications of the method and general ground-sluice practices.
Except for the Osborne lease at Superior, Mont., gravels of moderate thickness along stream beds were being worked by ground sluicing at the mines listed in table 7. The depths of gravel ranged from 5 to 22 feet. Except at two placers very little of the gravel was tight, and none of it was cemented. At these, the Rundle and Morgan placers, Blackhawk, Colo., the gravel was tight and had to be loosened by picking; however, most of the material mined was overburden which was easily ground-sluiced,
The water supply was limited at most of the mines worked by ground-sluicing. At the Rundle and Morgan placers more water was available in the creek than could be used to advantage, because the gravel had to be loosened by picking. As noted in table 7, 60 to 500 miners inches were used at the various mines listed. The natural flow of the streams ranged from 10 to 500 miners inches.
Ground-sluicing has an advantage for running bedrock cuts in that a relatively small capital expenditure is required to test the gold content of the gravel and to ascertain the mining conditions. Cuts made in this manner also open up the deposit for mining. A relatively low yardage per shift is obtained in such work. A large part of the expense of running such cuts is the construction of the sluice, which will be used if the deposit is mined later. The work at the Rundle, Osborne, Kamloops, Willow Creek, and Magnus mines, at the time the authors visited them, consisted of running bedrock cuts.
At the other seven properties strictly mining operations were under way. Regular ground sluicing can be subdivided further according to the manner in which the water is used: (1) Water poured over the upper face of the cut and (2) water directed along the bottom of a straight or curved bank. Under (1) the cascading effect of the water is utilized to break down the gravel, or the fall of the water from a projecting flume or pipe is used to cut the bottom layer. Under (2) the current is used to undercut the bank and carry away the broken gravel at the face as it breaks down. The depth of the gravel has an important bearing on the practice followed; with thick deposits the cascading or falling of the water over the upper face is likely to give the best results; in thinner gravels the other method is usually advantageous. The width of the deposit is also a factor in narrow channels the first method would have an advantage over the other. As shown by table 7 the thickness of gravel at the Morgan, Bar No. 2, and Harvey placers where the water was brought over the face was 5, 6, and 22 feet, respectively. At the other four placers, Ravano, Bar No. 1, Camp Bird, and Bennet the depth of gravel was 6, 6, 10, and 15 feet, respectively.
Of the 12 mines listed in table 7 sluicing with the natural flow of the stream was followed at 3. At 5 properties a minor part of the water was used under pressure, and booming was practiced at 5 not counting the Ravano. In one placer (Camp Bird) a hose was used for cutting the bank and the broken gravel removed by booming.
The water may be directed against the bank in a channel made by piled boulders or by, boards. It can be diverted conveniently to any desired point or direction by means of what are called shears. These consist of 1- or 2-inch boards 12 feet long nailed to two tripods which slope back from the water flow at an angle of about 60. The tripods are of pointed poles about 4 feet long and so constructed that boulders may be piled on the base to hold them in place. A row of shears may be used to direct the force of the water .against a bank, or two rows may be used to form a flume.
Of the multitude of snipers working on the creeks in the summer of 1932 many washed their gravel by ground-sluicing with the natural flow of the stream. The only equipment essential for this type of work in shallow gravels is a few 12-foot sluice boxes and picks and shovels. Table 7 shows that 2 , 9, 3, and 9 cubic yards, respectively, were handled per man-shift at the first four mines in the table where the natural flow was utilized. At the Morgan placer water running down the face of a narrow cut was used to carry the fine material in the gravel to the box after it was loosened by picking. At the Ravano a cut was made first down one side of the area to be washed during the season and then extended across the channel. The water was directed against the bank by means of dams. Although a reservoir was used and the stream of water was augmented for a half shift each day the mine is placed under this class, as it is representative of a large number of operations where only
the natural flow was utilized. At the Bar No. 1 the water was brought down over the face. At the Osborne deeper gravels were mined, and the water cascaded down the face of a cut. Boulders were removed by a power derrick.
