Hello, my partner! Let's explore the mining machine together!

[email protected]

mineral flotation machines small mining

flotation machines | mineral processing machine & solutions - jxsc

flotation machines | mineral processing machine & solutions - jxsc

Flotation is the most widely used beneficiation method for fine materials, and almost all ores can be separated by flotation. Another important application is to reduce ash in fine coal and to remove fine pyrite from coal. The flotation machine is mechanical equipment for realizing the froth flotation process and separating target minerals from ore. At present nearly 2 billion tons of ore in the world are treated by the froth flotation process. According to rough statistics, about 90% of non-ferrous minerals are recovered by the flotation method, accounting for 50% proportion in the field of ferrous metal mineral separation.

Suitable material Sulfide minerals, oxide minerals, non-metallic minerals, silicate minerals, nonmetallic salt minerals, soluble salt minerals, rare earth minerals, etc., including gold, silver, copper, lead, zinc, galena, zinc blende, chalcopyrite, pyroxene, molybdenite, nickel pyrite, malachite, cerussite, smithsonite, hematite, cassiterite, wolframite, Ilmenite, beryl, spodumene, brimstone, graphite, diamond, quartz, mica, feldspar, fluorite, apatite, barite, and so on.

The flotation machine is composed of single or multiple flotation cells, by agitating and inflating the chemical reagent treated slurry, some mineral ore particles are adhered to the foam and float up, and then be scraped out, while the rest remains in the slurry.

Industrial flotation machines can be divided into 5 classes, mechanical agitation flotation machine, pneumatic flotation machines, flotation column, airlift flotation machine, froth separation flotation machines. At present, the mechanical flotation machine is the most commonly used in industry, followed by the column flotation which has recently set off hot spot, the pneumatic type and froth separation are not common.

Commonly used flotation models TankCell series, Wemco series, Agitair series, SuperCells, RCS(reactor cell system), Denver laboratory flotation, KYF, and XCF series flotation devices, laboratory flotation machine. Well-known flotation machine manufacturers have Outotec, Flsmidth, Metso, BGRIMM, JXSC flotation machine china; column flotation manufacturers or models have Jameson, CPT, Counter-flow inflatable flotation column.

Main parts: slurry tank, agitator device, mineralized froth discharging system, electromotor, etc. 1. Slurry tank: mainly consist of a slurry inlet, slurry tank and a gate device for controlling the slurry volume, welded with steel plate. 2. Agitator: slurry tank have a series of the mechanically driven impeller that disperses the air into the agitated pulp. 3. Mineralized forth discharging: the useful minerals are enriched in the foam, scraped out, dehydrated, and dried into concentrate products.

Whatever flotation machines design is selected, it must accomplish a series of complicated industrial requirements. 1. Good mixing function. a qualified flotation machine should mix the slurry uniformly and maintain the particles especially the target mineral particle in suspension with the pulp, maximum the froth-mineral probability. 2. Adequate ventilation and distribution of fine bubbles. Except for the flotation machine performance, the frother type and dosage also matter to the distribution of the bubbles. 3. Appropriate agitation control in the froth beds. It is should pay importance to keep froth zones smoothly, which ensures the suspension of collector coated particle.

1. The throughput capabilities of various cell designs will vary with the ore property (beneficiability, size, density, grade, pulp, PH, etc.). In the case of ore easy separated, and a small amount of air inflation required, may choose a mechanical flotation machine; if the minerals with coarse size, proper to choose the KYF, BS-F, ore CLF type; what's more, when in case of ore easy separated, fine particles, high grade, low PH, flotation column is the best, especially in the concentrating process. 2. There is a difference between the process of concentrating, rough selecting. Thin froth layer is better for separate mineral particles, thus may not choose a large air inflation flotation machine.

Mining Equipment Manufacturers, Our Main Products: Gold Trommel, Gold Wash Plant, Dense Media Separation System, CIP, CIL, Ball Mill, Trommel Scrubber, Shaker Table, Jig Concentrator, Spiral Separator, Slurry Pump, Trommel Screen.

mineral flotation

mineral flotation

Stawell gold mine in co-operation with Outotec Services completed a flotation circuit upgrade on time and on budget last year that, instead of the projected 3.5% improvement, resulted in an increase of 4.5% since the project was completed. Payback was also impressive, occurring within less than four months.

Flotation has been at the heart of the mineral processing industry for over 100 years, addressing the sulphide problem of the early 1900s, and continues to provide one of the most important tools in mineral separation today. The realisation of the effect of a minerals hydrophobicity on flotation all those years ago has allowed us to treat oxides, sulphides and carbonates, coals and industrial minerals economically, and will continue to do so in the future.

There have been a number of important changes in the industry over the years as flotation technology and equipment have advanced. Xstrata Technology considers the most noticeable has been the increase in sizes of the flotation machines, from the multiple small square cells that were initially used, to the 300 m round cells used today that are the norm in large scale plants.

Other changes have been more subtle, but equally as important. One of these has been the design of the flotation circuit to make the most of the liberation and surface chemistry effects of the minerals. In a lot of these situations it is not a matter of bigger is better, that will make the process work, but being smarter in the application of flotation technology.

Xstrata Technology is one company that believes the smarter use of flotation machines can deliver big improvements in plant performance. Through its use of the naturally aspirated Jameson Cell, Xstrata Technology has been making inroads into the processing of more complex ores. Having a small footprint, and using the high intensity mixing environment of slurry and naturally induced air in a simple downcomer, the Jameson Cell provides an ideal environment for the separation of hydrophobic particles and gangue, it says. The small footprint of the cells also makes them ideal to retrofit into a circuit especially where space is tight.

While the cell has been included in some flotation applications as the only flotation technology such as coal and SX-EW, the main applications in base metals have seen the cell operating in conjunction with conventional cells. The combination of the two technologies enables the Jameson Cell to target the quicker floating material, while the conventional cells target the slower floating material. Such a combination provides a superior overall grade recovery response for the whole circuit, than just one technology type on its own, Xstrata Technology says. Below are some of the duties for which the Jameson Cell can be used.

Jameson Cells in a scalping operation target fast floating liberated minerals, and produce a final grade concentrate from them. The wash water added to the Jameson Cell assists in obtaining the required concentrate grade due to washing out the entrained gangue. Scalping can be done at the head of the cleaner (also known as pre cleaning), or at the head of the rougher (also known as pre roughing), and minimises the downstream flotation capacity using conventional cells needed to recover the slower floating minerals.

Sometimes deleterious elements found in the orebody are naturally highly hydrophobic, and need to be removed at the start of flotation, otherwise they will report with the valuable minerals to the concentrate and effect concentrate grade. Mineral species such as talc, carbon and carbon associated minerals, such as carbonaceous pyrite, can all be difficult to depress in a flotation circuit. On the other hand, floating them off in a prefloat circuit before the rougher is an easier way to handle them. Jameson Cells acting as a prefloat cell at the head of a rougher circuit, or treating the hydrophobic gangue as a prefloat rougher cleaner, is an ideal way to produce a throw away product before flotation of the valuable minerals, minimising reagent use and circulating loads.

