how to get sand out of a top-loading he washer | funny about money
Here in urban Arizona, we homeowners have something called desert landscaping. This is some Easterners idea of an approximation of what the Sonoran Desert looks like: a load of gravel spread over the yard and punctuated with a few cacti, a palm tree or two, and an ocotillo. Since the cost of watering a lawn easily exceeds a summer air-conditioning bill (which can be whopping!), this type of xeriscaping is cost-effective, if not what youd call aesthetically awe-inspiring.
An alternative to the ugly, footpad-piercing gravel is a product called quarter-minus. This stuff appears to be a by-product of sand-and-gravel operations: its a blend of finely crushed granite and gritty stuff that looks a lot like sand. Quarter-minus has three advantages: piled on deep enough, it inhibits weed growth; it vaguely resembles the desert floor (sure does that better than gravel, anyway); and after its been watered or rained on a few times, it packs down into a hard surface that your dogs can walk around on. This latter obviates their getting mud all over their feet and tracking it into the house.
Mud in Arizona is not your ordinary East-Coast mud. The soil here has a lot of clay in its extreme form, it creates a kind of hardpan called caliche. This stuff is sticky. When the dog tracks regular wet dirt into the kitchen, the stuff adheres to the tile flooring like paint. You literally have to get down on hands and knees and scour it off. It will not wipe up with a rag or paper towel you have to use a scrub brush or one of those sponges with a scouring pad on the back.
Ruby the Corgi Puppy, being a high-energy sort of soul, is given to chasing around the yard like a rocket with Cassie. And Cassie, being a corgi herself, is also a bit of a rocket. Theyve built a race track around one of the orange trees. Where theyve established their route, the quarter-minus is churned up and loose. And that means whenever it gets wet, they track a film of fine sand into the kitchen.
The other day one of the dogs wuffed on the rug, so I put it in the accursed Samsung washer. And it came out just fine, since its flat. Flat things are the only things the Samsung will run through an entire wash cycle without disgorging them in the form of braids.
A few days later, I decided to toss a pair of jeans that Id worn just a couple of hours into the rinse-&-spin cycle, knowing this would shake out the wrinkles and give me another wearing before I actually had to wash the things by hand, as I now have to wash everything thats not flat by hand. Twenty minutes later, I come back to retrieve the pants andWH-A-A-A?????
I get out the shop vac and vacuum out the sand, running the nozzle not only over the bottom but all over the tubs walls, hoping to suck out whatever sand is caught in the little holes that perforate the tubs side from top to bottom. I fill a scrub bucket with cold water and attempt to rinse the sand out of my jeans.
Then I run the pants through the washer again, only on a full Quick Wash cycle. In the wondrous world of HE washers, quick means 45 minutes. I figure an endless slosh like this should knock the remaining sand out of the jeans and rinse it out of the washer.
I wipe out the washer with a microfiber rag, put the jeans to soak with some detergent in a bucketful of water and run the Bedding cycle with the machine empty. Bedding is the only cycle that causes the Samsung to dispense enough water to actually clean a load of wash, more or less. The Bedding cycle takes an hour and ten minutes to run. Maybe, I hope, that much water slopping around that long will be enough to wash the sand out.
Have you counted up the amount of time were at now? One rinse, two quick washes, two bedding cycles: that adds up to 4.17 hours of run time. That doesnt count the time spent vacuuming and wiping down the washer and manually rinsing sand out of the clothing.
Now I raid the linen closet and haul out four large towels, one of them a gigantic Costco beach towel. These I dump into the washer with a generous slug of home-made fabric softener (hair conditioner diluted with water works as well as fabric softener and it doesnt stink). Run it all through on Bedding again, the second-longest cycle the Samsung provides.
This seems to work. Theres still some sand in the washer, but a lot less. I shake out the towels in the backyard, attempting to dislodge as much sand as possible. Wipe out the inside of the washer again. Toss them back into the washer. Run the washer again.
Holy mackerel! What would you do if you lived near a beach? Just keep buying new $1500 washers every six months or so? Learn to replace the pump yourself and keep a lifetime supply of the things in the garage?
Unfortunately, just now I do need to keep a grip on the expenses. I dont feel I can afford another washer, having recently dropped something over $1200 plus 10% taxes on this thing. Very soon now, I need to buy a car, which I also cant afford.