Where part of the water can be brought into the workings under pressure through a pipe the nozzle may be used to replace hand-picking in loosening and disintegrating the gravel. It may also be used to replace part of the hand labor in cleaning up bedrock. The ground-sluice water washes the gravel into the boxes; it also breaks down the bank to various degrees at different mines. The actual sluicing operations are quite similar whether or not water under pressure is used.
At the Rundle, Bar No. 2, and Kamloops mines, where pressure pipes were used the head of the water ranged from 6 to 60 feet, as shown in table 7; nozzles 1 and 2 inches in diameter were employed. The yardage moved per man-shift was 3, 12, and 18, respectively,
Booming utilizes the increased cutting and transporting power of water under flood conditions. As pointed out, water is stored in a reservoir and then released, flowing for relatively short periods. At the beginning of the season, when high water prevails, the booms may occur frequently, and each one may last relatively long. As the supply of water fails booms occur less often until finally there is not enough water to operate. Booming is the most important type of ground-sluicing. A much larger duty can be obtained per unit of water by booming than by other forms of ground-sluicing. The increased volume of water carries boulders into the sluice that otherwise would have to be moved by hand or by power and breaks down the banks against which a smaller stream would be ineffective. Larger sluice boxes must of course be used when booming than when utilizing only the natural flow of the stream.
Booming is used in running development cuts as well as in strictly mining work. Of the three strictly mining operations listed under this head a side cut was used in two and an overcast at the end of the pit in the third.
The duration of a boom is governed by the size of reservoir and the flow of water. The capacity of the reservoir should be governed by the character of the ground. In heavy, rocky ground a short period with a correspondingly larger surge is more effective than a longer period with a smaller stream. In other ground, such as that at the Camp Bird mine, longer periods of washing, with correspondingly less water, give the best results. Reservoirs usually are constructed by building a dam across a narrow part of the stream bed or canyon and backing the water up behind it. Ordinarily, earth dams with a board facing on the upstream side are used. Reservoirs with capacities of to 1 acre-feet (table 7) are used at the mines listed. Automatic gates have a double advantage in that no labor is required to operate them and the booming in the pit can continue 24 hours each day. Automatic gates are shown in figure 7. Although the water is not as effective when unattended as when the miners are on shift it accomplishes considerable work during off hours.
mining 101: ultimate list of gold mining equipment - precious metal info
Found in Bulgaria are some of the oldest gold artifacts known to mankind, in the Varna Necropolis, a collection of graves built between 4700 and 4200 BC. This finding, dating back nearly 7000 years, provides evidence of the first civilization to use gold mining equipment. Some archeologists claim the Sakdrisi site in southern Georgia, which dates to roughly 4000 BC, is the worlds first gold mine.
In the 19th century, gold rushes occurred around the globe and people migrated to different regions hoping to strike it rich. The Victorian Gold Rush took place in Victoria, Australia, between 1851 and the late 1860s, and the Second Boer War took place in South Africa between 1899 and 1902. In America, the famous California Gold Rush took place in 1949, and discovery of Nevada's Carlin Trend,North America's largest gold depository,took placein 1961.
Since the beginning of civilization, humans have mined around 6 billions troy ounces of gold. Today, 2.5 percent of all gold production happens in Nevada, making it one of the primary regions on earth. As of 2017, China produced the most gold per year at 429 metric tons, followed by Australia, and then Russia. However, there's still a lot of gold out there, and you can join in the gold mining industry by investing in basic gold mining equipment.
There are two basic steps to gold mining: prospecting and production. "Prospecting" refers to the actual search in a certain area for valuable minerals, and "production," also known as mining, is the physical act of removing the gold from where you found it. Since different equipment exists for prospecting and mining, this article explores, briefly, equipment used for prospecting, and then focuses, primarily, on gold mining equipment.
How do you find gold? In the gold mining industry, theres a lot of value in learning from others who have gone before you. No one ever gets all the gold out of any one location. So, try going to where gold exists in abundance. Consider this: the California Gold Rush only removed a small percentage of the gold thats out there. That's right.