Jameson Cells can be used in cleaning circuits to produce consistent final grade concentrates. The ability of the cell to keep a constant pulp level, even with up stream disturbances or loss of feed, enables a constant grade to be obtained.

Xstrata Technology concludes: Importantly in a lot of these circuits, it is not the selection of one type of technology that produces therequired grade and recovery, but the selection of several technologies to get the best results. The interaction of slow floating and fast floating minerals, entrainment, hydrophobic gangue and a myriad of other variables make it rare for just one type of technology to prevail, but the combination of different flotation machines can achieve the required outcome more efficiently, as well as make the circuit robust enough to handle variations in feed quality.

Clariant Mining Solutions service engineers develop custom formulated reagents for each ore to be processed, while collectors and frothers are carefully selected for mutual compatibility. Clariant is investing considerably in mining chemicals and in support services for its customers all over the world.

The Jameson Cell has benefitted from over 20 years of continuous development. Early this year, the 300th cell was sold into Capcoals Lake Lindsay coal operation in the Bowen Basin of Australia. Around this time there were a number of coal projects taking in new Jameson Cells, including expansion projects for Wesfarmers Curragh and Gloucester Coals Stratford operations (both in Australia), Riversdales Benga project in Mozambique and Energy Resources Ukhaa Khudag coking coal project in Mongolia.

Le Huynh, Jameson Cell Manager, said the interest for coal preparation plants has remained strong, where operators needed dependable and reliable technology to treat fine coal, an important source of revenue. During 2010, the Jameson Cell business also found success in other applications, including recovering organic from a copper raffinate stream at Xstrata-Anglo Americans Collahuasi copper SX-EW plant in Chile.

Le said the consistent generation of very fine bubbles and the high intensity mixing in the Jameson Cell, was ideal for recovering very low concentrations of organic from raffinate streams, typically less than several hundred ppm. High throughput in a small footprint, simple operation and extremely low maintenance due to no moving parts in the cell are distinct advantages in this application.

The cell is designed with features specific to suit such hydrometallurgy applications including specialist materials, a flat-bottomed flotation tank with integrated pump box and tailings recycle system, and large downcomers. The Collahuasi cell was the first of its type in Chile, though there are many other large cells installed in SX-EW plants in Mexico, USA and Australia to treat both raffinate and electrolyte streams.

Dominic Fragomeni, Manager Process Mineralogy, Xstrata Process Support (XPS), notes that accurate, rapid development of a milling and flotation flowsheet for a new orebody is key to successful mine development. Time honoured conventional practice has typically favoured the extraction of a bulk sample of up to several hundred tonnes for conventional pilot plant campaigns which could operate at several hundred kilograms per hour. Where sample extraction is limited, much reliance has been placed on locked cycle tests alone to produce design basis criteria. These approaches can be lengthy, expensive, carry scale up risk, and have seen a wide range of successes and failures at commissioning and during life of a mine.

XPS has miniaturised the pilot plant process. At the same time, it has improved the representativeness of results from the pilot plant campaign by using exploration drill core to formulate the pilot plant sample. This Flotation Mini Pilot Plant (MPP) was developed in collaboration with Eriez subsidiary Canadian Processing Technologies (CPT) and operates in fully continuous mode either around the clock or can be made to demonstrate unit operations on a shift basis. The feed samples are in the range of 0.5-5 t and can consist of exploration NQ drill core which improves the sample representativeness. The MPP operates in the range of 7-20 kg/h, an order of magnitude lower in sample mass and typically at a lower cost when compared to conventional pilot plants.

XPS has developed and validated a representative sampling strategy, an appropriate quality control model for metallurgical results and has accurately demonstrated operations results using Raglan and Strathcona ores and flowsheets. These validation campaigns, in scale down mode from the full scale plants, have produced actual mill recoveries to within 0.5% at the same concentrate grade with internal material balance consistent with the plant.

When designing a plant to recover copper, Scott Kay, Process Engineer with METS suggests (in METS Gazette, issue 32, October 2011) it would be prudent to perform some mineralogical analysis test work such as QEMSCAN (Quantitative Evaluation of Mineral by Scanning electron microscopy) to provide some knowledge on the proportion of sulphide and oxide minerals present, the grain sizes of each mineral and a suggested grind size before jumping into the bulk of the beneficiation test work.

Ideally, the characteristics of the copper bearing minerals should suggest an appropriate grinding circuit P80 of between 100 and 200 m (0.1 and 0.2 mm), which can be controlled by cyclones, or in some cases fine screens.

The Delkor BQR flotation machine (formally Bateman BQR) here at Messina Mowana Copper mine in Botswana. 15 x 50BQR and 16 x 200BQR flotation cells for Copper roughing, cleaning & re-cleaning. Oxide / Sulphide

Flotation reagent selection is paramount and test work is necessary to ensure the optimum reagent suite is utilised. If the ore contains a low amount of iron sulphides, xanthate collectors are often suitable to float copper sulphideminerals. If native gold is present, dithiophosphates can be used which are less selective to iron sulphides. Increasing and controlling the pH within the flotation vessel to between 10 and 12 causes the process to become more selective, away from iron sulphide gangue minerals such as pyrite to produce a cleaner copper mineral concentrate. Depending on the ore mineralogy, activators and depressants may be required to achieve the optimum reagent suite.

Recovery of copper oxide minerals can be achieved with flotation by sulphidising the ore. In essence, this creates a thin layer of copper sulphide (chalcocite) on the oxide grains which can then be activated and collected in the froth. When employed, this occurs after the sulphide flotation stage, however, this is not commonly used as other beneficiation processes, such as leaching and SX-EW are often more cost effective for copper oxide minerals.

A common flotation circuit usually includes a rougher/scavenger and a cleaner stage. As most copper orebodies exhibit an in-situ grade of less than 1% Cu, the mass pull to the rougher froth is often low. This means that the throughput of the cleaner stage is significantly less than the throughput of the rougher stage which imparts a relatively low capital and operating cost to the flotation circuit.

To counteract the possible absence of a scavenger stage, a slightly higher mass pull to the rougher froth is targeted (although still low overall) to increase overall copper recovery. The rougher froth can then be reground to increase the liberation of the copper sulphides from the iron sulphides before being fed to the cleaner flotation vessels. This results in a significant upgrade in copper in the cleaner froth whilst still achieving a high copper recovery. The final flotation concentrate usually contains between 25 and 40% Cu.

Alain Kabemba, Flotation Process Specialist at Delkor notes the major trend to treating lower-grade and more finely disseminated ores and lately the re-treatment of tailings. He also points to the broad applicability of size to below 10 m.

Real systems do not fulfil ideal conditions, mainly because of feed variation or disturbances. Before considering disturbances to flotation specifically, Kabemba says it is important to emphasise the interlock between grinding and flotation, not only with respect to particle size effects, but equally to flotation feed rate variations. The grinding circuit is usually designed to produce the optimum size distribution established in testing and given in the design criteria. When the product size alters from this optimum, control requires either changing feed tonnage to the circuit or changing product volume, with either causing changes in flotation feed rates.