Besides, I suspect poor performance is a characteristic of HE machines, just as not flushing is a characteristic of water-efficient toilets and just as taking half an hour to rinse the shampoo out of your hair is a characteristic of low-flow showerheads.
Without a car, I cant buy food or clothing or medications. Without a wash machinewell, nothing much happens, because I do know how to wash clothes in the utility sink. So given that I cant really afford either one, I guess if Im going to have to be strapped, Id better be strapped over the car and not over yet another useless washing machine.
Im not exactly sure what the HE stands for. Perhaps it is the new front loading washer? However, there are tons of the old fashioned kind still out there and for sale, cheap, when people move. Honestly, for what you saved from going on fewer trips to Costco I think you could snag one. This is 2015, you shouldnt have to wash in a utility sink. For a tiny amount of money and an hour of muscle from your son, you could be up and running again.
Minnesota Public Radio
San Francisco Public Radio
Los Angeles Public Radio
Boston Public Radio
Phoenix Public Radio
Christian Science Monitor
New York Times (paywall)
Washington Post (paywall)
can you pressure wash polymeric sand? (find out now!) upgraded home
When youre creating your dream garden, the chances are high that pavers are going to be involved. You can make beautiful paths, patios, or small areas for birdbaths. Polymeric sand is a handy ingredient that acts as a cement-like material to keep the pavers in place.
There are several easy ways that you can clean pavers with polymeric sand, including pressure washing. If you recently poured polymeric sand, you cant pressure wash it. If its been set, you can use a pressure washer as long as the water is relatively cold.
Below well talk about how you can clean pavers where youve applied polymeric sand. In case this type of filler isnt meeting your needs, Ive also added a handful of alternatives. The handy buyers guide will give you a good idea of what you can expect to pay as well.
The key to cleaning polymeric sand-filled pavers correctly actually lies in the application of the sand itself. If it isnt applied correctly, things like a pressure washer will cause more harm than good. These are the steps to properly use the sand and get a seamless finish.
The first thing youll want to do is pour the sand out in one area after laying your pavers. Sweep the polymeric sand into all of the joints. Make sure that this is done evenly to give a more cohesive final look.
For the third step, simply repeat the first two steps. Adding polymeric sand in rounds allows it to settle evenly in every crack and crevice. When sweeping, its important not to clean too hard, so the sand to go off into the sides.
Continue sweeping in the sand, but dont tamp it down this time. Youll want the filler as close to the tops of the pavers as possible. Doing so makes an even final surface and reduces any unwanted dips or divots.
This step is essential: make sure there isnt any sand leftover on the pavers themselves. If there is, sweep it off or use a leaf blower at an angle. Once you wet the sand, it can be incredibly challenging to remove.
Spray water all over the paved areas using a misting setting. A harsh water pressure, like a pressure washer, will kick up the sand and make a mess. Start by spraying higher and slowly get lower as you go.
Its a good idea to cover it with a lifted tarp if any rain or severe weather is expected. Even while its curing, you dont want polymeric sand to get wet again. It can be a pain to remove, and its best to take small steps to avoid that from happening.
After the polymeric sand is completely cured, you can use your pressure washer to clean it. There are several easy ways to make your patio pavers look brand new. Here are the simplest (and cheapest) ways to get the job done.
A pressure washer allows you to remove tough stains and get rid of tough buildup. Things like grass, leaves, and spills can leave ugly marks on your patio. One of the crucial tips when it comes to using a pressure washer is to make sure the water isnt too warm.
If polymeric sand is met with a heat of 185 degrees, it can become dislodged. Another tip is to not go full blast using this cleaning method either. Only use a higher pressure when trying to remove stains.
Something to note if you do plan on using a pressure washer is the need to reapply sand. This can be a spendy way to clean your patio if you do it often. The average home washes their patio three to four times per year.
If you need to clean your pavers more often, thats totally okay. Get a bowl with some warm, soapy water. Again, watch the temperature of the water when working with polymeric sand. You can get a brush, cloth, or sponge, and spot clean the dirty areas.
As a homeowner, youll eventually learn that white vinegar is an excellent cleaning agent. Its essential to use white vinegar, as dark can stain pavers. Mix a one to one ration and pour it all over your patio.