There are areas in California that are still open to recreational prospecting, including the Auburn State Recreation Area and the South Yuba Recreation lands. Once you get your feet wet in an area proven to have gold, you can move on to other areas closer to home. After mastering prospecting and gold-mining techniques, you might even want to look for gold in your own back yard.
Some people say, Gold is where you find it. What this means is you have to learn what to look for. First, understand that the way water moves in rivers and streams determines where gold deposits might settle. Next, you need to learn why gold concentrates in certain areas, and then search those areas.
Once youve selected a specific waterway for mining, youll want to pick specific points to search. Since it is impractical to search the entire stream or river, there are ways to read a waterway to determine the most likely places to find gold. The following describes how to find those places.
The first thing to know is gold is heavy. Its about 19 times heavier than the same amount of water and 6 times heavier than solid material found in streams and rivers. So, anything that slows the movement of water is likely to trap gold deposits. Things that slow down moving water are:
Water on the downriver side of obstacles will move slower, and this is where heavier gold will settle. When looking at a chosen waterway, begin by searching for natural dams where gold may have collected. Another place that collects heavier objects in a waterway is inside bends, places where water naturally slows down. Heavy objects will often form a bar at these points, and the upside of a bar inside bends is a great place to look for gold.
Once gold has settled in a stream, over time, it works its way down layers of soil and settles in bedrock. A great location for gold is in the material coating bedrock under a stream. Choose a location on the inside a bend where there is an obstruction and then dig to the bedrock. Sifting the soil coating bedrock, usually, will produce gold.
Learn to delay the excitement of seeing gold for the first time and you will have more gold-filled dirt to take home with you. Once you get better at choosing locations, and especially if you find a proven location, its best to spend your time digging and removing dirt, rather than sifting and cleaning it on site. Delay celebrating and get as much dirt as possible to take home. Once you get home, sift and clean the gold youve found.
Another great place to look for gold is in tall grass growing above an inside bend. Grass acts like a sieve and the largest gold pieces end up at the roots of grass. They often call this kind of gold oat gold. The pieces might be smaller than gold found in other places, but there could be a lot.
If you want to invest a little in your endeavor, you can purchase a metal detector designed to find gold. This gold mining equipment can cut down on the time spend hunting, but a mid-level detector can cost about $600.
When considering getting involved in gold prospecting and mining, make sure you learn and follow the rules. There are certain places where prospecting is legal and others where it is not. Many prospecting clubs exist and joining one can help ensure you are following rules. For examples, most sites require that you refill any holes you have dug, and that you do not destroy local plant life. Learn the rules before you head out with your gold mining equipment.
Once youve finished prospecting and have a location where you know there is gold, you will need gold mining equipment. What you use will depend on the size of your operation. If you are working in the gold industry, you will have industrial gold mining equipment. If you are mining on your own as a hobby, youll need smaller, personal gold mining equipment. Lets look at both.
If you want to use industrial mining equipment, make sure you have the proper training. If working for a business, they should provide needed training. However, if you purchased industrial gold mining equipment for a personal claim, be certain you know what you are doing. Safety should always come first.
Miners use drills for underground mining to create access holes for descending underground, or to place explosive charges to bring material to the surface. The drill miners choose depends on how and what is being mined.
Blasting tools create an explosion to blast away chunks of material to access minerals. Blasting can also remove chunks of unwanted materials that are keeping other machines or people from getting to a seam of wanted materials. In underground and open pit mines, miners use both drilling and blasting tools, often together. They use drills to place blasting tools at the right depth and in the right place.
Earth-moving machines move around large amounts of materials. They might haul material after blasting, move other materials allowing access to seams of minerals, dig underground mines, or get down to the bedrock where minerals might exist.
Crushing equipment moves materials around an underground mine. Miners use this equipment to keep the flow of materials going at an efficient rate, and to save money. It is easier to remove crushed rocks rather than heavy chunks, so crushing equipment saves time and effort.