While grindability changes due to the variation in ore properties are disturbances to the grinding circuit, they generate feed rate changes as disturbances to the flotation circuit. The variations in ore properties which affect flotation from those assumed in the design criteria must therefore necessarily include grindability changes.

This reflects important differences in flotation machine characteristics between the two processes. Grinding circuits are built and designed with fixed total mill volumes and energy input, so the grinding intensity is not a controllable variable, instead grinding retention time is changed by variation of feed rates. In contrast, the flotation circuit is provided both with adjustable froth and pulp volume for variation of flotation intensity by aeration rate or hydrodynamic adjustment. Reagent levels and dosages provide a further means for intensity control.

One recent trend has been towards larger, metallurgical efficient and more cost effective machines. These depart from the simpler tank/mechanism combination towards design which segregates and directs flow and towards providing an external air supply for types which had been self aerating and towards the application of hydrodynamic principles to cell design, like the Delkor BQR range of flotation machines, initially the Bateman BQR Float Cells.

Bateman has steadily developed the BQR flotation cells which have been in application for the past 30 years, and with its acquisition of Delkor in 2008, decided to rebrand the equipment into the Delkor equipment range. Kabemba explains that BQR cell capacities range from 0.5 to 150 m3 currently installed, and can be used in any application as roughers, scavengers and in cleaning and re-cleaning circuits.

Provide good contact between solid particles and air bubbles Maintain a stable froth/pulp interface Adequately suspend the solid particles in the slurry Provide sufficient froth removal capacity Provide adequate retention time to allow the desired recovery of valuable constituent.

Highest possible effective volume and reduced the froth travel distance Improved metallurgical performances in terms of grade recovery and reduced capital and operating costs based on reduced fabrication material and ease of maintenance

Kabemba says there are not many differences in terms of design between BQR Flotation cells; however, from the BQR1000 upwards, the flotation cells have internal launders to maintain the design objectives and benefits highlighted.

Operating variables, such as impeller speed, air rate, pulp and froth depths have to be adjustable over a sufficient range to provide optimum results with a given ore, grind and chemical treatment, but adjustment should not extend beyond the hydrodynamic regime in which good flotation is possible.

The largest current BQR flotation machine is shown in the table. In the near future the BQR2000 (200 m3) and BQR3000 (300 m3) will be available to the market. Kabemba also explained that circular cells reduce the amount of dead volume when compared to square cells. This enables a much higher effective pulp volume, hence increasing the effective energy input into the flotation cell. In addition tank type cells offer enhanced froth removal due to the uniform shape of the circular launders. He concluded that fully automated flotation cells are becoming more and more common with the aid of smart control and advances in software in the marketplace.

FLSmidths flotation team notes that fundamental flotation models suggest that a relationship exists between fine particle recovery and turbulent dissipation energy1. Conversely, increased turbulence in the rotorstator region is theoretically related to higher detachment rates of the coarser size range2. Conceptually, the suggested modes of recovery for the extreme size distribution regions appear to be diametrically opposed.

Industrial applications have previously confirmed that imparting greater power to flotation slurries yields significant improvements in fine particle recovery. However, recovery of the coarser size class favours an opposing approach, the FLSmidthteam believe. An improvement in the kinetics of the fine and coarse size classes, provided there is no adverse metallurgical influence on the intermediate size ranges, is obviously beneficial to the overall recovery response. Managing the local energy dissipation, and hence the power imparted to the slurry, offers the benefit of targeting the particle size ranges exhibiting slower kinetics.

New concept, Hybrid Energy FlotationTM (HEFTM),was recently introduced by FLSmidth. In principle it decouples regimes where fine and coarse particles are preferentially floated. HEF includes three sections:

This subject will be expanded upon at the 5th International Flotation Conference (Flotation 11) in Cape Town, South Africa. The fundamental parameters that influence fine and coarse particle recovery will be reviewed. The potential dual recovery benefit is then presented in terms of its practical implementation in a scavenging application. HEF is proposed as the preferred methodology of recovering these slow-floating size ranges; a method that opposes the traditional approach of residence time compensation.

StackCell offers column-like performance in a substantially smaller footprint than conventional cells. These compact, stackable units provide considerable savings for new installations and are ideal for expanding capacity in an existing plant

Eriez Flotation Group introduced the StackCell flotation concept in 2009. This innovative technology recovers fine particles more efficiently than mechanical flotation cells. Weve taken the inherent advantages of mechanical flotation and adapted them to a new design that is significantly smaller and requires less energy, explained Eriez Vice President Mike Mankosa. We focused on reducing the retention time and energy consumption by implementing a completely different approach to the flotation process. This new approach provides all the performance advantages of column flotation while greatly reducing capital, installation and operation costs.

At the core of the StackCell technology is a proprietary feed aeration system that concentrates the energy used to generate bubbles and provides bubble/particle contacting in a relatively small volume. An impeller in the aeration chamber located in the centre of the cell shears the air into extremely fine bubbles in the presence of feed slurry, thereby promoting bubble/particle contact. Unlike conventional, mechanically agitated flotation cells, the energy imparted to the slurry is used solely to generate bubbles rather than to maintain particles in suspension. This leads to reduced mixing in the cell and shorter residence time requirements.

The StackCell sparging system operates with low pressure, energy efficient blowers that decrease power consumption by 50% compared to air compressors or multi-stage blowers used in other flotation devices.

The low-profile StackCell design features an adjustable water system for froth washing and also takes advantage of a cell-to-cell configuration to minimise short-circuiting and improve recovery rates. Space requirements for the StackCell design are approximately half of equivalent column circuits, with corresponding reductions in weight leading to reductions in installation costs. Units can be shipped fully assembled and lifted into place without the need for field fabrication.

This technology can provide recoveries and product qualities comparable to column flotation systems while using a low profile design. Not intended to replace the need forcolumn flotation, it does provide an alternative method to column-like performance where space and/or capital is limited. The small size and low weight of the new StackCell makes possible lower cost upgrades where a single cell or series of cells may be placed into a currently overloaded flotation circuit with minimal retrofit costs.

Steve Flatman, General Manager of Maelgwyn Mineral Services (MMS) also comments on the trend of moving towards a finer grind to improve mineral liberation. Unfortunately conventional tank flotation cells are relatively inefficient in recovering these metal fines below 30 m and very inefficient at the ultra fine grind sizes below 15 m. The incorporation of regrind mills on rougher concentrates has further exacerbated this problem. To date the conventional flotation tank cell manufacturers have attempted to counter this fall off in recovery of fine particles by inputting increasing amounts of energy (bigger agitation motors) into the system to improve bubble particle contact. Unfortunately this tends to compromise coarse particle recovery.

He says the solution is MMSs Imhoflot pneumatic flotation technology and specifically the Imhoflot G-Cell. Recent pilot plant test work at a nickel operation with a three stage Imhoflot G-Cell pilot plant enabled an additional 30% nickel to be recovered from the conventional flotation tank cell final plant tails. The recovery was predominantly associated with the minus-11 m fraction indicating that this improved recovery was not just related to additional residence time. The above results are in line with an earlier pilot plant trial using G-Cells on a zinc operation where an additional 10-20% zinc was recovered from cleaner tailings this time being associated with minus 7 m material.