To prevent your pavers from getting stained in the first place, regularly sweeping them can help. Youll want to do this at least once a week, more if you live somewhere with a lot of trees and plants.
The most common alternative is to use cement. Its known to keep pavers in their place by creating a strong bond. Cement works very similarly to glue, and it takes about eight pounds of cement to fill a 44 patio.
While it is a great replacement, not every store will have it available. It also doesnt stay in place like cement does. Its an excellent product for landscaping and can give a smooth layer underneath pavers.
Pricing for polymeric can vary from one store to another and region to region. Its common for prices to fall between $20 and $40 per 50-pound bag. In the long run, using polymeric sand will save you money from not having to relay the interlocking pavers as often.
If it recently rained and the surface is still wet or damp, avoid putting in polymeric sand. Its essential to the setting process of this type of sand for it to be dry from the moment its poured. If theres a hard rain on polymeric sand that isnt completely set, the sand could go all over the pavers top.
Some polymeric sands contain cement, and this can create an unflattering haze that can be hard to remove. The most common way to get rid of the haze is to acid wash the surface until its noticeably clearer. There are specific polymeric sand cleaners that are designed to de-haze the finish.
I like to think of polymeric sand as an outdoor version of grout. Once its completely dried and cured, it creates a cement-like consistency. If properly installed, weeds wont grow between the joins, and the sand will stay in place.
Kirstin is a passionate writer who loves helping people learn new things when it comes to home improvement. When shes not behind a keyboard, she enjoys DIY projects, crafts, spending time with her pets, and making videos. She hopes that with all she writes, someone is finding a solution to their home improvement needs.
13 faults and solutions for sand washing machine | fote machinery
washing machine is one of the washing equipment especially designed for artificial sand and natural sand. In general, there are two kinds of the sand washing
machine: spiral sand washing machine and wheel type sand washing machine.
remove the impurities that covered in the surface of sand and aggregate and
destroy the vapor layer wrapped around the sand particles, so as to
high-efficiently clean and dry the sand and aggregate.
the operation process, users will inevitably encounter a variety of faults.
Fote Heavy Machinery shares some solutions to the common faults of the sand
washing machine, hoping you can get help.
As a leading mining machinery manufacturer and exporter in China, we are always here to provide you with high quality products and better services. Welcome to contact us through one of the following ways or visit our company and factories.
Based on the high quality and complete after-sales service, our products have been exported to more than 120 countries and regions. Fote Machinery has been the choice of more than 200,000 customers.
how to wash beach towels
Nothing says summer like a bright and colorful beach towel spread over white sands, a shady picnic spot, or a poolside lounge chair. But those towels take lots of abuse from sand, salt, chlorine, sunscreen, and tanning products. Knowing how to best wash and clean your favorite beach towel will help it last for many summers to come.
Whether you are spending a lazy week at the beach or just taking a quick dip in the pool, the towel you use is coming in contact with body soil and bacteria as well as environmental factors. Ideally, a beach towel should be washed after every use.
However, when you're on vacation, that may not be possible. Between uses, the towel should be hung to dry, preferably in the sun where it will dry quickly and take advantage of the ultraviolet rays that help with sanitation. If you want to keep the bright colors, rinse towels that are used by the pool each day to remove chlorine residue that can fade colors.
After every use, it is important to remove any loose land or soil from the fibers of the towel. Even if the towel is wet, give it a vigorous shake (preferably away from unsuspecting sun-lovers) to remove debris. Since sand will cling to a wet towel, hang the towel to dry completely and then give it a good shake again.
Besides the uncomfortable feel of a sandy beach towel on your skin, there is another reason to get rid of as much sand as possible after every use. Excessive sand or grit in the towel can cause your washer to malfunction. All of that sand flows toward the washer's filters and causes them to become clogged. This leads to washer leaks and broken water pumps.
While most beach towels are made of thick, absorbent cotton, there are towels made of synthetic microfibers. Take the time to look at the care label to find out the fiber content and washing instructions.
If you don't have enough towels to make a full load, other types of laundry can be added. Just be sure to choose fabrics that do not attract lint. No one needs a sleek swimsuit or rash guard covered with cotton lint.
If washing the towels in a top-load washer with a center agitator, place them evenly around the center post to keep the washer in balance. For every type of washer, do not overload the washer drum. The towels need room to move in the cleaning solution to get really clean.