A sluice box is a way to sift through raw material more quickly. Essentially, its automated panning. These machines used to be large and heavy in the early days of panning, but are now lightweight and easier to use. If youre serious about mining, they are worth checking out.
A higher quality sluice box, high banker boxes have a water pump allowing more material to move through faster. These boxes recycle water so you dont have to rely on water flow in the river. They recover more gold than basic models.
If you arent going into the professional gold mining industry, but are looking for a hobby or a part-time job to bring in a little extra money, consider joining a mining club to help you once you begin your prospecting journey. The club will help you learn about personal gold mining equipment, but, for now, lets take a quick look at what you will need.
There are lots of different sizes, colors, and options in gold pans. Essentially, a 14-inch plastic pan is the best size, by far. Color does not matter, however gold shows up better in black. Black sand shows up better in blue or green. There are many new kinds of pans, but a basic pan with sharp, undercut riffles is all you need. Make sure the bottom of the pan is as wide as possible to catch more gold.
You will need a place to store the gold you find. All you need is a waterproof container you can close tightly, such as a 35mm film container. You can purchase containers on the internet, specifically made for holding gold.
The last thing to consider is investing in Gold Lab, a personal system that recovers gold from the concentrate you have refined. A good gold panner can get most of the gold from refined dirt, but a Gold Lab kit will allow you to further refine and recover 100% of your gold.
Once you have your equipment, its time to get in the river to pan for gold. This simple technique mimics what the river does naturally. You recover material, or dirt and place it in the pan, from a river location where you think there might be gold. Then, you shake it in a left-to-right motion underwater to sweep away light materials while causing heavier materials to go to the bottom of the pan.
Take the pan with the riffles on the far side and shake it, vigorously, left and right. This breaks up materials sending heavier items to the bottom. Do not slosh water out of the pan. If you need to, repeat the previous step and break up larger chunks again.
Continue shaking the pan back and forth and keep removing the top layer of lighter materials until you are down to only the heaviest materials, such as coins, BBs, old bullets, buckshot, nails, garnets, black iron rocks and black sand. You should now be able to see gold in the pan when shaking and tilting it forward slightly.
Use a magnet to remove black sand and other metal objects. Keep removing things until only gold remains. Remove the larger gold pieces and save any leftover concentrate. Let it sit for a while so you can recover any remaining pieces of gold that settle.
If you have enjoy the outdoors, and have just a little ambition, you can make a hobby out of gold prospecting and mining. All you need are basic tools that as your gold mining equipment and the willingness to do a little research. Once you decide where to go, or join a mining club to help you find locations, pack up your tools and prospect. It may take practice at panning before you find anything, but once you do, youll love the feeling of satisfaction and discovery. If you find you enjoy the hobby, invest in semi-professional gold mining equipment and see if you can up the amount you discover. Even if you only discover a few flakes, prospecting can be a great way to make new friends, learn about the gold industry, and understand a little about gold prospectors of old. Its an inexpensive hobby, so grab basic gold mining equipment and get started today.
911MPE has for target market what mining professionals consider the pilot-plant scale mining operation or artisanal mining operations with a focus around under 500TPD. Metals you can extract include: gold, silver or other of the precious group as well as the classic base metals; copper, lead, zinc, nickel, molybdenum. Much of our ultra-small scale equipment allows you to process from just a few kilo (pounds) per day and work on your passion for a small budget.
new and used trommels for sale | gold trommel design & manufacturing by savona equipment
New and Used Gold Recovery Trommels for SaleSavona Equipment is your source for New, Used, and Reconditioned Trommels for recovering gold and other precious metals from placer mining operations. We supply 18 inch, 30 inch, 48 inch, 60 inch, & 7 foot Trommels for Placer Mining. Refurbished trommel parts will be fully repaired or replaced as required.Our Trommels and Gold Recovery Equipment are for sale worldwide. We sellPortable GoldTrommels, MiniWash Plants, andGoldTrommel Wash Plant.You Can Buy Various High Quality Gold Trommel Wash PlantProducts from various GoldTrommel Wash Plant manufacturers like Telsmith, McCloskey, Northern Placer, Aureco, Extrac-Tec as well as order a custom made gold recovery wash plant designed, manufactured, and distributedby Savona Equipment.