It is postulated that the above improvements are related to the order of magnitude increase in terms of air rate (m/min/m pulp)for the G-Cells due to their principle of operation where forced bubble particle contact takes place in the aeration chamber rather than the cell itself with the cell merely acting as a froth separation chamber. Typically in percentage terms the G-Cell air rates are five to ten times that of conventional flotation although the overall or total air usage is approximately half.

When this additional targeted energy input is combined with the centrifugal action of the GCell and small bubbles benefits are obtained in both the flotation rate (kinetics) and overall recovery. The improved kinetics results in a much lower residence time than conventional flotation facilitating a double benefit of both reduced footprint and improved recovery.

Metso notes a main drawback of column cells being low recovery performance, typically resulting in bigger circulating loads. Its CISA sparger is derived from the patented MicrocelTM technology and enhances metallurgical performance by allowing flexibility on the graderecovery curve. Metso Cisa says the main advantages of its column technology include:

At the bottom of the column, the sparger system raises mineral recovery by increased carrying capacity due to finer bubble sizes. This maximises the bubble surface area flux which is a standard parameter in evaluating flotation device performance. It also provides maximum particle-bubble contacts within the static mixers and effective reagent activation from the mechanical operation of the pump.

It is well known that coarse particles behave poorly in a conventional flotation cell and were previously regarded as non-floatable. However, recent laboratory work demonstrates that Fluidised Bed Froth (FBF) flotation extends the upper size limit of flotation recovery by a factor of 2-3 resulting in significant concentrator performance benefits. AMIRAs P1047 project, Improved Coarse Particle Recovery by FBF Flotation, is expected to commence in 2012, and will be structured in two phases.

Early rejection of gangue with minimum mineral loss. Potential for significant increase in concentrator throughput or significant improvement in capital efficiency Reduced energy consumption. Independent modelling predicts that if particles of 1 mm can be floated, comminution energy consumption will be lowered by at least 20%. Better management of water requirement. FBF cells can take product straight from the milling circuit without dilution, and the feed to the FBF cell could be up to 80% w/w solids, which could lead to significant savings in process water demand. Improve recovery of metallic and other dense minerals. In a continuous FBF Cell, dense mineral particles will tend to sink to the bottom and accumulate in the cell, thus they can be recovered in a concentrated form by emptying the cell periodically. This could be a significant benefit where the concentration of the heavy metallic material is too low to warrant a separate treatment plant to recover them.

In Australia, Northgate Minerals Stawell gold mine recently completed a project through which it aimed to increase recoveries by 3.5% by upgrading the flotation plant. This upgrade was implemented after Stawell changed its production profile to process lower grade ore at higher throughput rates.

Instead of the projected 3.5% improvement, the upgrade from Outotec Services has resulted in an increase of 4.5% since the project was completed on time and on budget last year, despite the wettest seasonal weather in recorded history. Payback was also impressive, occurring within less than four months. The projected payback was 5.5 months, so it was a pleasant surprise when it happened so soon explains Jodie Hendy, senior metallurgist at Stawell.

The project has also achieved payback in less than four months and has delivered further ongoing benefits, including easier operation and reduced maintenance costs, says Outotec Services, which worked in close partnership with Stawell Gold to ensure the site remained fully operational during

The mine, which has produced more than 2 Moz in its 26-year history, previously employed a flotation circuit consisting of a bank of eight mechanical trough cells in the rougher circuit, followed by two banks of 2 x OK3 Outotec cells as cleaners. The feed rate to the cells was between 90-105 t/h, at 50-55% solids. The overall flotation circuit was not performing at optimal rate due to entrainment problems in the rougher cells when feed density increased from 45% to 55% solids, typically at 105 t/h.

In anticipation of future production levels and as part of Stawells focus on operational excellence, it was decided to upgrade the flotation circuit. Following a site audit from Outotec Services, a 2 x TankCell -20 configuration equipped with larger TankCell -30 mechanisms was proposed to help optimise flotation. The larger mechanisms would allow operation at very high percent solids (50% and over).

The TankCell design also allows a much deeper froth depth and better concentrate grade through optimised launder lip length and surface area. These cells known for great performance, ease of operation and reduced power and air consumption. Outotec Services was commissioned to handle the complete turnkey solution of the new rougher circuit, including design, supply, installation and commissioning.

The schedule was demanding but achievable, in just 30 weeks. It was decided to adopt the partnering approach between Stawell and Outotec Services, because this collaborative method ensured open communication, with all parties having greater ownership of the project and its aims. This close teamwork resulted in meticulous planning and site remaining fully operational at all times. Pipework and electrical easement ducts, for example, were rerouted early in the project. Tie-in points for new cells and rerouting of pipework were also planned upfront in the project and all disruptive work was completed during shutdowns.

The project overcame a number of challenges, including an extremely limited footprint, which was adjacent to a gabion wall, close to the runof-mine pad and also close to a reagents shed, which could not be moved. Additionally, existing process requirements at Stawell required specific elevations for the new TankCells. Structural stability was the main issue when designing the tank support structure due to the height of the tanks and the limited footprint. Sufficient stiffness was required such that the operation frequencies of the TankCells would not interfere with the natural frequency of the tank support structure. Through FE modelling of the structure, section sizes and bracing orientations were optimised to produce the required stiffness.

Despite the challenges, the turnkey installation of the new rougher circuit, along with blowers for the complete flotation circuit, was completed within deadlines. Because all tie-in points had been already carefully planned upfront, commissioning was a seamless exercise.

Designed to cope with projected increases in production and considerably more operator friendly than its predecessor, the new TankCell 20 cells have quickly proved their worth at site. The air demand for the old rougher cells, for example, was estimated at over 3,000 Am3/h, whereas the estimated air demand on the Outotec TankCells is a maximum of 992 Am3/h.

The Outotec FloatForce rotor-stator mechanism, with its unique design, delivers enhanced flotation cell hydrodynamics and improved wear life and maintenance. Maintenance on the Outotec TankCells has also been minimal since the upgrade, Hendy commented. Basically we check the cells during shutdowns but there has been no maintenance required in the nine months since commissioning. The TankCells have really delivered on their reputation. Basically, they do exactly what they are supposed to do.