If you plan to toss the towels in the dryer, you can opt for a lower washing water temperature (warm or cold). The heat of the dryer will take care of any lingering bacteria. However, if someone using the towels has athlete's foot or any other type of fungal or bacterial infection, opt for hot water. Instead of a short or gentle cycle, choose the regular wash cycle so that the towels spend plenty of time in the detergent solution.
For the best results, choose a heavy-duty detergent (Tide and Persil are brand names) that contains enough enzymes to break apart soil and stains so they can be washed away. By using a heavy-duty detergent, you probably won't need to pretreat stains.
To keep towels as absorbent as possible, skip commercial fabric softeners that coat the fibers. Simply add one cup of distilled white vinegar to the rinse cycle to strip away any detergent residue that leaves towels stiff and scratchy. They won't smell like a pickle, just clean and fresh and soft to the touch.
Before you toss the beach towels into the dryer, check them for any stains or discoloration. If you see color bleeding, dark stains from self-tanners, or yellowing from sunscreen, skip the dryer until you can treat the problem. The heat of the dryer will set the stains and make them very difficult to remove.
Once the towels are washed and clean of all stains, choose your dryer's moisture-sensing cycle. This way the machine will stop when the towels are dry to avoid over-drying them. Beach towels can be hung on a clothesline to dry, too.
Beach towels can easily fade with lots of use and from being exposed to sun, salt, and chlorine for extended periods of time. Do not use chlorine bleach on towels, as this can weaken the fibers and further fade the fabric. For cotton towels, use anoxygen-based bleach, as it will work more slowly. See our guide on how to wash cotton for best practices. Always be sure to read the product labels and follow the recommendations.
how to clean beach sand: 12 steps (with pictures) - wikihow
This article was co-authored by our trained team of editors and researchers who validated it for accuracy and comprehensiveness. wikiHow's Content Management Team carefully monitors the work from our editorial staff to ensure that each article is backed by trusted research and meets our high quality standards.
There are 9 references cited in this article, which can be found at the bottom of the page.
wikiHow marks an article as reader-approved once it receives enough positive feedback. In this case, 92% of readers who voted found the article helpful, earning it our reader-approved status.
This article has been viewed 61,734 times.
There are lots of ways to clean beach sand for crafts projects. Sift out rocks and other debris, and rinse away organic matter and silt. If you need sterile sand, try baking it for 45 minutes. Remove salt by simmering the sand with water, then straining it through a coffee filter. To avoid bringing sand home after a beach trip, hit the showers and rinse off toys and other items before getting in your car. In a pinch, baby powder works well as a sand remover. If all else fails, use a handheld vacuum to clean up sand in your home or car.
Cleaning beach sand for your aquarium, garden, or art project is relatively easy. Collect twice as much sand as youll need, since youll probably lose a bit during the cleaning process. To get rid of rocks and debris, sift your sand through a colander or strainer. You can also rinse out the debris. To do this, half fill a bucket with water, gradually stir in your sand, then dump out the water. You might need to repeat this a few times until your sand looks clean. If you want to remove the salt from your sand, pour it into a pot, cover it with water, and heat it on the stove. When it reaches a boil, turn the heat down and simmer it for a few minutes. Then, pour it through a large coffee filter to collect the sand. For more tips, including how to sterilize your beach sand by baking it, read on!
Did this summary help you?YesNo
sand washing machine - eastman rock crusher
In the production of artificial sand, or processing natural sand, sand washing machines are widely used. Those washing equipment help wash and separate the soil or other impurities in sand (artificial sand, natural sand) and gravel aggregate.
The sand after being cleaned by the sand washer will get a more cleaner and pretty looks and achieve a better quality, thats make the sand reach the quality request and help sold with a higher price in the market, so the sand washer has gradually become an important equipment of the artificial sand production line.
When sand washing machine working, the impellors run slowly with the sand washer motor after decelerated by the decelerator, gears wheel and belt. The sand and stone flow into washing tank from feeding launder grinds with each other and rolls with the impellor slowly, the impurities covered in sand is washing out.At the same time, the washing water will take some wastes and impurities away from washing tank also. The washed sand and stone is lifted up by impellor. When it rolls up slowly, the water begins to drop through the meshes and fall back in the washing tank, the water can be fully used. Finally, the clean sand and stone goes out of the washing tank and the washing process is over.