gold mining equipment | diamond mining equipment | dove
DOVE Diamonds and Gold mining equipment are configured for different ore type, laterite, heavy clay, gravel and black sand. Wash plants are designed for highest recovery and minimum operator requirements.
DOVE is a major manufacturer of hard rock gold mining equipment, and hard rock mining equipment, and crushing plants for base metals, ferrous metals and light metals, producing Ball Mills, Jaw Crushers, Cone Crushers, Magnetic Separators, Shaking Tables, Gold Concentrators, Rotary Dryers, and Flotation Process.
Each processing plant is designed tailor made according to the ore characteristics and the mineral composition of the ore, and designed for the 100% recovery of gold and other metals production, with no loss.
DESERTMINER is a Dry Mineral Processing Plant developed by DOVE to simultaneously concentrate, separate and recover gold, platinum group metal, base metals, ferrous metals from Alluvial deposits, as well as Hard Rock deposits, that are located in dry areas, where water not available.
DESERTMINER is designed and configured to deliver a high efficiency in mineral processing, with 100% recovery of gold and other metals and minerals, with no loss, similarly to the wet mineral processing plants.
DOVE designs and manufactures high recovery Beneficiation Plants. Beneficiation plants are composed of different types of machines and separators depending on the metals and minerals composition and characteristics, designed for high economic recovery in a customized configuration that will meet the projects specifications. These plants can include Flotation Machines, Dryers, High Intensity Magnetic Separators, High Tension Separators, etc. They can be used for both hard rock (primary) and alluvial (secondary) deposits.
DOVE supplies the state of art inGold Refinery technology, which is designed to produce and refine raw gold production to international standard purity of 999.95. DOVE refining units are supplied in capacity ranges of 6 kg up to 150 kg. The units are based on advanced Aqua Regia process and it is designed to refine gold, silver, copper. The refining units are configured with the latest technology to comply with the highest environmental standards, which includes neutralization towers for fumes, etc.
Every mining operation requires sophisticated gold room in order to ensure the highest recovery of gold production. To this end DOVE supplies and manufactures a complete range of equipment, instruments, tools and accessories, which includes Gold Concentrating Table, Gold Centrifugal Concentrator, melting furnace, crucibles, ingot molds, scales, and assay instruments.
DOVE supplies Flame Atomic Absorption Spectrometer (AAS) for Fire Assay Analysis, Portable Mineral Analyzer and Professional Lab Mineral Analyzer for XRF Test, and equipment for Gravity Separation Test such as Lab Jig Concentrator and Lab Concentrating Tables. Several other types of equipment including Lab Induced Roll Lift Magnetic Separator, Lab Isodynamic Magnetic Separator, Lab High Tension Separator, Sampling Pulverizer, Sieve & Shakers, Bench Drill Machine and High Voltage Rectifier are part of the range of DOVE laboratory equipment.
DOVEsupplies advanced and highly accurate range ofMetal Detectors. It is designed for ease of operation in highly mineralized soil condition. It provides a practical solution during exploration and prospecting different terrain with ease and dependability. DOVE Metal Detectors are designed for various depths and conditions.
DOVE provides a complete range of minerals assay testing services, for both alluvial (placer) and hard rock (primary) deposits. DOVE mineral assay services include Gravity Separation, Fire Assay Analysis and XRF Analysis for identification of gold, platinum, other metals and minerals concentration and simultaneously analyze up to 32 other elements, metals and minerals.
Reliable assay and minerals testing of your mine samples can lead you to the most efficient and best equipment configuration and plant design for the highest recovery of production and return of investment.