Turning to flotation reagents, Frank Cappuccitti, President of Flottec explains that Flottec and Cidra are working very hard jointly on developing instruments that will measure hydrodynamics in the flotation cell and circuit in a bid for better flotation control. This would be a great step forward in using a combination of reagents and sensors to optimise flotation systems. It brings together the knowledge we have developed in both how reagents effect hydrodynamics and measuring the hydrodynamics to maintain optimum conditions. He explains that back in the 1990s, when he worked at a well-known mining chemicals supplier, we spent most of our research on trying to find the best collectors. The thinking was that we could try to develop collectors with absolute specificity. In other words, we could develop a collector that would float only specific minerals and provide clients with an almost perfect flotation separation. This was our approach to flotation optimisation. Unfortunately, we discovered that there was no such thing as absolute specificity. In fact, we had trouble measuring any improvements in the circuits because they were multi-variant and highly complex. Every change made was always a trade off between grade, recovery and cost. Changing one thing in the circuit seemed to improve something but always got a negative response in some other variable. It was also very hard to measure the performance of the flotation circuit because the only real parameters you could measure on line were concentrate grades and tails of the circuits, which were always after the fact. There was little ability and understanding about what real time measurements we could take other than air rates, cell levels and flow rates. So even if we got an improvement or a response to a change, we never knew if that was a response to a change or a natural variation in the system. Every test needed long term statistical trials to get some confidence in any real change.

So, I wrote a paper in the 1990s that basically said that until we could measure the real time variables in a flotation system and learned to really understand and control the system, we were limited in our ability to work on continuous improvement in reagent optimisation. We needed new sensors that could measure the performance of the flotation circuit so we could learn to control it. Once we got this, then we could actually measure improvements and use this to develop reagents.

Fortunately, with the advent of strong computing power and software, we have moved forward tremendously in the last decade in understanding the flotation circuit. Froth cameras that tried to measure froth grade and velocity were one of the first new sensors developed to assist in optimising circuits. Through the work of universities such as McGill and organisations like JKtech, new sensors have been developed that could actually measure reliably and in real time the hydrodynamic parameters in the flotation cell. Flotation cell hydrodynamics (gas dispersion parameters) is critical to the performance of the cell. When we talk about these parameters, we are talking about measuring what is happening in a flotation cell. Flotation is really about making bubbles and using the surface area of the bubble to do the work of transporting hydrophobic minerals to the froth. In flotation cells, we add air, create bubbles of a certain size and speed that provide the surface area to do the flotation. The more bubbles and the smaller the bubble, the more surface area we have to do the work. This surface area we create is known as the surface bubble flux (Sb) and controls the kinetics of flotation. Now that we have instruments that can measure the air into a cell (known as Jg), measure the size of the bubble diameter (Db) and the gas hold up (Eg), we can figure out how the relationship between these parameters and how they affect the Sb and flotation circuit performance. We can also now do research on how reagents can be used to control these parameters as well.

Research of the last few years has shown that frothers actually play a much more important role in flotation hydrodynamics than once thought. Frothers perform two major functions. They create and maintain small bubbles in the pulp to transport the minerals and they create the froth on top of the cell to hold the minerals until they can be recovered. The froth is created because frothers allow a film of water to form on the bubbles which makes them stable enough not to break when they reach the surface of the cell. Fortunately, the water drains over a short period of time and the froth will eventually break down. Froth breakdown is essential for cleaning and transporting the concentrates. Small bubbles are essential in making flotation efficient. For the same volume of air in a cell, smaller bubbles give much higher surface area, which in turn gives much higher kinetics.

We now know that as you increase the concentration of frothers to the cell, the bubble size gets smaller, and the film of water on the bubble gets bigger. But bubble size does not keep getting smaller forever. The frother will reduce the bubble down to a certain size, which is about the same for all frothers in the same set of conditions. The concentration of frother where the bubble is at a minimum is known as the critical coalescence concentration or CCC.

Each frother has a different CCC. Each frother also has a different ability to add water to the bubble and hence provides different froth stability. This also changes with concentration. We have learned in the last few years that each frother has a hydrodynamic curve which relates the bubble size with the froth stability. Strong frothers give very high froth stability at the CCC, while weak frothers give very low stability of the froth at the CCC.

This new understanding of how frothers affect flotation cell hydrodynamics has lead to new methodologies to optimise flotation circuits. Flottec has worked on an optimisation system where a frother is added to a circuit at the CCC (which guarantees maximum kinetics or maximum Sb) and the performance is measured. Then frothers of different strength are added (always at the CCC) until the right strength for maximum performance is determined. Adding the frother at the CCC is the critical optimisation difference. By doing this you are always guaranteed to have maximum kinetics. If the frother used is too strong, the dosage will have to be cut back below the CCC or the froth will be too persistent. This lowers flotation kinetics. If the frother is too weak, too much has to be added to get the froth strength and this increases cost and likely reduces recovery. Flottec has been conducting research withMcGill University to develop the hydrodynamic curves and CCC for all families of frothers in order to implement the new methodology of frother optimisation in plants.

The next step in this research is to be able to use new sensor technology to measure and control the flotation system by controlling the hydrodynamics in the cell. With our current knowledge of how air rate, cell levels, and frother addition affect bubble size, water recovery and gas hold up, we can use these control variables to maintain the optimum hydrodynamics in the cell resulting in the optimum flotation circuit performance. Flottec is working with companies like Cidra to develop new sensors that can provide real time information on cell hydrodynamics (gas dispersion parameters) and on froth stability properties in order for us to optimise the reagents and operating strategies used in a plant. This will bring flotation performance to the next level.

Clariant Mining Solutions business is investing considerably in mining chemicals. It has opened a new laboratory at its US headquarters in Houston, Texas, dedicated to the development and optimisation of chemical solutions for North American customers. The laboratory is part of a planned multi-million dollar investment into Clariants global Mining Solutions business, which includes establishing several new Mining Solutions laboratories around the world. This network is intended to enable the business to better support customer needs and address regional challenges. Most recently, Clariant has opened new mining labs in South Africa (Johannesburg) and in China (Guangzhou). The new laboratories will complement existing facilities in Europe and Latin America.

As part of Clariant Mining Solutions global investment, new mining labs have been established in South Africa and China, to complement those already operating in Brazil, Chile, Peru, Australia, North America, Russia and Germany

Mining is a strategic focus area for Clariant, said Christopher Oversby, Global Head of Clariants Oil & Mining Services business unit. This investment further demonstrates Clariants ongoing commitment to providing innovative technologies and solutions for our mining customers around the world.

The Houston laboratory will process ore samples from customers in the USA and Canada. These samples were previously handled in Clariants mining laboratories located in South America and at the companys global research facility in Frankfurt, Germany. We are very excited about the new mining laboratory and the opportunity it provides us for offering our North American mineral processing customers even more localised services and attention, said Paul Gould, Global Head of Marketing and Application Development for Clariant Mining Solutions. The Houston lab will allow Clariant technicians to more efficiently develop optimised reagent solutions for our US and Canadian customers.

Additionally, Clariant is in the process of developing a new Innovation Center in Frankfurt at a cost of 50 million. Employing nearly 500 people and covering 30,000 m2, the facility will focus on customers using an integrated multidisciplinary approach to problem solving. Clariant says an open innovation approach on joint ventures with external partners will ensure the acceleration of the idea-to-market process. Mining research and development will also be part of this facility.

Axis House has been developing reagent technologies for the past 10 years, at its flotation laboratory in Cape Town, South Africa and more recently at it metallurgical labs in Sydney and Melbourne. These were acquired when Axis House bought the oxide flotation reagent technology from Ausmelt Chemicals. A practical application technology strategy was followed with Axis House providing a complimentary suite selection and optimisation service to its clients, who were then mainly interested in the Axis developed technology of combining fatty acids, hydroxamates and sulphidisation suites to effectively and economically float oxide minerals.