The use of hyrocyclones in sand washing machines is the most efficiency method for sand washing process, because it lets to recovery sand without losing fines.When working, the waste water pruduced during the washing process is extracted by slurry pump, and feeding into hydrocyclone, then the 0.074-3mm fine sand will be recycled in the cyclone.
Coarse sand (3-10mm) and fine sand (0.074-3mm) are feed onto polyurathane screen panels for dewatering, after dewatering process the water content is in 8-12% and those sands can be conveyed, piled up or transported.
Our washing machine has powerful washing capabilities:Typically, our wheel sand washing machine has a capacity of 15-200 tph, and our spiral sand washing machine has a more powerful washing ability with a capacity of 70-350 tph.Whats more, you can contact our engineer to get fully customized with the number of impellers or screws and the length to increase the max capacity.
From the actual production situation, Spiral sand washer has a more powerful washing ability, which can wash larger gravel with serious mud impurities effectively . So, it is often equipped in large-scale sand production lines.
For our wheel-type sand washer, our data shows the loss of fine sand and stone powder is small, and the water consumption during sand washing is less. And our strict test shows the gradation and fineness modulus of the washed sand can meet the standard requirements;Compared with wheel sand washers, spiral sand washers lose more fine sand during cleaning, and our experimental data also proves that the sand cleaned by spiral sand washer is more clean.
However, when choosing sand washers, users should consider the composition of sand and gravel, expected production capacity, factory site conditions and other factors, and choose the most suitable machines for their requirements.
Yes, our sand maker is fully customizable. Our customers can freely choose to increase the number of washing wheels according to the conditions of sand and gravel. Whats more, If the clay content of sand and gravel is high or the output need to be increased, our spiral sand washer can also increase the length of the auger shaft or use double helix side by side, also it can also be divided into single screw sand washer and double screw sand washer. You can contact us for a full customize for your situations.
While the price of spiral sand washer is relatively higher, which belongs to the type of high-grade and Large-output sand washer. And the detail price can vary from your customized, so please contact our sales for more information.
how to clean your clothes washer's water line filters
Clothes washers have filters on the hot and cold intake water lines to prevent debris in the water line from getting into the washer. Over time these filters can become clogged with sand and sediment and need to be cleaned.
Joe Truini: If your washing machine seems to take forever to fill with water, heres the reason why. If you disconnect the hoses on the back side, youll see that there are small filters inside each of the hot and cold water fill. And those filters are designed to keep sediment such as sand, dirt, and minerals from passing through into the machine. So what you need to do at least two or three times a year is clean out the filter, and heres an easy way to do that.
Take a plant mister filled with water and hold a cup underneath it just to catch some of the water and dirt, and just spray right in there. And youll see the dirt comes right out. See that? And then what I like to do, most of the dirt comes out just with that. What I like to do is come back with a small acid brush, and just scrub it a little bit just to get any stubborn bits of dirt and sand out, and then spray it one more time. And of course, you need to do this on both the cold and the hot.
this is a great tip. thank you. i have previously cleaned the filters using a qtip, but that did not do a great job and the filters kept re-clogging. i had not thought about using a mister. I was amazed at how much grit came out.
I have a problem with a film in my washer at the water line on the tub. I have tried vinegar with hot water, new stainless hoses, removed agitator cleaned it, squirted vinegar in holes in washer and still get film after one load of wash at water line on tub.
Live close to beach, but try to rinse out towels and swimsuits well, prior to
washing in top load washer. At times, I notice sand particles left on clothing, after washing cycles are completed. Also, some sand at bottom of washer tub. Will cleaning water line filters help? Im thinking there may be a form of blockage within the many vents in the laundry tub. Any suggestions, please.
This worked great for about five minutes then when I took the hoses off the cold water one was clogged with heavy grit and dirt. Our well water gets gritty and dirty when it rains heavy. My question is there a more permanent solution as in a small filter to keep it from clogging the tiny screen going into the washer. I cant afford anything elaborate but I need something! Thank you so much for your help and website, we all need help once in a while ?