Early on the focus was on developing reagents to float complex ores which contained multiple minerals with varying flotation kinetics. Often the limiting factor was not only the sluggish flotation kinetics of the minerals but the process plants own equipment limitations, like flotation and conditioning times. Developing a reagent that floated a certain mineral was simply not enough. The solution was to develop suites of reagents which could function synergistically. By altering the types of collectors and the dosages, the company could optimise both the use of the processing equipment and the collecting power. It says this approach has successfully been applied to various types of base metal oxide ores.

It is now taking this innovative approach into the field of rare earth element (REE) flotation. This fits into the Axis House business plan as the chemistries are quite similar to what is in existence at Axis already. Of course some tweaks will have to be made to the reagents as well as the laboratories this process has already started, with the first batch of REE test material having arrived at Cape Town, and new reagent samples at the ready. There are a large number of REE projects coming online in the next few years. Most of these orebodies have not been previously treated at industrial level and so will face difficulties when scaling up. REO (Rare Earth Oxides) are often difficult to float and the development of multiple collector systems for these ore types would help increase the viability of these projects.

Jerry Sullivan, Global Marketing Manager-Mineral Processing, Cytec Industries Inc, discussed collectors, which contain mineralselective functional groups. They have a hydrophobic hydrocarbon tail. Changing the molecules functional group changes the preference for what mineral it will adsorb on to. Changing the length of the hydrocarbon chain changes the hydrophobicity of the molecule. This is related to the strength of the collector.

Within the collector molecule, there are donor atoms whose goal is to form bonds with acceptor atoms within the ore. Nitrogen, oxygen, and sulphur are the most important donor atoms in all reagent chemistry. Sulphur is the most important donor in sulphide collectors. Nitrogen and oxygen are additional donor atoms. Phosphorous and carbon are central atoms carrying the donors. They only have indirect participation in interactions. He noted the general characteristics of sulphide collectors to be:

Ionic collectors are stronger and less selective Neutral, oily collectors are weaker, more selective Higher homologues (more carbons) are stronger than lower homologues (fewer carbons) Cytecs NCPs are very selective collectors

There is a strong case for formulated products (or blends), he continued That is because mineralogy is complex. Plant performance is also inherently variable. Mineralogy changes routinely. In addition, different minerals have different affinities for reagents. Various minerals will compete for a given reagent. Modifiers used will also influence reagent partitioning. Particle size distribution will also affect recoveries (recovery losses in coarse and fine size range). A single collector will not be sufficiently robust. Indeed, most plants use two or more collectors. The goal is to pick reagents that will get to the right minerals. Utilising a collector blend can balance cost and performance.

Cytec has multiple collectors and collector blends that are continuously being developed to tailor to the customers application. A few of the collector families that have recently been introduced to the market include the new XR Series Xanthate Replacement Collectors, developed to meet the desire to replace xanthates. This new series of collectors are cost competitive with xanthates and are strong collectors but with high selectivity. In addition, they are safer and vastly improves handling and level of toxic exposure of the personnel to product, stock safety management and simplifies plant operations.

The XD 5002 blends were developed to operate in a broad pH range 8-12 and be highly selective in Cu/Mo, Cu/Au sulphide ores, enhance Mo recovery in Cu/Mo bulk float and enhance Au recovery in Cu/Au ores. The MAXGOLDTM blends were introduced to float primary Au ores; auriferous pyrite, arsenopyrite, and tellurides and are also capable of enhancing recovery in Cu/Au ores.

It is now possible to use measurement devices based on impedance tomography to create realtime 3D images. The technology opens up entirely new possibilities in controlling flotation processes. With Flotation Watch the operator can see what takes place underneath the surface. Flotation Watch measures several parameters at the same time, on-line. The sensor can measure the stiffness of the froth, the thickness of the froth, analyse the interface area between the froth and the slurry and it can analyse the slurry too depending on the customer needs, says Jukka Hakola, Numcores Vice President of Sales and Marketing.

With Numcore measurement devices, the size and quantity of air bubbles and the solid matter content of the froth bed can be monitored by means of electric conductivity distribution. With Flotation Watch the stiffness of the flotation froth can be measured and this helps to keep the recovery in higher level. The signals for the production failures, such as hardening and collapse of the froth bed, can be seen beforehand and avoided. This way we can help to minimise the losses in the flotation process, says Hakola.

Real-time characteristics are a key in this technology; in other words, the system continuously provides the operator with factual data on what is happening in the flotation cells, for example the location of minerals and the bottom surface of the froth bed. Because it has not been possible to look inside tanks, controlling a mineral concentration process has largely been based on experience-derived knowhow. Now that operators can look inside the process, it is possible for them to maintain an optimal mix all the time, says Hakola.

Numcore has, in close co-operation with a few key customers, developed measurement technology to better serve everyday work. We have now delivered several Flotation Watch sensors to flotation cells in several markets and for different metals such as copper, zinc and gold. One of the main benefits is that contamination of the probe is taken into account in mathematical formula and the measurement probe does not need to be cleaned. Our sensor has been in a zinc rougher flotation cell for nine months and is giving accurate results to the operator. We can now offer automated control for flotation process with Flotation Watch and see that this can bring new benefits for our customers, he promises.

Numcores measurement technology is currently in test use at Inmets Pyhsalmi copper-zinc mine (IM, April 2010, pp10-18), among others. According to Seppo Lhteenmki, Processing Mill Manager, the system has provided accurate information on the condition of the froth bed, and the technology has functioned reliably. We have tested the device for a few months, and it has provided clear benefits for those operators who have received operator training for it and actively monitored the data provided by the system. The device appears to be so useful, in fact, that we are seriously considering buying it after the test period, he says.

Mettler Toledo notes that pH greatly determines the efficiency of the flotation, which minerals will float, or even if there will be any flotation at all. The critical pH value for efficient flotation depends on the mineral and the collector. Below this value the mineral will float, above it, it will not (or, in some cases, vice versa).

In a recent white paper www.mt.com/pro-phflotation, the company says in order to overcome difficulties with the hostile environment in flotation cells, sensor manufacturers are very creative in their choice of sensor design. It is possible to find pH electrodes with a ceramic, plastic, rubber or even a wood reference diaphragm. Still, their performance can be severely limited as the colloidal particles and sulphides interfere almost instantly with the reference system. The sensors maintenance requirement is therefore high, requiring very frequent cleaning and calibration, and usually sensor life is short.

Mettler Toledo has acknowledged this issue and to combat it has designed the InPro 4260i pH electrode with Xerolyt Extra solid polymer electrolyte. The InPro 4260i does not have a diaphragm and instead features an open junction, which is an opening that allows direct contact between the process medium and the electrolyte. Contrary to the miniscule capillaries of any other type of diaphragm in conventional pH electrodes, the diameter of the open junction is extremely large and much less susceptible to clogging or fouling. Another significant difference is in the choice of polymer electrolyte. Xerolyt Extra was designed specifically for service in tough environments to provide a strong and lasting barrier against sulphide poisoning.

The companys Intelligent Sensor Management (ISM) is a platform based on sensors with embedded digital technology for better pH management. The integrated system consists of a digital sensor and ISM-compatible transmitter. The key to the technology is a microprocessor which is contained within the sensor head and is powered by and read through the transmitter. Critical sensor information such as identification, calibration data, time in operation and process environment exposure are all recorded and used to continuously monitor the health of the sensor.

By constantly keeping track of process pH value, temperature and operating hours, ISM calculates when sensor calibration, cleaning or replacement will be needed. Any need for maintenance is recognised at an early stage.

In recent years, researchers at Imperial College have been focusing on measuring air recovery in industrial flotation cells and have found that a peak in metallurgical performance (improvements in both grade and recovery) corresponds well with a peak in air recovery. Major platinum and copper operations have already observed the benefits of using this methodology as developed by the researchers. JKTech is now licensed by Imperial Innovations to commercially provide this methodology and associated benefits to the global minerals industry.

The PAR technique comprises two stages evaluation and implementation. The evaluation stage involves determining the effect of the technology at a mine site, typically determining the peak air recovery for a bank (or banks) of flotation cells and evaluating the resultant metallurgical performance. The implementation stage involves setting the air rates to those that maximise the air and/or metal recovery, and support and training of site personnel including operating manuals. The implementation stage requires an end-user license to be obtained by the sites through Imperial Innovations.

GIW Industries has launched its new High Volume Froth (HVF) pump. Unlike any other pump on the market, GIW says, the HVF pump can pump froth without airlocks. It provides continuous operation without shutdown or operator intervention. The new hydraulic design actually removes air from the impeller eye while the pump is running, so you can keep

Designed for air-entrained slurries, the pump can be used in phosphate mining, hard rock mining and oil sands. The pump offers improved efficiency and is environmentally friendly and cost effective, GIW reports

The GIW HVF can be retrofit into many existing froth applications. The pumps deaeration system includes a patent-pending vented impeller and airlock venting. This helps to eliminate sump overflow due to pump airlock; reduce downtime; and allow water use to be restricted to the bare minimum. Fewer pumps are required for less capital expense, requiring less water and power usage.

The HVF pump has been fully tested on froth and viscous liquids. The pump exceeded expectations at a large phosphate company in Finland. The companys existing pumps were not able to provide the required flow and were airlocking at only one-third of process design capacity. After installing an HVF pump, the company achieved a flow of 415 m3/h.

Traditional slurry pumps are prone to airlock when working with slurries that incorporate froth. A pump works by pulling in a liquid at a certain pressure and adding mechanical force to expel the liquid at a higher pressure. The air in the froth does not want to move to a higherpressure zone, and it is prone to build up at the lower-pressure pump entrance. The accumulation of air can eventually block the pump entrance completely, leading to airlock, which requires pump shutdown or operator intervention to avoid sump overflow.

How is GIWs HVF pump different? The main innovation is in the impeller design. Typically, air bubbles gather at the centre of the impeller as the heavier fluids are spun to the outer edges. The HVF pumps de-aeration system includes the vented impeller and airlock venting. In the HVF pump, small holes in the centre of the impeller allow air bubbles to pass through to a separate port. The port vents air up and out of the pump to normal atmospheric pressure.

small flotation | xfdiii single cell lab flotation - jxsc machine

small flotation | xfdiii single cell lab flotation - jxsc machine

Introduce Small Flotation XFDIII Single cell Laboratory flotation machine is widely used in geology, metallurgy, building materials, chemicals and other research institutions and laboratories for mining stirring, scrub, separation, and selection of a small number of ore samples and so on. XFD floatation machine is Froth Flotation Equipment, uses inverter technology, variable speed impeller, digital display, and also change from the outside air to intake inflated with the precise adjusted, clear and stable display. According to user needs, FX Model Continuous Mechanical Flotation Machine can be equipped with a heater, temperature control device to control, display tank mine fluid temperature at any time. Small Flotation Machines can be equipped with additional water level automatically adjusts automatically administration and other devices can achieve a higher level of automation. The flotation machines have a frame member, spindle transmission parts, locking parts, wiper parts, flotation tanks, outside the inflatable devices and electrical control components. Gas of pump tank supply to the rotor agitation, and mix with ore fluid, the stator is cut to produce tiny bubbles mineralization. Rotor speed is stepless and can be adjusted by the inverter. Fixed flotation tank fasten by hand wheel drive screw clamp. Shaving foam body, its trajectory is a circular motion. click to know the Industrial flotation separation machine.

Working Principle of Small Single Cell FlotationSingle cell flotation machine is an important device to realize the flotation process with only one cell. Single groove flotation machine is suitable for the separation of colored ferrous metals, but also for non-metallic materials such as coal-sparkling stone, talc. The single groove flotation machine is driven by the motor triangle drive impeller rotation, resulting in centrifugal action to form negative pressure, on the one hand, adequate air and slurry mixing, on the one hand, mixing pulp and medicine, and at the same time refine the foam, Above the mineral-bonded foam, the mineral floats to the surface of the ore pulp to form mineralized foam. Adjust the height of the gate to control the liquid level so that the useful foam is scraped out of the scraper. The basic performance of single tank flotation machine requires good inflatable action, stirring effect, stable foam zone, continuous operation, and easy adjustment.

small flotation machines

small flotation machines

These ALL STAINLESS STEEL flotation machines are used to form banks of 2 cells. The can be arranged in series to accommodate small plants of up to 1 TPH (24 Ton/day). View the description below for a flotation cell capacity table you can use to estimate how many machines you need.

Look at the capacity you need in KPH (kilo/hour) or TPD (ton/day) and look for a number of machines, ideally, between 2 and 8. From this, select what cell size (volume) gives you that quantity of machines to form your flotation bank and circuit.

FX Model Continuous Mechanical Flotation Machine is applicable to separation of minerals with float-free method in labs. It is a unit of several combinations of two cells with number of the cell being even, varying from two to ten cells. Left or right type flotation machine can be supplied as required by customer.

To adjust the level of slurry in the cell and the thickness of the scraped froth layer, use wall plates of the two cells to make intermediary cell;install slurry level regulator; and mount orifice plate onto the cover in the cell to avoid negative effects on the froth zone exerted by the chaotic motion of slurry, as well as to avoid the gangue from being taken into the concentrate by the machine.

Lining plates are installed at the cell so that the bottom of the cell will not be abraded. The lining plate can be replaced. On the outside of the cell bottom is a discharge mouth, which is used to discharge water during its cleaning. The slurry flows through the overflow mouth of wall panel into the intermediary cell and tail cell. It flows to the lower part of the intermediary cell and the duct covered by the lower part of the cell wall and then to the next cell. In this way, it can continue to flow through all the cells of flotation machine. It flows from the feed cell and is discharged from the discharge mouth of the tail cell. The front and back of the lower part of the cell is installed feeding mouth, to make it easy to change the process flow.