I have a new Whirlpool HE Turbo front loader. When I did a normal whites load of wash I had gotten an F1 code. The water didnt drain but kept on sloshing the clothes back and forth. I finally canceled and then drained and spun the clothes. Does the F1 code mean that there is a problem with the washer, or should I assume the screens are clogged? The washer is new and I have only done about 10 loads of wash. Thank you.
guide to change sand in your pool filter | pool maintenance
A sand filter pushes your pool water through layers of sand, which functions as the filtration medium in the filter tank. The sharp edges of the sand grains capture contaminants as the water passes through the filter.
The size of the sand granules is critical for optimum filtering efficiency. If the granules are too big, youll see less filtering efficiency; if the granules are too small, you risk clogging the filter quickly.
Chemical flocculants or diatomaceous earth (DE) powder can also be spread over the top layer of sand to improve the filter performance. Flocculants attract floating microscopic debris and cluster the particles together into chunks large enough to sink and be vacuumed up. DE powder is pulverized plankton fossils (called diatoms) that coats the filter element to collect impurities.
A little debris can actually aid in filtration. When the sand bed is completely clean, some of the smallest particles will pass through unfiltered. As the sand bed begins to accumulate the impurities, the filter can catch more and more as accumulated particles attract.
Be sure you have everything you need on hand before you begin the process. Your list of essentials can include sand, a replacement O-ring between the valve and the tank, Teflon tape, lubricant, and unions.
Remove the drain cap at the bottom of your filter tank to release the pressure in the filter and drain the water. Give the drain cap at the bottom of the tank just half a turn counter-clockwise to let out all the air. After a burst of air pressure, remove the cap to drain out the water. If you dont want the water emptying directly onto the ground, quickly attach a hose over the drain after you remove the cap to direct the draining water elsewhere.
Disconnect the pump, return, and waste hoses fixed to the multiport valve at the top of your filter. After those port attachments are off, take out the multiport valve flange clamp that secures the filter in place. Unscrew the bolts that separate the clamp, and pull deliberately and consistently to lift the valve off the pipe.
If your multiport valve has unions, just unscrew them from the multiport valve. If you do not have unions, youll need to cut the pipes running to and from your filter. It might be a good time to install unions before reassembling to make future maintenance easier. Make sure you leave enough exposed pipe after the cut to add both sides of the unions.
As soon as you disconnect the pipe from the multiport valve, tape the end of the pipe closed to prevent sand from entering it and clogging the laterals. After you tape off the pipe, empty out all the existing sand. Scoop it out with a plastic cup or vacuum it out with a shop vac until the top of the laterals at the bottom of the tank are visible.
Slowly rotate the 10 lateral pipes upwards, then smoothly pull the lateral assembly and pipe out of the rest of the sand. Inspect the laterals for damage, replace any that look broken or worn out. Clogged laterals should be soaked in a bucket of cleaning solution for a few hours, then thoroughly rinsed and reinstalled onto the assembly.
Thoroughly wash out the tank with a garden hose. Check the drain cap, and swap it out with a new one it if you find any cracks. Fill the filter tank hallway up with water to provide a cushion and protect the laterals from getting clogged when you pour in the new sand.
Tape off the top of the pipe to prevent sand from entering and clogging the laterals. Keeping the pipe centered in the tank, carefully and slowly pour sand into the filter unit. Add enough sand so that the laterals are completely covered. Level the sand as you pour to ensure even sand distribution for effective filtration and water circulation.
Pro tip: When adding new sand, take care not to lift the lateral assembly and pipe off the bottom of the tank. You wont be able to push it back down without rotating the laterals up, and upward-facing laterals will prevent proper filtering.
Remove the O-ring at the bottom of the multiport valve and inspect for excessive wear-and-tear. Since you only perform this procedure every 5 years or so, its a smart choice to go ahead and replace the O-ring now, even if yours is in decent shape. O-rings are really inexpensive, and they do wear out.
Remove the tape from the end of the pipe, and carefully set the multiport control valve back in its original position on the central pipe. Secure the valve clamps around the tank and tighten them into place. Reconnect the unions with the pool pump and the return ports.
With the pump still switched off, rotate the valve handle to the Backwash setting and then turn on the pump. After its fully primed, run the pool pump for about 2 minutes to flush out the impurities in the water and the finer sand particles from the sand media, and to ensure that your pool water waste is exiting at the right place.
Once the backwash water runs clear and clean, turn the pool pump off. Switch the multiport valve to Rinse, then turn the pump back on. After about a minute, the water in the sight glass should be clear.