The impeller system is a disk impeller which is installed in the center of the cell in the flotation machine and whose blades are radially arranged. It is fixed onto the lower end of the impeller shaft and revolves around the vertical shaft pipe.

The upper end of the pipe lies above the pulp stone and the froth layer while its lower end is supported on the cover. When the impeller rotates, a large amount of air can be sucked along the vertical pipe. Below the cover is fixed protective disk. The gap between the safety disk and the impeller depends on the amount of sucked air. It can not be larger than 3mm at most. When the gap is too large, replace the abraded protective disc and make appropriate adjustment.The holes in the vertical pipe are used to circulate slurry as well as mix the slurry and air. The rolling shaft installed inside the bearing shell above the impeller shaft rotates. The bearing shell is installed on the crossbeam and belt pulley is fixed on the top of the shaft which rotates through the V-belt when the motor is turned on. The tension of the V-belt is adjusted through the nuts.

The froth is scraped along the flotation machine through rotary scraper. The scraper is installed outside the discharge mouth of cell. At one end of the scraping shaft is installed belt pulley which rotates through the drive of worm reducer and V-belt.

flotation machines & flotation cells

flotation machines & flotation cells

In small plants, it is common practice to include conditioners following the last stage of grinding. Additional conditioners are normally required between flotation operations which produce individual mineral concentrates. Each conditioner stage should consist of a minimum of two separate agitated tanks. Provision must be made to drain and clean conditioner tanks to appropriate flowsheet locations. This is particularly important in the case of conditioners which follow the grinding circuit since these tanks tend to accumulate oversize material produced during grinding circuit upsets.

Conditioners provide positions in the plant flowsheet wherein changes to the ore slurry are brought about by the addition of reagents and pH modifiers. Conditioners must always be designed to provide adequate time for chemical or physical changes induced by reagent additions to proceed to completion. Conditioners also serve a useful function in that swings in ore grade, particle size distribution, or other flotation variable tend to be partially homogenized and dampened during the conditioning unit operation. For example, in small installations it is not unusual to experience wide swings in feed grade. The conditioning unit operation provides the operator an opportunity to modify reagent additions in order to maximize recovery during periods of process instability. If possible, conditioner tanks should be arranged in tiers so that slurry overflows between sequential tanks under the influence of gravity.

The selection of flotation cell size and configuration can have a substantial influence upon installed cost and can contribute to operational efficiency. Two possible flotation configurations for a 500 metric ton per day installation are presented in Figure 5. The computational basis assumes 30 percent solids in rougher flotation, 20 percent solids in cleaner, recleaner and cleaner-scavenger flotation, a ratio of concentration in rougher flotation of 3.07 an overall ratio of concentration of 5.0, and an ore specific gravity of 2.9. This representation indicates that the flotation bay layout employing the larger flotation cells, in this case 2.83 cubic meter (100 cubic feet) machines, occupies less area and reduces installed capital cost by about 25 percent. However, there are instances when the first illustration (selection of small flotation cells) would be chosen for reasons of compactness and symmetry.

Complex multiple product flotation installations usually require a high degree of sophistication regarding operational control. Many times, in small flotation concentrators this level of sophistication is not available. If the facility is located in a remote area, experienced operational personnel may be impossible to acquire. Consequently, the flotation circuits should be as simple as possible. For an installation producing a single mineral product, the flotation scheme illustrated in Figure 6 is recommended. This system, which is compatible with configuration 2 on Figure 5, is simple to operate and eliminates the build-up of a large circulating load of scavenger concentrate. This system is also flexible in that various produced concentrates can be subjected to regrinding should changes in mineralogy or primary grind so dictate.

It must be recalled that the weight of rougher and cleaner concentrates produced from high-grade ores can be substantial. Provision to remove froth by the use of froth paddles on all flotation cells should be included in the original design. The additional capital cost required for froth paddles is a reasonable investment since these devices tend to negate errors in flotation pulp level or frother addition. The open circuit flotation system presented can be operated by individuals having minimal training. The advice of Taggart regarding the inclusion of a small pilot table as a visual sample on rougher tailings is still legitimate.

In almost all new flotation installations, the use of launders fabricated from sheet rubber is recommended. Care must be taken to insure that all launders are sloped properly. In addition, launders must be provided with appropriate sprays and sluice lines to facilitate concentrate transport. The launder water system must be carefully designed to insure functionality without excessive concentrate dilution.

In recent years it has become popular to use vertical pumps for both concentrate and tailing transport in smaller circuits. It is usually possible to employ only one, or at the most two, pump sizes for all of the required flotation pumping installations. The same size vertical pump may also be used in various locations about the plant for cleanup duty. The usage of vertical pumps reduces seal water requirements, and eliminates concrete pump bases, fabricated sumps, and the valving associated with horizontal pumps.

For the past 35 years Sub-A Flotation Machines have been serving faithfully in all parts of the world. Anniversaries of progress such as this make reminiscing very interesting and we thought you would enjoy seeing some of the Firsts in the flotation machine industry as pioneered by the Sub-A.

1928was a pioneer in the use of V-belt drives in the flotation industry. This high-head machine also had wide-spaced greaseless lower bearings. At one time this was the largest flotation machine in the world.

1930 First steel tank flotation machine. Earlier machines had wood tanks. Steel tanks met great opposition at first, later became standard. This high-head, all-steel Sub-A marked the introduction of anti-friction lower bearings.

1932 First low-head flotation machine marked a radical departure from the then accepted principle that the space between bearings must be greater than the distance beyond the lower bearing. This machine was of the cell-to-cell pulp flow design and used a quarter-turn flat belt line-shaft drive.

1933 First steel tank low-head, low-level flotation machine. It had an individual motor and a V-belt drive. This design became very popular with mill operators and thousands of cells were sold similar to those pictured above.

Laboratory Flotation Machines have made progress, too. In our early days the cast-iron tank machine with its round-belt mule drive was the latest word. Contrast it with todays modern Sub-A Laboratory Flotation Machine with its heavy glass tank and stainless steel parts.

1961 Todays demands for Sub- A Flotation Machines keep our modern factory busy. Today more Sub- A Flotation Machines are specified than all competitive makes and is the unquestioned First Choice in Flotation.

Related News
  1. flotation machine online
  2. flotation cell quiz
  3. flotation gear crossword
  4. gold flotation machine project pdf
  5. kraut flotation cell
  6. flotation process in graphite mining
  7. china flotation machine
  8. flotation cell 10
  9. high quality environmental coal flotation machine sell at a loss in paris
  10. mine flotation equipment for graphite mine in goa
  11. wear parts of ball mill new york
  12. raymond roller mill sizes
  13. used vibrating screen
  14. 220v 200w electric grain mill spice herb grinder pulverizer powder machine
  15. reliable performance capsule self condensing dryer
  16. ecuador wheels to crushers
  17. used drum magnetic separators for sale binq mining
  18. dry powder briquetting machine
  19. portable rock crusher gold for sale
  20. m processing ajmir mineral ball mill corpn ajmer